The Hacked Leatherman Owners Club.
-
@Dutch_Tooler said:
Note for Rebar modders: just discovered that the thumb tab of Wave scissors will probably need shortening by about 2 mm to entirely clear the Rebar inner pliers spring in the handle so that it can lie flat and not obstruct the pliers.Sent on my SM-G930F with Tapatalk
I don't remember having to shorten my scissors
I have put them in 2 different Rebars (one for myself and another for my nephew) I will have to check now to be sure :ahhh :D

-
I also didn't have the problem originally, it only arose after I'd put in the Wave file which prompted a reordering of the other tools. YMMV.
Sent on my SM-G930F with Tapatalk
-
Further information which might be useful for swapping tools between Charge, Wave and Rebar and perhaps others:
Tool width in mm, measured with calipers:
Wave/Charge/Rebar range:
Scissors 2.50 **
Large flat screwdriver 2.40
Small flat screwdriver 1.80 *** (can in addition be ground down to an awl for Wave/Charge)
Phillips driver 5.00 *
Large bit driver 5.00
Mini bit driver 2.00
Awl 1.80 ***
Can/package opener 1.90Rebar:
PE blade 1.80
SE blade 1.85
Saw 1.80
File 1.80Wave file 1.85 (just in case a mod is planned... requires profiling a lock cam and slot)
Notes:
- handles and nail nick will need grinding down to fit Wave/Charge
** thumb tab may need shortening for scissors to fit Rebar
*** width and * will need grinding down to fit Wave/Charge
Sent on my SM-G930F with Tapatalk
- handles and nail nick will need grinding down to fit Wave/Charge
-
@Dutch_Tooler said:
Further information which might be useful for swapping tools between Charge, Wave and Rebar and perhaps others:Tool
widththickness in mm, measured with calipers:Wave/Charge/Rebar range:
Scissors 2.50 **
Large flat screwdriver 2.40
Small flat screwdriver 1.80 *** (can in addition be ground down to an awl for Wave/Charge)
Phillips driver 5.00 *
Large bit driver 5.00
Mini bit driver 2.00
Awl 1.80 ***
Can/package opener 1.90Rebar:
PE blade 1.80
SE blade 1.85
Saw 1.80
File 1.80Wave file 1.85 (just in case a mod is planned... requires profiling a lock cam and slot)
Notes:
- handles and nail nick will need grinding down to fit Wave/Charge
** thumb tab may need shortening for scissors to fit Rebar
*** width and * will need grinding down to fit Wave/Charge
Sent on my SM-G930F with Tapatalk

The second "width" is correct though...
- handles and nail nick will need grinding down to fit Wave/Charge
-
All of that information will help modders for sure DT

-
@Dutch_Tooler said:
Thanks Breezy... I think I'll try swapping the heads first, judging by appearances it might just work out without (much) further grinding on the tools- I already did quite a bit of that to make the three new tools fit. Thanks for the tip regarding the blade locks... but I think I'd only consider doing away with that in a real emergency. I had also considered grinding at the pliers head but share your misgivings, especially in view of a fellow member's report on broken pliers...Sent on my SM-G930F with Tapatalk
Did the pliers head swap, i.e. put Rebar pliers into my Wave R. As a result of this I'm considering renaming it to ReWaveR.
Unfortunately, my earlier misgivings have proved correct to an extent. The tool won't close completely because the pliers head hits the inner tools. However, the gap is only 1.5 mm or so and when the tool is closed as far as it goes the blade interlocks in the handles still clear the blade, albeit narrowly. I'm not sure what I should do at this stage, but tend towards leaving it as it is for now.



-
Try filing down the Philip a little to make it a little more "2D". That should work.
-
Yep, thanks, I identified that as an option. Only works one side though...
-
Doesn't look bad the way it is IMO

I wouldn't file down the Phillips that's for sure.
-
Is it the width of the plier heads that is the issue?
-
I think it is the width which is locally greater for the Rebar pliers than for the Wave ones, over a limited portion of their length. The Rebar ones are also less rounded off, although I don't think this is the problem here. The overall thickness is identical for both.
-
That plier head in it still looks great though

-
Thanks

I might try shaving some more material off the flat screwdrivers. That should still be possible without impairing their function...
In other news: Happy New Year!
-
I have filed some material off the flat drivers (small one in shank width, large one made a minute bevel on the upper inner edge as one looks down into the handle, same for the can opener which I took the opportunity to sharpen to lethality) as well as off non-critical parts of the inner handle spring and rivet area. This has reduced the gap, but a small one remains - not due to the Phillips, fortunately, so I won't have to affect its functionality, but the pliers head is now hitting the upward bent part of the handle springs (as measured with the trusty method of a small strip of paper interposed between head and spring and tugging at it until one notices where its stops being held). I am not about to start Dremeling or filing those, so I'll have to live with the remaining gap (about 0.8 mm or so). Not ideal, but after all it's a mod :D.
I am now ready to officially rename it the ReWaveR (note the intended positions of capitals)
!Thanks to all for the tips, and Happy New Year 2018 to all as well

-

Happy New Year to you as well

-
Thanks

Pics in the Showcase thread
-
Happy New Year to all

-
New Year's Day carry - Rebar VX

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
