Gerber Mr. Pinchy Multi Plier Club
-
Not quite a blood blister but it is christmas so awarded.

-
@zoidberg said:
Not quite a blood blister but it is christmas so awarded.
Thank you and Merry Christmas!

Fortunately it wasn't a bad pinchy bite. I've literally burst my skin open two inches long with a pinchy years ago. My palm is much tougher now......thankfully. But wow, the early days of my Mr. Pinchy were brutal. The man I worked for up North used to say "what the smurf" and walk away every time he saw me slip the jaws and get pinched.

-
@gerleatherberman said:
Took the MP out yesterday for "old-time-sake" and had forgotten how to avoid the pinch after not using one for so long. Not a bad pinch, but a pinchy bite nonetheless. Slipped off a 3/8" lamp pipe nut.
Badge please.

Sounds like this tool will have a permanent parking lot on my shelf.

-
The mint BO and SS MPTs arrived. Took group pics with the Multi-Pliers. :)


-
Nice collection

-
Nice collection

-
I believe that this is a "Mr Pinchy" though it has treated me well :)
I believe that I obtained it in the last 1990s. I have carried it with me almost daily in my briefcase. It also has accompanied me on pre-2001 trips, and on most camping trips.
I am hoping that someone might be able to provide a bit more information about it.
I also have a more recent one with locking tools. It resides in my Subaru.
-
Nice Mr. Pinchy, docfossil! It is a very nice looking version 4 riveted needle nose multi-plier. One of the last ones Gerber produced before the multi-lock.

I have found that regular usage will reduce the likelihood of getting pinched. Thank you for posting! -
Gerleatherberman,
Thanks for the reply and information.
The other thing which I noticed regarding my two Gerber multitools is that the tools on the 1990s version are somewhat primative and not very finished. The screwdrivers, for example, are somewhat rounded. On my more recent version, the tools are much more polished and professional looking.
-
Indeed. Gerber went all out when they moved to the Multi-Lock (Mp600). Nicer drivers, locks, and best of all; they widened the handle spacing to keep people from getting pinched. :)
The earlier Multi-Plier drivers can be honed on a stone or sandpaper for a more defined profile though. I have done that on mine and it helps the drivers (flat heads) immensely. Much more bite when turning a screw.
-
Picked up my first Gerber with a sliding plier head a few days ago
I’m usually a Leatherman type of guy, but it sure is fun to play around with :D It was in bad condition when I got it, but after some cleaning it works great! The spring tension for the folding tools is kind of bad, so there’s some wiggle in the lockup though 

-
@Sjoqvist said:
Picked up my first Gerber with a sliding plier head a few days ago
I’m usually a Leatherman type of guy, but it sure is fun to play around with :D It was in bad condition when I got it, but after some cleaning it works great! The spring tension for the folding tools is kind of bad, so there’s some wiggle in the lockup though 
Congrats on the Gerber multi-plier! Looks to be in nice condition after you worked on it!
The spring retention is an issue on multi-pliers that were well-loved. You can unscrew the button head screw on the tool ends of the handles and remove the tools. Then you can gently(easy...tiny bit at a time ) bend the spring tab in 2-3 millimeters inwards.
Re-install the tools the same way you removed them and put the pivot bolt/screw back in. Oil up and see how you like it.
-
Picked up my first Gerber with a sliding plier head a few days ago
I’m usually a Leatherman type of guy, but it sure is fun to play around with :D It was in bad condition when I got it, but after some cleaning it works great! The spring tension for the folding tools is kind of bad, so there’s some wiggle in the lockup though 
Congrats on the Gerber multi-plier! Looks to be in nice condition after you worked on it!
The spring retention is an issue on multi-pliers that were well-loved. You can unscrew the button head screw on the tool ends of the handles and remove the tools. Then you can gently(easy...tiny bit at a time ) bend the spring tab in 2-3 millimeters inwards.
Re-install the tools the same way you removed them and put the pivot bolt/screw back in. Oil up and see how you like it.
I see, thanks for the advice! Should I apply heat to the spring when I bend it, or do I mess up the heat treat that way?

