Gerber Mr. Pinchy Multi Plier Club
-
Infamously bad Version 1 Multi Plier Scissors. They work on copy paper...sometimes.

inspired by Lynn's scissors thread?
I sure like the MP series' scissors, but never tried the ones in an old Mr.Pinchy!
Indeed.

The shame of it is that the scissors have a decent grind on the cutter portion, but the geometry of cutting causes them to open apart when in use. I tightened the screw on the scissors pivot, but the same issue is there. If the version 1 wasn't a shelf queen, I am certain the pivot screw could be removed and the scissor blades bent slightly to make them more usable. -
Recently got one that in very good condition.. Almost new. But but but.... How do you use these things...? It's like zero handle splay.. I am sure everyone that uses these gets pinch in the palm/fingers and it's no joke... It's built like a tank.... Btw, I notice there's these 2 holes on both sides of the pliers pivot. Are they adjustable? Mine is kinda too tight to be usable.
-
@Sam Lim said:
Recently got one that in very good condition.. Almost new. But but but.... How do you use these things...? It's like zero handle splay.. I am sure everyone that uses these gets pinch in the palm/fingers and it's no joke... It's built like a tank.... Btw, I notice there's these 2 holes on both sides of the pliers pivot. Are they adjustable? Mine is kinda too tight to be usable.And that's why we call them the infamous Mr. Pinchy.

Post a pic and I may be able to help you with the issue at hand. I used one for over ten years! There are three different pivot types. Only one that is an issue is the pliers that slide on rivets instead of screws. If it is a rivet type, then some good silicone oil and a few hours of open/closing may work. If the sliding mechanism has screws, then we're going to get that pinchy working like butter!
If it has the two little holes on each side of the plier pivot, then it is an earlier one with the best pivot and can be adjusted. The four screws that slide the pliers out can be removed for easy adjustment.I found ways to avoid getting pinched a lot. Best thing it to look closely at what you will be using them on and think about where your palm is when squeezing.
-
And avoid cutting anything hard with the wire cutters. When it goes through, the handles close up very rapidly indeed, and hey presto, instant blood blister on your palm !
:ahhh -
@gregozedobe said:
And avoid cutting anything hard with the wire cutters. When it goes through, the handles close up very rapidly indeed, and hey presto, instant blood blister on your palm !
:ahhhIndeed! Those are the best blisters.

When possible cutting hard wire, place 1/2 pinchy handle on hard surface and push down other handle. If no way to push with a hard surface, a piece of plastic sheet or cardboard can be used between your palm and the pinch zone.
I used mine for lamp repair half the time I carried it, so I had systems in place to avoid he pinch.
-
Got a second V. 3 Pinchy in today to replace the one that has a bunch of wear and damage. It'll be put away for sentiment, and this one will be carried once in a blue moon, when the palm feels strong.
Multi Plier with MT.o Patch. by None, on Flickr -
Took the MP out yesterday for "old-time-sake" and had forgotten how to avoid the pinch after not using one for so long. Not a bad pinch, but a pinchy bite nonetheless. Slipped off a 3/8" lamp pipe nut.

Badge please.


-
-
@zoidberg said:
Not quite a blood blister but it is christmas so awarded.
Thank you and Merry Christmas!

Fortunately it wasn't a bad pinchy bite. I've literally burst my skin open two inches long with a pinchy years ago. My palm is much tougher now......thankfully. But wow, the early days of my Mr. Pinchy were brutal. The man I worked for up North used to say "what the smurf" and walk away every time he saw me slip the jaws and get pinched.

-
@gerleatherberman said:
Took the MP out yesterday for "old-time-sake" and had forgotten how to avoid the pinch after not using one for so long. Not a bad pinch, but a pinchy bite nonetheless. Slipped off a 3/8" lamp pipe nut.
Badge please.

Sounds like this tool will have a permanent parking lot on my shelf.

-
The mint BO and SS MPTs arrived. Took group pics with the Multi-Pliers.



-
-
-
-
I believe that this is a "Mr Pinchy" though it has treated me well

I believe that I obtained it in the last 1990s. I have carried it with me almost daily in my briefcase. It also has accompanied me on pre-2001 trips, and on most camping trips.
I am hoping that someone might be able to provide a bit more information about it.
I also have a more recent one with locking tools. It resides in my Subaru.
-
Nice Mr. Pinchy, docfossil! It is a very nice looking version 4 riveted needle nose multi-plier. One of the last ones Gerber produced before the multi-lock.

I have found that regular usage will reduce the likelihood of getting pinched. Thank you for posting! -
Gerleatherberman,
Thanks for the reply and information.
The other thing which I noticed regarding my two Gerber multitools is that the tools on the 1990s version are somewhat primative and not very finished. The screwdrivers, for example, are somewhat rounded. On my more recent version, the tools are much more polished and professional looking.
-
Indeed. Gerber went all out when they moved to the Multi-Lock (Mp600). Nicer drivers, locks, and best of all; they widened the handle spacing to keep people from getting pinched.

The earlier Multi-Plier drivers can be honed on a stone or sandpaper for a more defined profile though. I have done that on mine and it helps the drivers (flat heads) immensely. Much more bite when turning a screw.
-
Picked up my first Gerber with a sliding plier head a few days ago
Iβm usually a Leatherman type of guy, but it sure is fun to play around with
It was in bad condition when I got it, but after some cleaning it works great! The spring tension for the folding tools is kind of bad, so thereβs some wiggle in the lockup though 

-
@Sjoqvist said:
Picked up my first Gerber with a sliding plier head a few days ago
Iβm usually a Leatherman type of guy, but it sure is fun to play around with
It was in bad condition when I got it, but after some cleaning it works great! The spring tension for the folding tools is kind of bad, so thereβs some wiggle in the lockup though 
Congrats on the Gerber multi-plier! Looks to be in nice condition after you worked on it!
The spring retention is an issue on multi-pliers that were well-loved. You can unscrew the button head screw on the tool ends of the handles and remove the tools. Then you can gently(easy...tiny bit at a time ) bend the spring tab in 2-3 millimeters inwards.
Re-install the tools the same way you removed them and put the pivot bolt/screw back in. Oil up and see how you like it.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better π
Register Login