Leatherman Free P2/P4 Club and Feedback Thread
-
@gerleatherberman said:
For LM customer support.Yep. I've just sent a mail too; after all I bought my P4 in the US, albeit at BladeHQ. Let's see if they send me one too (to my home address as I'll be flying back day after tomorrow)...
-

I am hoping they will. Bet they don't sell premium tools without the clip included again.
The $120 Charge comes with an optional clip and lanyard. The Free Ps should have included the same options, now that I think about it.

-
Hmm, i'm going to stress Leatherman again, about that pocket clip.
This is my experience regardin reassembly. -
@Raoul Octav said:
Hmm, i'm going to stress Leatherman again, about that pocket clip.
This is my experience regardin reassembly.Good video, Raoul! :like:
That is definitely going to be helpful to people. I like your pliers-removed method of stacking. :salute:
-
My quick and dirty magnet replacement video. It's awful, but I don't have the life force left this evening to remake it. :rofl:
If anyone wants, I'll remake the video using the correct tools(like angle pick, soft tip pliers, etc) at some point. I just used what I had at my desk for the video.
Note: The springs are difficult to damage, but be careful to not put too much force in pulling them upwards to remove the magnet. You only need them to be raised just a bit to slide each side out one at a time. And always make sure the magnet polarity is correct. Also make sure the scissors spring is seated with the two "bumps" placed into the main scissors implement.
-
What's the centre-to-centre distance between the plier pivots? I am interested to see how it compares with other tools.
It looks to be about 18mm on my Surge. -
@gerleatherberman good to know, seems a little to much of a hassle tough.
I wonder why LMN did not put some extra washers.
On one side they did, altough one is missing, and on the other side they didn't put any.
Curtesy of SteveC, i altered the pic to stress the missing washers which would make the opening much smoother.
-
Who has an inside man to help me get a Pocket Clip, courtesy of LMN, as i have a P4 ?
Because, this is the response i got :
Good Morning,
I am happy you were able to get that P4 so quickly. When it comes to the pocket clip, as they are being sold on Leatherman.com now with the pocket clip, customers in the US and Canada, only, who have already purchased them are receiving them as a one time courtesy when they contact us for one.
Kind Regards,

-
@Syncop8r said:
What's the centre-to-centre distance between the plier pivots? I am interested to see how it compares with other tools.
It looks to be about 18mm on my Surge.Will post that in a bit. :)
@Raoul Octav said:
@gerleatherberman good to know, seems a little to much of a hassle tough.
I wonder why LMN did not put some extra washers.
On one side they did, altough one is missing, and on the other side they didn't put any.
Curtesy of SteveC, i altered the pic to stress the missing washers which would make the opening much smoother.Thanks, man!

It is a small hassle, but when not making a video, the magnet swap takes about 2 minutes, where a full break down and reassembly takes 5-8 minutes. The method I posted also reduces the possibility of any parts going rogue across the room(like the little washers and screws. :ahhh -
The more I see the blade the more I am digging the profile of it

-
@gerleatherberman said:
I pushed extremely hard on all of the tabs in my Ps and none of them broke and barely flexed. I think this is not going to be a common problem. The 420HC they used for the handles on the Ps is quite strong, even at the 'weak' areas.
Just checked on mine, next to no give on the tabs (although undated). May have been just a production fluke on that P2...
-
@Dutch_Tooler said:
Just checked on mine, next to no give on the tabs (although undated). May have been just a production fluke on that P2...Very good.

The more I mess with the P4, the more I like it. And it isn't, because it is that great of a tool. I just really like the completely different execution of a useful MT.

-
Hey good news TG!
LM Belgium never replied to my exact same question about the LE PST...
Nothing at all...I think the LM branch here just sips coffee all day on the profits of the hard working folks in the USA.
-
@Mechanickal said:
Hey good news TG!LM Belgium never replied to my exact same question about the LE PST...
Nothing at all...I think the LM branch here just sips coffee all day on the profits of the hard working folks in the USA.
I think we should take over ...

