Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Are multitool saws resharpenable?

Scheduled Pinned Locked Moved General Tool Discussion
25 Posts 1 Posters 1.8k Views
  1. Home
  2. Tool Talk
  3. General Tool Discussion
  4. Are multitool saws resharpenable?
Are multitool saws resharpenable?
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Syncop8r Offline
    Syncop8r
    Posts: 8,801
    Syncop8r Offline
    Syncop8r
    wrote on last edited by
    #14 Quote Reply

      Awesome vid! :tu:

      @50ft-trad said:
      All I know is that it would take me personally a heck of a lot longer than that.... I have a couple of old saws that I really ought to have a go at getting back working again (assuming they're just blunt and don't have any broken teeth)

      Perhaps these will help?

      Sharpening rip saws:
      https://www.youtube.com/watch?v=UA5DixEaaUo

      Sharpening crosscut saws (pertinent to multitool saws):
      https://www.youtube.com/watch?v=_fNosQU1Ujg

      1 Reply Last reply
      • AimlessWanderer Offline
        AimlessWanderer
        Posts: 17,518
        AimlessWanderer Offline
        AimlessWanderer
        wrote on last edited by
        #15 Quote Reply

          :salute:

          1 Reply Last reply
          • AimlessWanderer Offline
            AimlessWanderer
            Posts: 17,518
            AimlessWanderer Offline
            AimlessWanderer
            wrote on last edited by
            #16 Quote Reply

              Unlike in those sharpening tutorials, I noticed in some of the saws you have to angle the file away from horizontal, as well as rotating axially and angling away from perpendicular. I think the trick is to sharpen multitool saws while there is still plenty of tooth form to act as a guide for the file. Going back to the hardness, I don't have saw files, but my diamond files would do the job just fine :tu:

              1 Reply Last reply
              • Syncop8r Offline
                Syncop8r
                Posts: 8,801
                Syncop8r Offline
                Syncop8r
                wrote on last edited by
                #17 Quote Reply

                  I might need a diagram to understand some of that.... :think:

                  I have a saw file but it's probably too big for multitools. I will use the triangular file that came in a set of cheap needle files.

                  1 Reply Last reply
                  • Zed Offline
                    Zed
                    Posts: 19,555
                    Zed Offline
                    Zed
                    wrote on last edited by
                    #18 Quote Reply

                      Going on how easy they bend and bend back I think these will be easy to sharpen, I'll need to give it a go but none of mine are blunt yet :D

                      1 Reply Last reply
                      • pfrsantos Offline
                        pfrsantos
                        Posts: 24,165
                        pfrsantos Offline
                        pfrsantos
                        wrote on last edited by
                        #19 Quote Reply

                          Glad to see you answer your own questions.

                          :D :D :tu: :tu:

                          1 Reply Last reply
                          • Syncop8r Offline
                            Syncop8r
                            Posts: 8,801
                            Syncop8r Offline
                            Syncop8r
                            wrote on last edited by
                            #20 Quote Reply

                              @pfrsantos said:
                              Glad to see you answer your own questions.

                              :D :D :tu: :tu:

                              :think:

                              The question was not how to resharpen them, but rather can they be resharpened.

                              1 Reply Last reply
                              • Dutch_Tooler Offline
                                Dutch_Tooler
                                Posts: 4,434
                                Dutch_Tooler Offline
                                Dutch_Tooler
                                wrote on last edited by
                                #21 Quote Reply

                                  Well, the nitpicker in me says, if there's an answer to the question "how" that implies that the answer to "if" is "yes"... :think: :angel:

                                  Sent on my SM-G930F with Tapatalk

                                  1 Reply Last reply
                                  • VICMAN Offline
                                    VICMAN
                                    Posts: 15,047
                                    VICMAN Offline
                                    VICMAN
                                    wrote on last edited by
                                    #22 Quote Reply

                                      @50ft-trad said:
                                      The Victorinox double acting saws are sharpenable with a small triangular diamond file. Care is needed, but if you get the file aligned correctly, passing the file down each tooth groove will sharpen both the push and pull cutting edges either side of the groove.

                                      The Leatherman pull cutting edges won't accept this file, as the groove is more acute than 60o, however a small half round (which usually has a larger radius than half the file width) may be able to sharpen them albeit only to a partial tooth depth.

                                      I haven't checked the Gerber and SOG offerings, but I am confident I could sharpen both with my small diamond files.

                                      Thanks for the info! :like:

                                      1 Reply Last reply
                                      • AimlessWanderer Offline
                                        AimlessWanderer
                                        Posts: 17,518
                                        AimlessWanderer Offline
                                        AimlessWanderer
                                        wrote on last edited by
                                        #23 Quote Reply

                                          @VICMAN said:

                                          @50ft-trad said:

                                          The Victorinox double acting saws are sharpenable with a small triangular diamond file. Care is needed, but if you get the file aligned correctly, passing the file down each tooth groove will sharpen both the push and pull cutting edges either side of the groove.

                                          The Leatherman pull cutting edges won't accept this file, as the groove is more acute than 60o, however a small half round (which usually has a larger radius than half the file width) may be able to sharpen them albeit only to a partial tooth depth.

                                          I haven't checked the Gerber and SOG offerings, but I am confident I could sharpen both with my small diamond files.

                                          Thanks for the info! :like:

                                          Vicman,

                                          It turned out that the 60o diamond file worked on the other saws too. They are just harder to align with the tooth form on the pull saws :cheers:

                                          1 Reply Last reply
                                          • Syncop8r Offline
                                            Syncop8r
                                            Posts: 8,801
                                            Syncop8r Offline
                                            Syncop8r
                                            wrote on last edited by Syncop8r
                                            #24 Quote Reply

                                              Did you need to use a diamond file?

                                              EDIT: Disregard - I just re-read an earlier answer of yours:

                                              @50ft-trad said:
                                              I don't have any standard tool steel jewellers files to check this with. I can't imagine the saws being treated too highly as nobody wants a saw with brittle teeth, but I don't know what hardness jewellers files are taken to either. As an aside, I think a lot of saw blades (and plier teeth) are laser treated to case harden them rather than a soak and quench type process.i don't know whether this translates to multitool components too, or just dedicated tools.

                                              Tl:dr = dunno :shrug:

                                              1 Reply Last reply

                                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                              With your input, this post could be even better 💗

                                              Register Login

                                              • 1
                                              • 2
                                              1. Home
                                              2. Tool Talk
                                              3. General Tool Discussion
                                              4. Are multitool saws resharpenable?
                                              Reply
                                              • Reply as topic
                                              Log in to reply
                                              COMMUNITY LINKS
                                              EDC-TV SAKWiki GearFeed SAKSelector
                                              Operational Funds

                                              Help us keep the Unworkable working!

                                              Make A Donation
                                              November Goal: $300.00
                                              Due Date: Nov 30
                                              Total Receipts: $0.00
                                              Below Goal: $300.00
                                              0% funded
                                              • Login

                                              • Don't have an account? Register

                                              • Login or register to search.
                                              • First post
                                                Last post
                                              0