-
Picked up my first Gerber with a sliding plier head a few days ago
I’m usually a Leatherman type of guy, but it sure is fun to play around with :D It was in bad condition when I got it, but after some cleaning it works great! The spring tension for the folding tools is kind of bad, so there’s some wiggle in the lockup though 
Congrats on the Gerber multi-plier! Looks to be in nice condition after you worked on it!
The spring retention is an issue on multi-pliers that were well-loved. You can unscrew the button head screw on the tool ends of the handles and remove the tools. Then you can gently(easy...tiny bit at a time ) bend the spring tab in 2-3 millimeters inwards.
Re-install the tools the same way you removed them and put the pivot bolt/screw back in. Oil up and see how you like it.
I see, thanks for the advice! Should I apply heat to the spring when I bend it, or do I mess up the heat treat that way?

I've never had to heat one to get it to move. The spring tab seems to have a poor spring steel treatment from the factory. The only tools I have ever had to bend the tab on were early multi-pliers and two of my early bear jaws MTs. Just be careful and stop bending the tab if it starts to bend too much.

-
It worked well! I also took the time to polish up all the individual implements on the contact surface and applied some oil. Now the tools open butter smooth too! Thanks for the help

-
@Sjoqvist said:
It worked well! I also took the time to polish up all the individual implements on the contact surface and applied some oil. Now the tools open butter smooth too! Thanks for the help
[/quote]
You're welcome! Congrats on getting your Multi-Plier in tip-top shape! They are awesome MTs (aside from the pinchy part) for sure. A lot of tool in a small package.
And being a version 3, the plier head uses a screw and bolt for the pivot. If the pliers ever develope play, they can be tightened very easily. Most MTs have to have the plier peened with a hammer and punch, but the versions 1, 2, & 3 are so much easier to tighten.
-
It worked well! I also took the time to polish up all the individual implements on the contact surface and applied some oil. Now the tools open butter smooth too! Thanks for the help

You're welcome! Congrats on getting your Multi-Plier in tip-top shape! They are awesome MTs (aside from the pinchy part) for sure. A lot of tool in a small package.
And being a version 3, the plier head uses a screw and bolt for the pivot. If the pliers ever develope play, they can be tightened very easily. Most MTs have to have the plier peened with a hammer and punch, but the versions 1, 2, & 3 are so much easier to tighten.
[/quote]Really? You can tighten the pivot with a screw? I learn something every day from you! :D The pliers are just a tad wobbly. I think it’s time to dissasemble the slidy part too
I just have to get myself a hex bit kit with inch instead of my metric ones. I noticed they don’t fit all that well 
I’ve been modifying and rebuilding Leathermans for years, but this Gerber stuff is all new to me

-
A T10 torx driver fits quite snuggly into the hex screws on the plier system as well. :) Once you remove the plier system, one side looks flat and smooth and the other has a specialized nut with the pivot bolt showing. The bolt has two slots on the edges. I use two thin flat head drivers to turn the bolt side a bit.
When taking out the pliers, be careful the spring loaded buttons don't fly away(happened my first time). The last thing I noticed is that the four screws on the sliding system are best put back in the holes you removed them from.
I uaually run the slider screws in to make sure it is the right screw for the hole, and then apply a tiny tiny amount of loctite before re-installing the pliers. If you tighten the slider screws too much, the pliers won't flik out right. Once all the four screws are in, adjust them all to your liking before the loctite sets up. And with that done, you have a practically brand new Gerber Multi-Plier.
-
I see! You don’t happen to know if these tools usually have problems with implements closing ”too far”? The only thing that’s not perfect now is the knife blade. The edge is touching the inside of the handles in closed position and dulling the blade. The blade itself does not look ”worn” near the pivot where the metal should ride against the inside of the handle to keep the edge from touching

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login