-
@Top-Gear-24 said:
I think we should take over ...
I think we'd rock at our job 8)
Their job... -
After a couple of days of light use:
Pros:
- well constructed
- main blade has a surprisingly solid, beefy feel
- pocket clip and nice sheath
- magnet and free-swinging handles
- plain edge blade, serrated blade, saw and scissors seem of good quality
- replaceable cutters, nice plier head
- long shank on phillips
- looks pretty nice
- smooth on the hand when using the pliers
- outside-opening tools. Finally.
Cons:
- price; repeat this 32 times
- the deployment of the exterior tools seems very gimmicky and unnatural to me. Whether pushing the thumb forward, sideways or toward the palm, it is difficult to deploy the tools and it hurts the thumb. Its impossible to deploy the phillips driver (and whatever that thing is next to it) except by pushing the thumb forward, and even then it is pretty difficult. Its not a deal-breaker, but its close.
- what is that thing next to the phillips? Flat driver? Pry bar? Package opener? Where the heck is the "package opener"?
- no real 3D phillips
- the ruler has to be a prank; you can hear Timmy giggling if you try hard
- the file is teeny weeny, but at least its sharp and well-made
I would like a spring-loaded plier head, but this probably would reduce the strength of the head.
Until I received this, I thought that each tool - like the 2D phillips - was secured with a magnet. I was wrong, but that's on me. The two halves of the tool are secured with magnets.
I knew what I was getting into when I bought this, so no complaints. The price and the tool deployment turn me off, but I had to have one just to satisfy my MT urge. This MT seems to do every okay, and I'm going to carry it for the foreseeable future just to get a better feel for it. I can work my way past the gimmicky tool deployment. But I would not recommend this to anyone because of the exorbitant price and unnatural tool deployment, instead advocating the Wave, Rebar, Spirit, etc. at 50 - 70% of the cost.


-
Thanks for measuring that GLBM.

I'm surprised though, it always looked to me as if it is much further on the Free than on other models. Perhaps it is just that the handles are thinner.
-
@powernoodle said:
After a couple of days of light use:Pros:
- well constructed
- main blade has a surprisingly solid, beefy feel
- pocket clip and nice sheath
- magnet and free-swinging handles
- plain edge blade, serrated blade, saw and scissors seem of good quality
- replaceable cutters, nice plier head
- long shank on phillips
- looks pretty nice
- smooth on the hand when using the pliers
- outside-opening tools. Finally.
Cons:
- price; repeat this 32 times
- the deployment of the exterior tools seems very gimmicky and unnatural to me. Whether pushing the thumb forward, sideways or toward the palm, it is difficult to deploy the tools and it hurts the thumb. Its impossible to deploy the phillips driver (and whatever that thing is next to it) except by pushing the thumb forward, and even then it is pretty difficult. Its not a deal-breaker, but its close.
- what is that thing next to the phillips? Flat driver? Pry bar? Package opener? Where the heck is the "package opener"?
- no real 3D phillips
- the ruler has to be a prank; you can hear Timmy giggling if you try hard
- the file is teeny weeny, but at least its sharp and well-made
I would like a spring-loaded plier head, but this probably would reduce the strength of the head.
Until I received this, I thought that each tool - like the 2D phillips - was secured with a magnet. I was wrong, but that's on me. The two halves of the tool are secured with magnets.
I knew what I was getting into when I bought this, so no complaints. The price and the tool deployment turn me off, but I had to have one just to satisfy my MT urge. This MT seems to do every okay, and I'm going to carry it for the foreseeable future just to get a better feel for it. I can work my way past the gimmicky tool deployment. But I would not recommend this to anyone because of the exorbitant price and unnatural tool deployment, instead advocating the Wave, Rebar, Spirit, etc. at 50 - 70% of the cost.


Great write up, Powernoodle! Thank you for taking the time to do that.

Will be looking forward to reading how the P4 handles your day-to-day MT needs.

-
@Syncop8r said:
Thanks for measuring that GLBM.
I'm surprised though, it always looked to me as if it is much further on the Free than on other models. Perhaps it is just that the handles are thinner.
You're quite welcome, Syncop8r!

I was a bit surprised as well. In fact, I set the calipers back to zero and took the measurement again to double check. It seems your suggestion of the handle geometry plays a role in the visuals.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
