SAK Spring Questions
-
Thank you for all the photos, I too am interested in this.
Just for reference sake, I did a quick comparison between pretty old screw drivers(from a swisschamp with fluted corkscrew) vs a new screwdriver.
The new inline phillips sit about 1mm higher than the can opener, and the older one is almost 5mm longer than the new one(which is significant)
-
All along I was thinking to put both bottle opener/can opener side-by-side(opposite to inline phillips), like what Syph usually do on a 93mm mod...is that not achievable with dual opener springs or phillps spring?

-
@comis said:
All along I was thinking to put both bottle opener/can opener side-by-side(opposite to inline phillips), like what Syph usually do on a 93mm mod...is that not achievable with dual opener springs or phillps spring?
On a 93mm, Syph flips one of the springs around, so that an end for a bottle opener, and an end for a can opener, are on the same end of the knife, if you can visualise what I mean.
That way, he can put the bottle opener and can opener side-by-side.
You can't do that on a 91mm, because unlike 93mm, the pin locations are not symmetrical. -
Hi folks,
Update! Finally got started, going really well so far! I have the scissors on the outside with corkscrew on their back (isn't a perfect fit with the corkscrew, spring isn't designed for it, but certainly good enough). The two blades are centre line with the awl on the back of them. My problem is with the next layer as shown (and predicted by the Don). Getting a spacer isn't the problem (going to use the spacer from the small blade donated by a spartan), neither are the lengths, they work fine. It's getting the bottle opener up sufficiently for opening on a spring designed to let it droop down all the way.
Here is a pic showing the problem:

Proof of solution concept using match sticks

With the 'solution' the nail nicks line up perfecty.

I do wish however that I had a better long term solution than matchsticks! Incidentally I need to do the same thing for the awl, it drops down under the liners with the blade spring. Any ideas at all? Should I find some metal and file it down then stick it in place or is there a better/easier option to be had?
Thanks!
-
A friend suggested sugru but it's hard to get it perfectly sized in time. I was thinking some kind of plastic which I can shave to size?
-
I don't know whether this will help, but do you think it is possible to make a hole on the outside liner, then peen a rivet spacer right under the flathead, then on the other side of the liner, just peen it as flat as possible and make minor changes to the scale?
-
@comis said:
I don't know whether this will help, but do you think it is possible to make a hole on the outside liner, then peen a rivet spacer right under the flathead, then on the other side of the liner, just peen it as flat as possible and make minor changes to the scale?You're assuming I have a drill :D
I did this in the end, cut up a bike wheel spoke and super glued the pieces in. It's a drop high, I'm filing down the 'kick' of the bottle opener at present.

-
This is satisfying and I can't wait for the results! I really enjoy reading and seeing pics of people solving problems
[It's not failure if you learn something from it]
-
Here it goes folks. Just needs to be sharpened back up now. Oh and the custom scales I ordered for it haven't arrived yet, these are some old nylon scales for the moment.

3 layer, blades centre line, inline screwdriver. Pretty much my perfect urban SAK EDC.
I'm happy about most of it. The bottle opener sits a drop high but isn't uncomfortable in hand. The biggest 'problem' is the scissors layer. It doesn't sit well with the corkscrew which sits a bit proud but again not enough to dig into the hand. I didn't realise prior to dismantling but the hook creates the correct strain on the scissors spring to provide the snap. Without the hook it closes lazily unless the corkscrew is open. Again, not enough to be any problem in use. I'm sure someone with the skill set could modify the spring to fix both problems but I did the entire mod using the bottle opener on a 111mm, my LM Charge pliers/file and a hammer. Hardly high tech. :D
What will I do next time? I'd probably keep the blades where they belong (on the side) with the corkscrew and put the awl on the scissors layer. I'd also be a drop more careful with my spacer under the bottle opener for a more precise fit.
-
Nice work and Awsome mod!
[It's not failure if you learn something from it]
-
Good job! It looks pretty good as is
, I look forward to its next evolution! 
-
Nice mod pomsbz
Good to see some different tool configs - nicely done. -
Ingenious!

-
Had a thought of a variation of this mod. Basically a Pioneer X with the big/small blade from a 91mm. I prefer the thinner main blade which don't have the rather noticeable crinking of the Pioneers and I don't need an awl. How possible might that be? Would the blade spring work without something on its back to tension it? I also haven't a clue how to peen the pins on a alox model, how do you do it without wrecking the alox bumps on the handles?
-
Just finished sharpening it up, I don't care what happens, I'm not giving up centre line blades! It's such a joy to use! I've only been carrying single layer pocket knives for that reason. Once the blades move back to centre line it makes such a difference in how easy it is to hold and work with those blades. I'm revising my next version of this build. I'll leave the hook with the scissors and keep the awl on the back of the blades. I use the corkscrew for undoing knots and the awl works for that task if blunted. I'll do this sooner rather than later. I have all the parts including the spare liner and the extra collars I'll probably need by the time I've had the pins drilled out again on this knife. Only annoying thing is that the scales I ordered have the corkscrew slot. In any case it ain't over until the fat lady sings!

-
Glad you like the layout!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
