Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Project Idea, Need Help

Scheduled Pinned Locked Moved The Break Room
16 Posts 1 Posters 977 Views
  1. Home
  2. Non Tool Forum
  3. The Break Room
  4. Project Idea, Need Help
Project Idea, Need Help
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • GrandpaPatch Offline
    GrandpaPatch
    Posts: 225
    GrandpaPatch Offline
    GrandpaPatch
    wrote on last edited by
    #6 Quote Reply

      @Sparky415 said:
      You can very lightly score the tin under the top edge, keep turning and scoring all the time and the top will almost fall off
      Use a Stanley or craft knife :tu:

      Glue it back on with some epoxy?
      Not a lot of surface area for glue :shrug:

      :popcorn: :popcorn:

      Yep, that work great! Thanks. I will get around to the epoxy part after putting the kit together and buying some epoxy.
      MTO_MonsterCan_P1_01 by Grandpa Patch, on Flickr
      MTO_MonsterCan_P1_02 by Grandpa Patch, on Flickr

      1 Reply Last reply
      • GrandpaPatch Offline
        GrandpaPatch
        Posts: 225
        GrandpaPatch Offline
        GrandpaPatch
        wrote on last edited by
        #7 Quote Reply

          Doing some online shopping I found this Gorilla Epoxy I've used JB Weld before, but don't think it will work (not clear) and the dispensing of mixtures would just be a mess and tough for the very small rim area that it needs to be applied to. Has anyone used Gorilla Epoxy before that can provide some feedback. Yea/Nea/Something else maybe?

          1 Reply Last reply
          • Sparky415 Offline
            Sparky415
            Posts: 13,000
            Sparky415 Offline
            Sparky415
            wrote on last edited by
            #8 Quote Reply

              @Dutch_Tooler said:
              Ideally you'd need to glue a flange to the can or the top before assembling these. Not sure the seam would hold otherwise...

              As DT says maybe some kind of flange?

              This stuff does look good to me :tu:
              https://www.youtube.com/watch?v=gPCZLIMzvC4

              1 Reply Last reply
              • lister Offline
                lister
                Posts: 1,939
                lister Offline
                lister
                wrote on last edited by
                #9 Quote Reply

                  Or just get one of those metal flask and put all the stuff in. It will fly under the radar just as well. You can also use the flask for it's intended purpose once you remove the contents. :D

                  1 Reply Last reply
                  • MadPlumbarian Offline
                    MadPlumbarian
                    Posts: 38,623
                    MadPlumbarian Offline
                    MadPlumbarian
                    wrote on last edited by
                    #10 Quote Reply

                      Lol, yeah I’d say your turning into a .. :think:
                      I think someone did post to ditch the credit cards, lol
                      JR

                      1 Reply Last reply
                      • Aloha Offline
                        Aloha
                        Global Moderators
                        Posts: 31,235
                        Aloha Offline
                        Aloha
                        Global Moderators
                        wrote on last edited by
                        #11 Quote Reply

                          Why not keep it super simple and use clear packing tape? Some of that tape is really strong and when you need to open the can you are not dealing with epoxy that could make it really hard to access the goodies inside. :dunno:

                          1 Reply Last reply
                          • Reinier Offline
                            Reinier
                            Posts: 10,743
                            Reinier Offline
                            Reinier
                            wrote on last edited by
                            #12 Quote Reply

                              Maybe you can glue in a flat ring on the inside (made from the same material) that overlaps the two halves? That would give you a lot more surface area for the glue/epoxy.
                              A bit hard to explain :)

                              1 Reply Last reply
                              • GrandpaPatch Offline
                                GrandpaPatch
                                Posts: 225
                                GrandpaPatch Offline
                                GrandpaPatch
                                wrote on last edited by
                                #13 Quote Reply

                                  I filled in the grove of the outer edge of the cap section with some Loctite Super Glue (ULTRAGEL) and got the cap back onto the can. I let that sit for a couple hours and then went around the outside, bottom side of the top ring of the whole can. The glue can be seen, but I seriously doubt that a casual or even serious look will notice without holding the can and inspecting it. I will let that 'set' for at least 24hr before I fill the can (80%) with water and then glue the cap in place. Then wait another 24 hr before turning it upside down in the sink to check to see if it holds water overnight. If it passes that, then I will shake the can as if it was a new can of spray paint to see how well it holds.

                                  MTO_MCan_01 by Grandpa Patch, on Flickr

                                  1 Reply Last reply
                                  • Sparky415 Offline
                                    Sparky415
                                    Posts: 13,000
                                    Sparky415 Offline
                                    Sparky415
                                    wrote on last edited by
                                    #14 Quote Reply

                                      From where I'm sitting it looks a neat job :tu:

                                      1 Reply Last reply
                                      • Alan K. Offline
                                        Alan K.
                                        Posts: 8,225
                                        Alan K. Offline
                                        Alan K.
                                        wrote on last edited by
                                        #15 Quote Reply

                                          AAAGGGHH! :rant: The photos are no longer available on Flickr.

                                          1 Reply Last reply

                                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                          With your input, this post could be even better 💗

                                          Register Login

                                          1. Home
                                          2. Non Tool Forum
                                          3. The Break Room
                                          4. Project Idea, Need Help
                                          Reply
                                          • Reply as topic
                                          Log in to reply
                                          COMMUNITY LINKS
                                          EDC-TV SAKWiki GearFeed SAKSelector
                                          Operational Funds

                                          Help us keep the Unworkable working!

                                          Make A Donation
                                          November Goal: $300.00
                                          Due Date: Nov 30
                                          Total Receipts: $0.00
                                          Below Goal: $300.00
                                          0% funded
                                          • Login

                                          • Don't have an account? Register

                                          • Login or register to search.
                                          • First post
                                            Last post
                                          0