Project Idea, Need Help
-
I made some little alcohol burners with coke cans so I've cut them open before
Very very light scoring imaging you are drawing a line on the can with a sharpie and lots of turns ;)
What you are left with is quite flimsy and sharp :ahhhLooking forward to seeing how this turns out

-
Ideally you'd need to glue a flange to the can or the top before assembling these. Not sure the seam would hold otherwise...
-
Just another idea how about using a deodorant can instead of a drinks can? not big enough?

You might be able to use the top as a removable lid?One of these things
/post/520211 -
@Sparky415 said:
You can very lightly score the tin under the top edge, keep turning and scoring all the time and the top will almost fall off
Use a Stanley or craft knife
Glue it back on with some epoxy?
Not a lot of surface area for glue

Yep, that work great! Thanks. I will get around to the epoxy part after putting the kit together and buying some epoxy.
MTO_MonsterCan_P1_01 by Grandpa Patch, on Flickr
MTO_MonsterCan_P1_02 by Grandpa Patch, on Flickr -
Doing some online shopping I found this Gorilla Epoxy I've used JB Weld before, but don't think it will work (not clear) and the dispensing of mixtures would just be a mess and tough for the very small rim area that it needs to be applied to. Has anyone used Gorilla Epoxy before that can provide some feedback. Yea/Nea/Something else maybe?
-
@Dutch_Tooler said:
Ideally you'd need to glue a flange to the can or the top before assembling these. Not sure the seam would hold otherwise...As DT says maybe some kind of flange?
This stuff does look good to me

https://www.youtube.com/watch?v=gPCZLIMzvC4 -
Or just get one of those metal flask and put all the stuff in. It will fly under the radar just as well. You can also use the flask for it's intended purpose once you remove the contents. :D
-
Lol, yeah Iād say your turning into a ..

I think someone did post to ditch the credit cards, lol
JR -
Why not keep it super simple and use clear packing tape? Some of that tape is really strong and when you need to open the can you are not dealing with epoxy that could make it really hard to access the goodies inside.

-
Maybe you can glue in a flat ring on the inside (made from the same material) that overlaps the two halves? That would give you a lot more surface area for the glue/epoxy.
A bit hard to explain :) -
I filled in the grove of the outer edge of the cap section with some Loctite Super Glue (ULTRAGEL) and got the cap back onto the can. I let that sit for a couple hours and then went around the outside, bottom side of the top ring of the whole can. The glue can be seen, but I seriously doubt that a casual or even serious look will notice without holding the can and inspecting it. I will let that 'set' for at least 24hr before I fill the can (80%) with water and then glue the cap in place. Then wait another 24 hr before turning it upside down in the sink to check to see if it holds water overnight. If it passes that, then I will shake the can as if it was a new can of spray paint to see how well it holds.
MTO_MCan_01 by Grandpa Patch, on Flickr -
From where I'm sitting it looks a neat job

-
AAAGGGHH!
The photos are no longer available on Flickr.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better š
Register Login