SAK Spring Questions
-
I didn't read the first question right and I don't have any experience with moving it in to the center.. And by putting the corkscrew with the openers.. Pablo's way is the way to go. That's how he told me to do it and that's what I did
[It's not failure if you learn something from it]
-
@AimlessWanderer said:
Not the answer to the question asked, but attached are pics of the top side and arse end of the Mega84 that I'm carrying this week, which has both backspring Phillips and corkscrew. While these are both on blade layers, it shows that with the cunning use of vacant backspring tool slots, a blade layer can be put where it doesn't belong, and still keep the same aft tool.Genius! I wouldn't have thought of that.
-
@AimlessWanderer said:
Thanks
If you don't want the hook on the back of the scissors, that's one vacant tool slot to work withDeep enough?
-
Incidentally I'm not thinking of doing any filing. I can do plug and play but not much more. :D
-
@kottskrapa said:
There is a sticky with SAK's taken apart so it's easy to compare springs and toolsIt's not a sticky though it should be! :) It looks like the scissors spring can accommodate pretty much anything else on it's rear. Corkscrew, awl, etc. I'd love confirmation though.
-
So I'm thinking of a trying to make a Yeoman with a corkscrew but switching the blade to the centre using the excellent solution of allowing the corkscrew to sit in the gap where the hook would be. I've never used the combo tool, I far prefer a rear can open tool than the regular front opening version but I like the bottle opener on a SAK as a mini pry bar/scraper. Does the Combo tool work as this too? I know it's thinner but my Sharpwerks pry bar works fine and it's pretty thin also. I'd still love to replace the magnifier with something. Can't think of a use for it myself.
-
Or, put in a small blade with the big one and a bottle opener opposite the inline phillips? Forgetting the can opener that I don't like and have never used. Any one know if it's possible to put the bottle opener opposite the phillips on that layer without resorting to tricks? Or would it be better to do it using the opener spring instead of the magnifier spring? I realise I might have to file the bottle opener down slightly so it doesn't hit the phillips but that should be even within my tiny skill set. :) It would have the advantage of only requiring a single donation tool, the Explorer.
-
I'm still waiting for my explorer and pins on the slow boat from the UK (my bro in law hopefully). If anyone has any thoughts about my last question I'd be interested. :D
-
Here it is, ready for the chop.


-
@Don Pablo said:

I've worked out that I have to find a second corkscrew liner to have the corkscrew span two layers (it's actually a bit more, 2.5 layers, has to still stick out the side a bit, it's width is 8mm vs 6mm of two layers). I may have to sacrifice a 2nd hand Spartan. :) I'm also still unsure of how well the bottle opener will work in place of the magnifier or whether I have to use the opener spring and then see if the screwdriver will work in place of the can opener. I won't know till I open them I think. The second option would give me an awl at least. If anyone has any information about that question I'd love to hear from experience!
-
The first pic shows how much of the bottle opener you need to shorten to make it fit with the old-style Phillips. I believe the new style Phillips is shorter, so you don't need to cut as much!

The second pic shows how the bottle opener will sink if you try using it on the Phillips spring... :-\
The third picture shows you how much the Phillips will sink on two opener springs. Looks manageable?




-
@Don Pablo said:
The first pic shows how much of the bottle opener you need to shorten to make it fit with the old-style Phillips. I believe the new style Phillips is shorter, so you don't need to cut as much!
The second pic shows how the bottle opener will sink if you try using it on the Phillips spring... :-\
The third picture shows you how much the Phillips will sink on two opener springs. Looks manageable?

First of all, thank you, that's a huge help! Here is a photo of my explorer, I don't think I'll have to remove much off the bottle opener which is useful.

-
The problem I hadn't thought of is the difference in width. Not sure how to deal with that. Perhaps if I put the bottle opener on the screwdriver layer with a spacer of some kind and some solder on the spring underneath to keep it propped up? I really want to keep it at 3 layer thickness.
You have to forgive me, I'm not very good at this kind of thing.
-
Just measured, the difference in width between the magnifier and the bottle opener is 0.5mm (though the spring width difference is a full mm), that should be easy to achieve with a spacer?
-
Thank you for all the photos, I too am interested in this.
Just for reference sake, I did a quick comparison between pretty old screw drivers(from a swisschamp with fluted corkscrew) vs a new screwdriver.
The new inline phillips sit about 1mm higher than the can opener, and the older one is almost 5mm longer than the new one(which is significant)
-
All along I was thinking to put both bottle opener/can opener side-by-side(opposite to inline phillips), like what Syph usually do on a 93mm mod...is that not achievable with dual opener springs or phillps spring?

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

