Leatherman Free P2/P4 Club and Feedback Thread
-
On my P4 the inside tools opening doesn’t seem to be much of an issue. The P2 inside tools with the file can pop out when using the same force to lock the pliers in place as I use on my Charge. Swinging the handles hasn’t opened either the P4 or P2 tools - it’s when clicking the pliers into place that it happens. If the P2 were mine I’d tighten the pivot but as it is a loaner I’ll leave it alone. I don’t think it’s a safety issue, just annoying on a $120 tool.
On the other hand, my whining about the cost of the tool(s) is a bit ridiculous since I have several Chris Reeve and Hinderer knives. [emoji57]
Sent from my iPad using Tapatalk
-
@gerleatherberman said:
thrilled indeed, Sea Monster. 
To the P2.
I've been sitting around playing with the P2 for a bit. I feel the tool is worth the cost for sure. Not as excited as I hoped to be, but that is my problem, not the tool's. Going forward;
The tool is built very well and the QC is outstanding. The design should be worthy of MT of the year, because of HOW cool the engineering involved is. I have a lot of respect for the design, QC, function, and USA-manufacturing. It isn't going to dethrone my Charge anytime soon(since the magnet would get steel wool dust on them at my job, but I may try it anyway), but it sure is a kickazz tool. Very well made and fun to play with. VERY FUN.Swinging the plier out gently, as is directed will not pop any tools out. At least not on my example. You're supposed to swing the handles out gently and then slowly click the handles into place anyway. I cannot get mine pop any tools out with realistic usage motions.
If you bought one (or thinking of buying one) and are worried about that, just swing it open and pop the pliers into place holding the side with the awl. That'll lessen the momentum incurred by aggressive flipping. The side with the blade is tighter and doesn't really have any possible hazards(the sharp package edge on the flat driver would be almost impossible to get your finger on this way). The blade is blocked from opening when the pliers are engaged, so that won't be an issue. The only tool that would cut you, if you are completely oblivious to using the tool(which tools should always be taken seriously), is the awl. But, that said, it isn't quite as much of an issue as is being worried about here. I hope that helps explain it and possible methods to reduce possible partial opening.
You could always use two security torx bits to tighten the pivot a little, if you're worried about any tools popping open when slipping the pliers or cutting something thick. But, if LM had made the tools tighter, then they wouldn't be easily opened OH and people would be talking about how tight they are. Catch-22.Sidenote: I'll probably regret even posting about getting mine and writing what I think.

P2 pics. They're not very good, since several members have posted gorgeous photos already.



Nice, glad you enjoy it man!
-
@gilson65 said:
Totally agree with your comments especially about the opening method the more I play with mine the more I love it.
Thank you, gilson!

It is quite a unique tool for sure.@gustophersmob said:
Awesome! Glad you like it!
It’s good to know the popping open may not be as big a safety concern as I initially thought. I also didn’t realize the blades were prevented from opening. Good stuff.
As far as metal stuff getting on the magnets, how easy do you think they would be to clean off? Are they pretty easy to access?
Thank you, gustophersmob!

A good quality packing tape could probably get the metal dust off. Luckily the metal doesn't get into the pivot, just onto the retainer magnets. :)@gadgetman7 said:
On my P4 the inside tools opening doesn’t seem to be much of an issue. The P2 inside tools with the file can pop out when using the same force to lock the pliers in place as I use on my Charge. Swinging the handles hasn’t opened either the P4 or P2 tools - it’s when clicking the pliers into place that it happens. If the P2 were mine I’d tighten the pivot but as it is a loaner I’ll leave it alone. I don’t think it’s a safety issue, just annoying on a $120 tool.On the other hand, my whining about the cost of the tool(s) is a bit ridiculous since I have several Chris Reeve and Hinderer knives. [emoji57]
Sent from my iPad using Tapatalk
It is funny. The more I play with it, the more I think the price may be justifiable. It feels refined like a $150 folding knife in certain aspects. But, that said, an incredibly more complex construction is cheaper than some good folders. IMO of course.
Very cool you have the Reeves and Hinderer knives. Some serious bladage there.

Thank you, Monrogue!

