Gerber Mr. Pinchy Multi Plier Club
-
And avoid cutting anything hard with the wire cutters. When it goes through, the handles close up very rapidly indeed, and hey presto, instant blood blister on your palm !
:ahhh -
@gregozedobe said:
And avoid cutting anything hard with the wire cutters. When it goes through, the handles close up very rapidly indeed, and hey presto, instant blood blister on your palm !
:ahhhIndeed! Those are the best blisters.

When possible cutting hard wire, place 1/2 pinchy handle on hard surface and push down other handle. If no way to push with a hard surface, a piece of plastic sheet or cardboard can be used between your palm and the pinch zone.
I used mine for lamp repair half the time I carried it, so I had systems in place to avoid he pinch.
-
Got a second V. 3 Pinchy in today to replace the one that has a bunch of wear and damage. It'll be put away for sentiment, and this one will be carried once in a blue moon, when the palm feels strong.
Multi Plier with MT.o Patch. by None, on Flickr -
Took the MP out yesterday for "old-time-sake" and had forgotten how to avoid the pinch after not using one for so long. Not a bad pinch, but a pinchy bite nonetheless. Slipped off a 3/8" lamp pipe nut.

Badge please.


-
-
@zoidberg said:
Not quite a blood blister but it is christmas so awarded.
Thank you and Merry Christmas!

Fortunately it wasn't a bad pinchy bite. I've literally burst my skin open two inches long with a pinchy years ago. My palm is much tougher now......thankfully. But wow, the early days of my Mr. Pinchy were brutal. The man I worked for up North used to say "what the smurf" and walk away every time he saw me slip the jaws and get pinched.

-
@gerleatherberman said:
Took the MP out yesterday for "old-time-sake" and had forgotten how to avoid the pinch after not using one for so long. Not a bad pinch, but a pinchy bite nonetheless. Slipped off a 3/8" lamp pipe nut.
Badge please.

Sounds like this tool will have a permanent parking lot on my shelf.

-
The mint BO and SS MPTs arrived. Took group pics with the Multi-Pliers.



-
-
-
-
I believe that this is a "Mr Pinchy" though it has treated me well

I believe that I obtained it in the last 1990s. I have carried it with me almost daily in my briefcase. It also has accompanied me on pre-2001 trips, and on most camping trips.
I am hoping that someone might be able to provide a bit more information about it.
I also have a more recent one with locking tools. It resides in my Subaru.
-
Nice Mr. Pinchy, docfossil! It is a very nice looking version 4 riveted needle nose multi-plier. One of the last ones Gerber produced before the multi-lock.

I have found that regular usage will reduce the likelihood of getting pinched. Thank you for posting! -
Gerleatherberman,
Thanks for the reply and information.
The other thing which I noticed regarding my two Gerber multitools is that the tools on the 1990s version are somewhat primative and not very finished. The screwdrivers, for example, are somewhat rounded. On my more recent version, the tools are much more polished and professional looking.
-
Indeed. Gerber went all out when they moved to the Multi-Lock (Mp600). Nicer drivers, locks, and best of all; they widened the handle spacing to keep people from getting pinched.

The earlier Multi-Plier drivers can be honed on a stone or sandpaper for a more defined profile though. I have done that on mine and it helps the drivers (flat heads) immensely. Much more bite when turning a screw.
-
Picked up my first Gerber with a sliding plier head a few days ago
Iβm usually a Leatherman type of guy, but it sure is fun to play around with
It was in bad condition when I got it, but after some cleaning it works great! The spring tension for the folding tools is kind of bad, so thereβs some wiggle in the lockup though 

-
@Sjoqvist said:
Picked up my first Gerber with a sliding plier head a few days ago
Iβm usually a Leatherman type of guy, but it sure is fun to play around with
It was in bad condition when I got it, but after some cleaning it works great! The spring tension for the folding tools is kind of bad, so thereβs some wiggle in the lockup though 
Congrats on the Gerber multi-plier! Looks to be in nice condition after you worked on it!
The spring retention is an issue on multi-pliers that were well-loved. You can unscrew the button head screw on the tool ends of the handles and remove the tools. Then you can gently(easy...tiny bit at a time ) bend the spring tab in 2-3 millimeters inwards.
Re-install the tools the same way you removed them and put the pivot bolt/screw back in. Oil up and see how you like it.
-
Picked up my first Gerber with a sliding plier head a few days ago
Iβm usually a Leatherman type of guy, but it sure is fun to play around with
It was in bad condition when I got it, but after some cleaning it works great! The spring tension for the folding tools is kind of bad, so thereβs some wiggle in the lockup though 
Congrats on the Gerber multi-plier! Looks to be in nice condition after you worked on it!
The spring retention is an issue on multi-pliers that were well-loved. You can unscrew the button head screw on the tool ends of the handles and remove the tools. Then you can gently(easy...tiny bit at a time ) bend the spring tab in 2-3 millimeters inwards.
Re-install the tools the same way you removed them and put the pivot bolt/screw back in. Oil up and see how you like it.
I see, thanks for the advice! Should I apply heat to the spring when I bend it, or do I mess up the heat treat that way?

-
Picked up my first Gerber with a sliding plier head a few days ago
Iβm usually a Leatherman type of guy, but it sure is fun to play around with
It was in bad condition when I got it, but after some cleaning it works great! The spring tension for the folding tools is kind of bad, so thereβs some wiggle in the lockup though 
Congrats on the Gerber multi-plier! Looks to be in nice condition after you worked on it!
The spring retention is an issue on multi-pliers that were well-loved. You can unscrew the button head screw on the tool ends of the handles and remove the tools. Then you can gently(easy...tiny bit at a time ) bend the spring tab in 2-3 millimeters inwards.
Re-install the tools the same way you removed them and put the pivot bolt/screw back in. Oil up and see how you like it.
I see, thanks for the advice! Should I apply heat to the spring when I bend it, or do I mess up the heat treat that way?

I've never had to heat one to get it to move. The spring tab seems to have a poor spring steel treatment from the factory. The only tools I have ever had to bend the tab on were early multi-pliers and two of my early bear jaws MTs. Just be careful and stop bending the tab if it starts to bend too much.

-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better π
Register Login