SAK Spring Questions
-
So I'm thinking of a trying to make a Yeoman with a corkscrew but switching the blade to the centre using the excellent solution of allowing the corkscrew to sit in the gap where the hook would be. I've never used the combo tool, I far prefer a rear can open tool than the regular front opening version but I like the bottle opener on a SAK as a mini pry bar/scraper. Does the Combo tool work as this too? I know it's thinner but my Sharpwerks pry bar works fine and it's pretty thin also. I'd still love to replace the magnifier with something. Can't think of a use for it myself.
-
Or, put in a small blade with the big one and a bottle opener opposite the inline phillips? Forgetting the can opener that I don't like and have never used. Any one know if it's possible to put the bottle opener opposite the phillips on that layer without resorting to tricks? Or would it be better to do it using the opener spring instead of the magnifier spring? I realise I might have to file the bottle opener down slightly so it doesn't hit the phillips but that should be even within my tiny skill set. :) It would have the advantage of only requiring a single donation tool, the Explorer.
-
I'm still waiting for my explorer and pins on the slow boat from the UK (my bro in law hopefully). If anyone has any thoughts about my last question I'd be interested. :D
-
Here it is, ready for the chop.


-
@Don Pablo said:

I've worked out that I have to find a second corkscrew liner to have the corkscrew span two layers (it's actually a bit more, 2.5 layers, has to still stick out the side a bit, it's width is 8mm vs 6mm of two layers). I may have to sacrifice a 2nd hand Spartan. :) I'm also still unsure of how well the bottle opener will work in place of the magnifier or whether I have to use the opener spring and then see if the screwdriver will work in place of the can opener. I won't know till I open them I think. The second option would give me an awl at least. If anyone has any information about that question I'd love to hear from experience!
-
The first pic shows how much of the bottle opener you need to shorten to make it fit with the old-style Phillips. I believe the new style Phillips is shorter, so you don't need to cut as much!

The second pic shows how the bottle opener will sink if you try using it on the Phillips spring... :-\
The third picture shows you how much the Phillips will sink on two opener springs. Looks manageable?




-
@Don Pablo said:
The first pic shows how much of the bottle opener you need to shorten to make it fit with the old-style Phillips. I believe the new style Phillips is shorter, so you don't need to cut as much!
The second pic shows how the bottle opener will sink if you try using it on the Phillips spring... :-\
The third picture shows you how much the Phillips will sink on two opener springs. Looks manageable?

First of all, thank you, that's a huge help! Here is a photo of my explorer, I don't think I'll have to remove much off the bottle opener which is useful.

-
The problem I hadn't thought of is the difference in width. Not sure how to deal with that. Perhaps if I put the bottle opener on the screwdriver layer with a spacer of some kind and some solder on the spring underneath to keep it propped up? I really want to keep it at 3 layer thickness.
You have to forgive me, I'm not very good at this kind of thing.
-
Just measured, the difference in width between the magnifier and the bottle opener is 0.5mm (though the spring width difference is a full mm), that should be easy to achieve with a spacer?
-
Thank you for all the photos, I too am interested in this.
Just for reference sake, I did a quick comparison between pretty old screw drivers(from a swisschamp with fluted corkscrew) vs a new screwdriver.
The new inline phillips sit about 1mm higher than the can opener, and the older one is almost 5mm longer than the new one(which is significant)
-
All along I was thinking to put both bottle opener/can opener side-by-side(opposite to inline phillips), like what Syph usually do on a 93mm mod...is that not achievable with dual opener springs or phillps spring?

-
@comis said:
All along I was thinking to put both bottle opener/can opener side-by-side(opposite to inline phillips), like what Syph usually do on a 93mm mod...is that not achievable with dual opener springs or phillps spring?
On a 93mm, Syph flips one of the springs around, so that an end for a bottle opener, and an end for a can opener, are on the same end of the knife, if you can visualise what I mean.
That way, he can put the bottle opener and can opener side-by-side.
You can't do that on a 91mm, because unlike 93mm, the pin locations are not symmetrical. -
Hi folks,
Update! Finally got started, going really well so far! I have the scissors on the outside with corkscrew on their back (isn't a perfect fit with the corkscrew, spring isn't designed for it, but certainly good enough). The two blades are centre line with the awl on the back of them. My problem is with the next layer as shown (and predicted by the Don). Getting a spacer isn't the problem (going to use the spacer from the small blade donated by a spartan), neither are the lengths, they work fine. It's getting the bottle opener up sufficiently for opening on a spring designed to let it droop down all the way.
Here is a pic showing the problem:

Proof of solution concept using match sticks

With the 'solution' the nail nicks line up perfecty.

I do wish however that I had a better long term solution than matchsticks! Incidentally I need to do the same thing for the awl, it drops down under the liners with the blade spring. Any ideas at all? Should I find some metal and file it down then stick it in place or is there a better/easier option to be had?
Thanks!
-
A friend suggested sugru but it's hard to get it perfectly sized in time. I was thinking some kind of plastic which I can shave to size?
-
I don't know whether this will help, but do you think it is possible to make a hole on the outside liner, then peen a rivet spacer right under the flathead, then on the other side of the liner, just peen it as flat as possible and make minor changes to the scale?
-
@comis said:
I don't know whether this will help, but do you think it is possible to make a hole on the outside liner, then peen a rivet spacer right under the flathead, then on the other side of the liner, just peen it as flat as possible and make minor changes to the scale?You're assuming I have a drill :D
I did this in the end, cut up a bike wheel spoke and super glued the pieces in. It's a drop high, I'm filing down the 'kick' of the bottle opener at present.

-
This is satisfying and I can't wait for the results! I really enjoy reading and seeing pics of people solving problems
[It's not failure if you learn something from it]
-
Here it goes folks. Just needs to be sharpened back up now. Oh and the custom scales I ordered for it haven't arrived yet, these are some old nylon scales for the moment.

3 layer, blades centre line, inline screwdriver. Pretty much my perfect urban SAK EDC.
I'm happy about most of it. The bottle opener sits a drop high but isn't uncomfortable in hand. The biggest 'problem' is the scissors layer. It doesn't sit well with the corkscrew which sits a bit proud but again not enough to dig into the hand. I didn't realise prior to dismantling but the hook creates the correct strain on the scissors spring to provide the snap. Without the hook it closes lazily unless the corkscrew is open. Again, not enough to be any problem in use. I'm sure someone with the skill set could modify the spring to fix both problems but I did the entire mod using the bottle opener on a 111mm, my LM Charge pliers/file and a hammer. Hardly high tech. :D
What will I do next time? I'd probably keep the blades where they belong (on the side) with the corkscrew and put the awl on the scissors layer. I'd also be a drop more careful with my spacer under the bottle opener for a more precise fit.
-
Nice work and Awsome mod!
[It's not failure if you learn something from it]
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login