Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Are multitool saws resharpenable?

Scheduled Pinned Locked Moved General Tool Discussion
25 Posts 1 Posters 1.8k Views
  1. Home
  2. Tool Talk
  3. General Tool Discussion
  4. Are multitool saws resharpenable?
Are multitool saws resharpenable?
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • AimlessWanderer Offline
    AimlessWanderer
    Posts: 17,518
    AimlessWanderer Offline
    AimlessWanderer
    wrote on last edited by
    #10 Quote Reply

      @Syncop8r said:
      I'm just thinking of how the likes of Irwin and Bahco handsaws get used and discarded on building sites as opposed to traditional handsaws which get sharpened.

      A) not cost effective due to time taken
      B) sharpening will remove case hardening

      @Syncop8r said:

      @50ft-trad said:

      The Leatherman pull cutting edges won't accept this file, as the groove is more acute than 60o, however a small half round (which usually has a larger radius than half the file width) may be able to sharpen them albeit only to a partial tooth depth.

      To me it looks like the angle could be 60º, just that the file would be rotated.

      You're right. I must have been having a incompetent moment :facepalm:

      Just checked the ST300 and KF4. I'll go back and check the SOG and Diesel :salute:

      1 Reply Last reply
      • AimlessWanderer Offline
        AimlessWanderer
        Posts: 17,518
        AimlessWanderer Offline
        AimlessWanderer
        wrote on last edited by AimlessWanderer
        #11 Quote Reply

          Yeah, the SOG and Diesel can be done with a triangular file too, but they're at a wazzy angle (like the LM's) so it's not as easy a process as the Vics. You have to rotate the file, angle it to the cutting geometry AND angle the file upwards too. :ahhh It certainly seems to me that the Vics would still be a lot easier to sharpen. Not got any Wenger saws anymore.

          1 Reply Last reply
          • Syncop8r Offline
            Syncop8r
            Posts: 8,801
            Syncop8r Offline
            Syncop8r
            wrote on last edited by
            #12 Quote Reply

              @50ft-trad said:

              @Syncop8r said:

              I'm just thinking of how the likes of Irwin and Bahco handsaws get used and discarded on building sites as opposed to traditional handsaws which get sharpened.

              A) not cost effective due to time taken

              Supposedly it only takes about 4 minutes to sharpen a resharpenable saw - let's make it 5 so 1/12 of an hour. So what costs more: a new (disposable) saw, or 1/12 of your hourly rate?
              Perhaps it's more a case of the CBF attitudes of our disposable modern mindset?

              1 Reply Last reply
              • AimlessWanderer Offline
                AimlessWanderer
                Posts: 17,518
                AimlessWanderer Offline
                AimlessWanderer
                wrote on last edited by
                #13 Quote Reply

                  @Syncop8r said:

                  @50ft-trad said:

                  @Syncop8r said:

                  I'm just thinking of how the likes of Irwin and Bahco handsaws get used and discarded on building sites as opposed to traditional handsaws which get sharpened.

                  A) not cost effective due to time taken

                  Supposedly it only takes about 4 minutes to sharpen a resharpenable saw - let's make it 5 so 1/12 of an hour. So what costs more: a new (disposable) saw, or 1/12 of your hourly rate?
                  Perhaps it's more a case of the CBF attitudes of our disposable modern mindset?

                  All I know is that it would take me personally a heck of a lot longer than that :D Not like these guys ....

                  - YouTube

                  Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.

                  favicon

                  (www.youtube.com)

                  I have a couple of old saws that I really ought to have a go at getting back working again (assuming they're just blunt and don't have any broken teeth)

                  1 Reply Last reply
                  • Syncop8r Offline
                    Syncop8r
                    Posts: 8,801
                    Syncop8r Offline
                    Syncop8r
                    wrote on last edited by
                    #14 Quote Reply

                      Awesome vid! :tu:

                      @50ft-trad said:
                      All I know is that it would take me personally a heck of a lot longer than that.... I have a couple of old saws that I really ought to have a go at getting back working again (assuming they're just blunt and don't have any broken teeth)

                      Perhaps these will help?

                      Sharpening rip saws:
                      https://www.youtube.com/watch?v=UA5DixEaaUo

                      Sharpening crosscut saws (pertinent to multitool saws):
                      https://www.youtube.com/watch?v=_fNosQU1Ujg

                      1 Reply Last reply
                      • AimlessWanderer Offline
                        AimlessWanderer
                        Posts: 17,518
                        AimlessWanderer Offline
                        AimlessWanderer
                        wrote on last edited by
                        #15 Quote Reply

                          :salute:

                          1 Reply Last reply
                          • AimlessWanderer Offline
                            AimlessWanderer
                            Posts: 17,518
                            AimlessWanderer Offline
                            AimlessWanderer
                            wrote on last edited by
                            #16 Quote Reply

                              Unlike in those sharpening tutorials, I noticed in some of the saws you have to angle the file away from horizontal, as well as rotating axially and angling away from perpendicular. I think the trick is to sharpen multitool saws while there is still plenty of tooth form to act as a guide for the file. Going back to the hardness, I don't have saw files, but my diamond files would do the job just fine :tu:

                              1 Reply Last reply
                              • Syncop8r Offline
                                Syncop8r
                                Posts: 8,801
                                Syncop8r Offline
                                Syncop8r
                                wrote on last edited by
                                #17 Quote Reply

                                  I might need a diagram to understand some of that.... :think:

                                  I have a saw file but it's probably too big for multitools. I will use the triangular file that came in a set of cheap needle files.

