Access to Power -SOG 30-day Challenge! Starting June 1st! Access & Access Deluxe
-
That’s a shame TP :ahhh :ahhh
Have you got a pic of the braided wire you cut
-
+1!
Side note on the protractor: on my PAD it is almost useless. From eyeball estimates I conclude the indices on the "30/60/180°" sides are off by tens of degrees and the indices do not align with the index on the handle, probably due to misprinting of the indices and/or misdrilling of the hole by which each hinge plate is fixed to the pivots. The "45/90/180°" sides are a bit better. When one index is at the 45° mark the other one is at 30°...

-
These - or similar - are the only hard wire cutters I trust not to deform. I'm almost surprised when MT cutters don't deform. They just are not made to the same hardness and precision as the real thing.
-
Day 2. Tried the saw out on some 1" dowels. The shape of the saw was good for this type of cutting. Not too difficult to push and pull, with the most cutting done on the pull stroke. It does remove material on the push as well, just not nearly as much.
The large teeth didn't try to clog at any point cutting six of the dowel lengths. On the flip side, the large teeth can(and did) cause hand fatigue rather quickly. :ahhh
-
Nice start, guys. Eager to join you in a couple of days!
Sent from my iPhone using Tapatalk
-
Thanks Nix

Have a safe trip and can’t wait to have you joining us
-
Powernoodle Day 3

-
Day 3
Today I had to adjust the fan in the downstairs toilet
It stays on for 30 minutes after you leave the toilet
Which is to long :ahhh
So today I used the jewellers driver
to turn the adjuster down to 10 minutes
The length of the driver helped as the adjuster is set far back in the fan



-
@Wspeed said:
the fan in the downstairs toiletIt stays on for 30 minutes after you leave the toilet
Which is too long :ahhhIf you've ever had some of ThePeacent's cabbage and jalapeno casserole, you'll know that sometimes 30 minutes isn't enough.
Good one

I don’t think any fan would
be strong enough for TPs toilet
:D -
Nothing person, TP. Its that incredible Spanish cuisine.

-
**Day 3 **
From the bathroom to a bedroom. Door handle retainer plate was reported loose. PAD to the rescue. The medium screwdriver on the cap lifter's end is not bad at all, sits well in the screw head slot.
Later tonight I shall use the cap lifter for its intended purpose

Come to think of it, or rather of the can opener: I don't think I have any old-fashioned cans anymore, only those with quick-pull tabs...


Sent on my SM-G930F with Tapatalk
-
I have the same problem with bottles
Most of them now have screw tops
And not the old cap lifter anymore :ahhh :ahhh -
Back to the short saw... I've found a spare ST300 saw in my parts bin which is making me think...


Edit: and the file, too. The ST300's file is both longer and better than the one on the PAD. Hmmm...
Sent on my SM-G930F with Tapatalk
-
@Dutch_Tooler said:
Back to the short saw... I've found a spare ST300 saw in my parts bin which is making me think...
Sent on my SM-G930F with Tapatalk
That looks a lot more usable D_T

Have you got a spare file as well
As that could make the PAD more useful
-
Early pros and cons for me, subject to change:
<u>Pros</u>
- compound leverage pivot is one of the best features on any MT; I knew that a long time ago
- outside opening tools for quick deployment
- real 3D phillips with adequate reach
- it has a saw
- 1/4" driver
- hard wire cutter ate a 10d nail with no problem
<u>Cons</u>
- overall cheap feel
- flimsy main blade; a longer saw could have been used
- tools can accidentally deploy past 180 degrees; no big deal, but not a sign of tight engineering and quality
- file appears to be almost non-functional, but more data is required. Did SOG think we wouldn't notice?
- jewelry driver, can open and cap lifter are unnecessary; space could have been used for scissors
- phillips shank is offset which limits reach in countersunk holes
Current Powernoodle Dynamic Assessment Rating ("CPDAR"): 5/10
-
Cap lifter lifts caps. Had to apply it a second time though, the first time the hook slipped out from under the cap. Operator error can be excluded, it's only my first :D

Sent on my SM-G930F with Tapatalk
-
That’s a shame TP :ahhh :ahhh
Have you got a pic of the braided wire you cut
well, actually yes I have. :D After all the drama to cut that d*rn wire I sure was going to keep it

Next to a Rambler and Spirit for size reference, is just what I had laying on the table

Thanks TP

You would think that it is ok to cut wire
Are you going to send it to SOG for warranty
-
I've been doing outside work today (95 F out and humid) and haven't gotten a chance to use the pad yet, but will be working on something different in a bit and shall use it then. :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
