Powerlock 30-day challenge
-
Day 22:
Did a bit of yard work this morning. Used the Powerlock to open some bags of compost.......

This evening...and El Peacent has been expecting this, I know...it was roast chicken time!
(Mrs Nix loves roast chicken.)

The Tomahawk is there in case the feeble-feeling blade on the Powerlock wasn't able to meet the task.
However, the Tomahawk was not needed. The SOG's blade did fine. I removed the backbone, the wishbone, the ribs, and spatchcocked the bird.

While the SOG did OK, the blade lost it's edge during this process. In removing the backbone, I tend to 'feel' my way along, severing joints as I go. This results in a little blade-on-bone contact, which seemed to be enough to dull the SOG.
After completing the task, I stropped the SOG to bring the edge right back.
After the chicken was prepped, it was seasoned and grilled for about 45 minutes. Yum!

Thank you, SOG!

(and, yes, I washed the blade after doing yardwork, before cutting up the chicken, and after cutting up the chicken.
) -
Excellent job Nix looks nice

-
@gerleatherberman said:
Thank you for the photos, TP!The saw looks so silly in the BlackTip.

Does your PowerPlier have the saw with fine teeth? Mine does, and the amount of effort to modify the tooling to the newer-style "bigger" teeth would have been a good opportunity to design a new saw especially for the PL. They could have just used the old machinery to make finer-tooth saws for the PP, PPP, and ParaTool. :ahhh
Since I have three PowerPliers (how did I end up with 3 of them? ???) I have what I believe are all the variations, one with the fine smaller teeth, one with the wider and bigger teeth, and one with a Robertson driver instead of a 1/4 driver or an additional Flathead

I haven't compared both saws so I don't really know which would I prefer :ahhh

This evening...and El Peacent has been expecting this, I know...it was roast chicken time!
The Tomahawk is there in case the feeble-feeling blade on the Powerlock wasn't able to meet the task.yes, you knew it :D
To me cauliflower and zucchini testing are essentials to determine the performance of a blade
PS: I once used a Tomahawk in the kitchen (not exactly a tomahawk, it was the Ontario SPAX) and it went through the thing ::) and got stuck into the wooden cutting board below :P, the mark was there for years until we got rid of that board on our last move

-
Day 23:
A few missed photo opportunities today. In the morning I used the large driver bit to pry up the pull-tab on a can of seltzer. So that pretty much saved the day. But no phone or camera, so no glorious action shot.....sorry.
Later, with even more drama, I used the pliers to remove some debris from the engine compartment of Mrs Nix's car. So that was two major rescues in one day, neither of which got documented.
I considered doing some re-enactment shots, but, with the production budget under scrutiny, I opted for a simple nature shot from the garden.

Nice, eh?
So here it is, Day 23, and I have used every tool of the Powerlock, for either it's designed purpose or an alternative, with the exception of the crimper. The rest of this challenge should be pure gravy...........
-
Great pics and uses, Nix!

-
Thanks, G-man.

-
Day 24 :
Time to refill the bird seed bucket.....

-
Nice to see you caring for wildlife Nix

With this hot weather we put
bowls with water out for the wildlife
-
Yes, we've got a big dish of water out near the bird feeders.
The birds love it and we enjoy watching them bathe and drink.

-
Something is a bit fowl about that. :P
Seriously, that is a nice thing to do. I love watching the birds as well. :)
This has been a great challenge thread, Nix! Your photos and uses make me feel lazy. :ahhh
-
G-man, It's not work if you are having fun!
Day 24 (continued):
Used the Powerlock to remove the pins, after test fitting, from a knife I'm finishing up. Pins are tight! And the Powerlock was a great help in pulling them back out.

Knife is epoxied and clamped up now. After the epoxy cures, I'll finish the handle and sharpen up the blade. The blade is one I made from 1095, which is why it's not the most gorgeous thing made. But....should be a nice carry knife.
-
Very nice! I can't wait to see how it comes out!

-
Looking good Nix excellent job

-
Thanks, guys.

There are still many opportunities to make several more mistakes...........

But the epoxy seems to have set up nicely.

-
Day 24 (continued):
Mrs Nix summoned me to go outside this evening. She had discovered some Aspen suckers growing up through a Dogwood shrub and requested they be removed immediately. Well, since the Powerlock was in my pocket.......

I use the wire cutters like secateurs to cut them off, down low. They'll be back, but the Powerlock will still be ready.
-
The SOG wire cutter section is one of the best I know of. Nice job with using them in the yard!

-
Good job Nix

-
@Nix said:
G-man, It's not work if you are having fun!Day 24 (continued):
Used the Powerlock to remove the pins, after test fitting, from a knife I'm finishing up. Pins are tight! And the Powerlock was a great help in pulling them back out.

Knife is epoxied and clamped up now. After the epoxy cures, I'll finish the handle and sharpen up the blade. The blade is one I made from 1095, which is why it's not the most gorgeous thing made. But....should be a nice carry knife.
looks very interesting!!


-
Day 25:
It doesn't pay to get on Mrs Nix's bad side.
Let me explain:
We've had a couple of chipmunks in the local area since Spring. At first they seemed cute. Then they started digging little tunnels and dens under the back patio. But Mrs Nix still thought they were cute.
Then she discovered that at least one chipmunk had gotten up into her car engine compartment and gnawed away some of the insulation under the hood. (Probably to line it's den.) Well, the chipmunks are not cute anymore. I was given orders to remove them from the premises.....ASAP.
So I set out a trap and caught one this morning. He was furious and was chattering and 'barking' at me. I drove him about 10 miles away, to a national forest, with a nice stream nearby.

Now, I've seen Monty Python and I knew I didn't want my fingers anywhere near the mouth of that trap when I opened it up. So, I used the Powerlock to lift up one of the doors from a safe distance away. A good argument for a full-sized multi, right here.
Anyway the little rascal bolted out the trap door and scampered off into the woods. I half-expected him to be back on the patio by the time I got home.

-
Good one Nix

How many more do you have to catch
As there has got to be more than one :ahhh
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