Has anyone else noticed that the tools actually DO NOT have true clumping(sorry if I missed someone mentioning that)? The tools all come out when the tangs are pressed as a bunch, BUT, pulling(or using a finger nail individually) each one out, they don't clump. Kind of cool. :)
Edit:
I will say, as far as right now, my only issue is the short file. But, that said, I like the full sized scissors and thin profile as the trade-off. -
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
Really good video on the free p4
-
On my St 300 that's very broken in and opens with a flick the tools always fly out on one side. I tighten the screw but after a while flicking it gets loose again. This also happens on every single SOG with the assisted opening(granted that's only been 3 tools) that I've owned.
-
I had to stop watching that video when he said he couldn't tell the difference in knife edges on the New Wave, because they looked identical.

-
@gerleatherberman said:
I had to stop watching that video when he said he couldn't tell the difference in knife edges on the New Wave, because they looked identical.
seriously, just install the pocket clip and problem solved...there's also gimping on the serrated blade spine, it's really a non issue.
-
@Blackbeard said:
seriously, just install the pocket clip and problem solved...there's also gimping on the serrated blade spine, it's really a non issue.Indeed. I like the guy's approach to the video, but it is obvious he isn't an enthusiast.

-
It is funny. The more I play with it, the more I think the price may be justifiable. It feels refined like a $150 folding knife in certain aspects. But, that said, an incredibly more complex construction is cheaper than some good folders. IMO of course.
How does it go as a knife?
I've found most multis (some more than others - the MP600 can sod right off) have "acceptable" knives for utilitarian tasks, but hardly a pleasure to use - does the P2/P4 have the ergonomics and blade design to really feel like a decent knife in hand? -
Actually. Yes. IMO of course. Sure the handles aren't sculpted for a hand specifically, but the knife setup, as a whole, is outstanding for an MT. It is hard to explain, and maybe someone else can iterate the position better than me.
-
@Sea Monster said:
How does it go as a knife?
I've found most multis (some more than others - the MP600 can sod right off) have "acceptable" knives for utilitarian tasks, but hardly a pleasure to use - does the P2/P4 have the ergonomics and blade design to really feel like a decent knife in hand?In my opinion, the knife is more comfortable than the knife on the Charge. I also like the blade shape better. If they come out with an S30v version, it would be the best knife on any multitool I’ve handled.
Sent from my iPad using Tapatalk
-
@gadgetman7 said:
In my opinion, the knife is more comfortable than the knife on the Charge. I also like the blade shape better. If they come out with an S30v version, it would be the best knife on any multitool I’ve handled.Sent from my iPad using Tapatalk

-
I was thinking about getting a new Charge+ when I saw the reports from SHOT show about the new Free line. The SHOT show videos didn't really give enough information, so I very much appreciate the posts here and the videos linked in these posts. I like the one handedness of the Free models, but I think I'm going to stick with the Charge+. It will be a few weeks before I place an order, so feel FREE to change my mind. Here are my reasons:
The Free P4 and Charge+ cost the same amount.
The Charge+ has a 154CM blade
The Charge+ has both blades easily accessible ( serrated and plain edge ), and right handed
The Charge+ has bit holders
The Charge+ has a longer file, and a diamond coating.The Free has an awl, a better can opener, a package opener, and maybe better scissors.
The Charge has a better plain edge blade, a longer serrated blade, a longer saw, a better file and longer file, and bit drivers.I'm not sold on the 2 and a half D phillips driver, the 420HC plain edge blade, or the funky file. Perhaps there will be a Free P4+ with bit drivers and a diamond file in the future? Anyway, I would love to hear more opinions and will try to keep an eye on this forum. Thanks for all the input so far.
-
Why do they insist on two blades? Ditch the serrated, and have a proper file.
-
I only need one blade on a MT and
a longer file would make much more sense
-
Toss my vote in for the file over SE blade as well. And then put a short SE blade, like the Sidekick, in the tiny file slot. Then swap the giant phillips for a longer, redesigned bit exchanger.
Call it the "Free P-Pro".
-
Sounds like a good MT to me

-
@gerleatherberman said:
Toss my vote in for the file over SE blade as well. And then put a short SE blade, like the Sidekick, in the tiny file slot. Then swap the giant phillips for a longer, redesigned bit exchanger.
Call it the "Free P-Pro".

-
@gerleatherberman said:
Toss my vote in for the file over SE blade as well. And then put a short SE blade, like the Sidekick, in the tiny file slot. Then swap the giant phillips for a longer, redesigned bit exchanger.
Call it the "Free P-Pro".
I like this idea. I’d add the blade exchanger for the saw too.
Sent from my iPad using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login