                                  1 Reply Last reply
                                  • Zed Offline
                                    Zed
                                    Posts: 19,555
                                    Zed Offline
                                    Zed
                                    wrote on last edited by
                                    #18 Quote Reply

                                      Going on how easy they bend and bend back I think these will be easy to sharpen, I'll need to give it a go but none of mine are blunt yet :D

                                      1 Reply Last reply
                                      • pfrsantos Offline
                                        pfrsantos
                                        Posts: 24,165
                                        pfrsantos Offline
                                        pfrsantos
                                        wrote on last edited by
                                        #19 Quote Reply

                                          Glad to see you answer your own questions.

                                          :D :D :tu: :tu:

                                          1 Reply Last reply
                                          • Syncop8r Offline
                                            Syncop8r
                                            Posts: 8,801
                                            Syncop8r Offline
                                            Syncop8r
                                            wrote on last edited by
                                            #20 Quote Reply

                                              @pfrsantos said:
                                              Glad to see you answer your own questions.

                                              :D :D :tu: :tu:

                                              :think:

                                              The question was not how to resharpen them, but rather can they be resharpened.

                                              1 Reply Last reply
                                              • Dutch_Tooler Offline
                                                Dutch_Tooler
                                                Posts: 4,434
                                                Dutch_Tooler Offline
                                                Dutch_Tooler
                                                wrote on last edited by
                                                #21 Quote Reply

                                                  Well, the nitpicker in me says, if there's an answer to the question "how" that implies that the answer to "if" is "yes"... :think: :angel:

                                                  Sent on my SM-G930F with Tapatalk

                                                  1 Reply Last reply
                                                  • VICMAN Offline
                                                    VICMAN
                                                    Posts: 15,047
                                                    VICMAN Offline
                                                    VICMAN
                                                    wrote on last edited by
                                                    #22 Quote Reply

                                                      @50ft-trad said:
                                                      The Victorinox double acting saws are sharpenable with a small triangular diamond file. Care is needed, but if you get the file aligned correctly, passing the file down each tooth groove will sharpen both the push and pull cutting edges either side of the groove.

                                                      The Leatherman pull cutting edges won't accept this file, as the groove is more acute than 60o, however a small half round (which usually has a larger radius than half the file width) may be able to sharpen them albeit only to a partial tooth depth.

                                                      I haven't checked the Gerber and SOG offerings, but I am confident I could sharpen both with my small diamond files.

                                                      Thanks for the info! :like:

                                                      1 Reply Last reply
                                                      • AimlessWanderer Offline
                                                        AimlessWanderer
                                                        Posts: 17,518
                                                        AimlessWanderer Offline
                                                        AimlessWanderer
                                                        wrote on last edited by
                                                        #23 Quote Reply

                                                          @VICMAN said:

                                                          @50ft-trad said:

                                                          The Victorinox double acting saws are sharpenable with a small triangular diamond file. Care is needed, but if you get the file aligned correctly, passing the file down each tooth groove will sharpen both the push and pull cutting edges either side of the groove.

                                                          The Leatherman pull cutting edges won't accept this file, as the groove is more acute than 60o, however a small half round (which usually has a larger radius than half the file width) may be able to sharpen them albeit only to a partial tooth depth.

                                                          I haven't checked the Gerber and SOG offerings, but I am confident I could sharpen both with my small diamond files.

                                                          Thanks for the info! :like:

                                                          Vicman,

                                                          It turned out that the 60o diamond file worked on the other saws too. They are just harder to align with the tooth form on the pull saws :cheers:

                                                          1 Reply Last reply
                                                          • Syncop8r Offline
                                                            Syncop8r
                                                            Posts: 8,801
                                                            Syncop8r Offline
                                                            Syncop8r
                                                            wrote on last edited by Syncop8r
                                                            #24 Quote Reply

                                                              Did you need to use a diamond file?

                                                              EDIT: Disregard - I just re-read an earlier answer of yours:

                                                              @50ft-trad said:
                                                              I don't have any standard tool steel jewellers files to check this with. I can't imagine the saws being treated too highly as nobody wants a saw with brittle teeth, but I don't know what hardness jewellers files are taken to either. As an aside, I think a lot of saw blades (and plier teeth) are laser treated to case harden them rather than a soak and quench type process.i don't know whether this translates to multitool components too, or just dedicated tools.

                                                              Tl:dr = dunno :shrug:

                                                              1 Reply Last reply

                                                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                              With your input, this post could be even better 💗

                                                              Register Login

                                                              • 1
                                                              • 2
                                                              1. Home
                                                              2. Tool Talk
                                                              3. General Tool Discussion
                                                              4. Are multitool saws resharpenable?
                                                              Reply
                                                              • Reply as topic
                                                              Log in to reply
                                                              COMMUNITY LINKS
                                                              EDC-TV SAKWiki GearFeed SAKSelector
                                                              Operational Funds

                                                              Help us keep the Unworkable working!

                                                              Make A Donation
                                                              November Goal: $300.00
                                                              Due Date: Nov 30
                                                              Total Receipts: $0.00
                                                              Below Goal: $300.00
                                                              0% funded
                                                              • Login

                                                              • Don't have an account? Register

                                                              • Login or register to search.
                                                              • First post
                                                                Last post
                                                              0