a couple wave problems
-
Could you send bit more pics on same angle but bit more brighter.
Only tools matters
-
I was going off the assumption, based on his initial post, that the problem wasn't there before he oiled the joints.
I hope I wasn't misinterpreting the original post. :ahhh -
@b_martin said:
I just did a quick forum search and couldn't find an answer to this.. I just gave my wave a cleaning and oiling and now the serrated blade handle doesn't "click" into place when the pliers are open it just slides in and out of place with little force.Put the serrated blade back into the handle when the pliers are closed?

-
Rotating the pivot didn't do anything and I don't see any cracks anywhere. It was a little gritty before I cleaned it, bit it clicked into place. I cleaned some crud and lint out of there. Hopefully this picture is a little better.

-
The gap between the plier head ramp and inside handle seems too far apart.
It is possible, before cleaning, there was a foreign object lodged inside the handle where the plier ramp rotates into place. When you cleaned it, the object may have fallen out, but the damage of it being there, stretching the frame, is still there.I will have to demonstrate what I am talking about with the hammer and punch on a video. Will try to do that tonight or tomorrow. That is, if you decide not to send it to LM for warranty work.
Do you have another MT to use if you have to send the Wave in for repair?
-
@b_martin said:
Rotating the pivot didn't do anything and I don't see any cracks anywhere. It was a little gritty before I cleaned it, bit it clicked into place. I cleaned some crud and lint out of there. Hopefully this picture is a little better.Hi, I so suggest u try to check again. Perhaps use a small screwdriver to try prying. It not obvious and could be hidden under the saw or serrated blade when it's not stressed. See pic for more clarification.. Hope it helps. If nothing works, time to bring out the punch and hammer..


-
@gerleatherberman said:
The gap between the plier head ramp and inside handle seems too far apart.
It is possible, before cleaning, there was a foreign object lodged inside the handle where the plier ramp rotates into place. When you cleaned it, the object may have fallen out, but the damage of it being there, stretching the frame, is still there.I will have to demonstrate what I am talking about with the hammer and punch on a video. Will try to do that tonight or tomorrow. That is, if you decide not to send it to LM for warranty work.
Do you have another MT to use if you have to send the Wave in for repair?
I understand what you mean, I don't really want to send itoff to LM as I don't have a MT to use while it's gone and I'm getting tires of sending tools back to them after the issues I had with my old Rebar
-
@Sam Lim said:
Rotating the pivot didn't do anything and I don't see any cracks anywhere. It was a little gritty before I cleaned it, bit it clicked into place. I cleaned some crud and lint out of there. Hopefully this picture is a little better.
Hi, I so suggest u try to check again. Perhaps use a small screwdriver to try prying. It not obvious and could be hidden under the saw or serrated blade when it's not stressed. See pic for more clarification.. Hope it helps. If nothing works, time to bring out the punch and hammer..
I'll have a better look when I get home from work later
-
By looking that picture theres seems to be dirt what prevents mechanism work correctly. Try clean with pressure air, spraying cleaner or with running water.

Only Tools Matters
-
I just did a quick forum search and couldn't find an answer to this.. I just gave my wave a cleaning and oiling and now the serrated blade handle doesn't "click" into place when the pliers are open it just slides in and out of place with little force.
Put the serrated blade back into the handle when the pliers are closed?

Oops, I missed seeing the word "handle". Now I understand.

That will teach me to MTO late at night.
-
I agree with Antti
, there's a lot of crud around the forked thingies and cleaning that would be my first port of call. -
I may be misunderstanding what is being conveyed here about the dirt in the pivot, so set me straight if I misunderstood.
On the Wave, those prongs don't act as plier locks. They are just to lock the PE and SE blades closed when the pliers are engaged. The plier locking is done via the edge of the ramps, cast into the pliers, against the inside of he handle channel.
One of the handle channels looks as if it were "bowed" outwards. This would cause the lock ramp not to have pressure when the pliers are engaged.
This can happen if a foreign object, such as a piece of metal, got lodged between the ramp and handle channel.Edit: Once the possible foreign object was removed, there was a gap left, with the handle channel bowed out.
-
I'm just saying lets clean the area first. Perhaps the dirt is forcing the prongs to get in the way.

-
So did anything helped, if not could you take pic inside (like above) so we could see is there any abnormality. Pic inside that side what is not working properly

Only Tools Matters
-
Does serrated blade sway when its open? If it does problem may just be loose screws, it affects on handle too if screws are too loose
Only Tools Matters
-
@Antti Lammi said:
Does serrated blade sway when its open? If it does problem may just be loose screws, it affects on handle too if screws are too loose
Only Tools Matters
No, the outside tools on the "good" handle have the same tension as the bad handle. Also, here's another picture
It looks excelent condition, i dont see anything what can cause problem. On my Wave, blade/file handle slides on also and very end when opening it makes little bumb and its then bottom. Handle doesnt open when opening pliers.
Only Tools Matters
-
@Antti Lammi said:
@Antti Lammi said:
Does serrated blade sway when its open? If it does problem may just be loose screws, it affects on handle too if screws are too loose
Only Tools Matters
No, the outside tools on the "good" handle have the same tension as the bad handle. Also, here's another picture
It looks excelent condition, i dont see anything what can cause problem. On my Wave, blade/file handle slides on also and very end when opening it makes little bumb and its then bottom. Handle doesnt open when opening pliers.
Only Tools Matters
Yeah the blade/file handle snaps into place like that, the serrated/saw handle just slides in and out, there's barely any friction. It's all cleaned out and the one handle is still loose. Both sides look identical to one another
-
I wonder, like Gerleathingy already suggested, if the side of the handle has bow'd a bit and just needs a little bit of a tap to push it flat again... not too much though, remember Father Ted...

-
@Fuzzbucket said:
I wonder, like Gerleathingy already suggested, if the side of the handle has bow'd a bit and just needs a little bit of a tap to push it flat again... not too much though, remember Father Ted...Gerleathingy?

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
