ZapWizard's Leatherman Free P4 Mods
-
My2cents, maybe focus on a bit adapter for the small bits, the ones used by victorinox cibertool
-
@Raoul Octav said:
My2cents, maybe focus on a bit adapter for the small bits, the ones used by victorinox cibertoolYour referring to 4mm percision bits.
But the Leatherman bits store flat which is really nice. That being said, using 4mm bits would be so so so much cheaper and give the tool access to tons of other proprietary bits. It also opens up a lot more space on the tool because they are smaller than Leatherman bits.Now that you mention it, I'd probably prefer the 4mm bits overall because of how easy they are to replace. A full set, including a spare driver costs less than 10$.
-

Here is the re-designed non-can opener version. It can probably keep the 1/4" hex opening.
I am not quite happy with it. The flat end doesn't look great, but is needed to keep up the material thickness.
@Raoul Octav said:
...maybe focus on a bit adapter for the small bits, the ones used by victorinox cibertool
Since this will be a product mostly for tool modders, that is a good idea. I use a set of 4mm precision bits constantly at work. The only catch is they don't have the larger Torx and screw sizes.
Above is a mock-up image, showing a 4mm bit will fit nicely, and won't require the 5 degree tilt. I may even be able to get the can opener back in.I may be able to develop both at the same time, it would just double my prototyping costs. :-\
-
Here is the re-designed non-can opener version. It can probably keep the 1/4" hex opening.
I am not quite happy with it. The flat end doesn't look great, but is needed to keep up the material thickness.

Since this will be a product mostly for tool modders, that is a good idea. I use a set of 4mm precision bits constantly at work. The only catch is they don't have the larger Torx and screw sizes.
Above is a mock-up image, showing a 4mm bit will fit nicely, and won't require the 5 degree tilt. I may even be able to get the can opener back in.I may be able to develop both at the same time, it would just double my prototyping costs. :-\
Seriously bro, u are amazing. I was going to hold off on the p2 or p4, but you might be forcing me with how awesome these are. I'd do a poll to see which one is more likely to get bought. Sales from one can help offset the other. I do think the 4mm/ bottle opener might be very enticing. Is the 1/4" hex hole still possible with that setup? If so than the 4mm would be better because it's basically a 3 in 1 tool. I'd definitely buy that. Especially since that means it can use the two most common bit shapes. In modding I use the percision bits over the leatherman ones 90% of the time.
-
Interesting option to use the 4mm bits
. That combined with a cap lifter and 1/4" hex would be awesome 
-
That looks excellent ZapWizard

-
@Dutch_Tooler said:
Interesting option to use the 4mm bits
. That combined with a cap lifter and 1/4" hex would be awesome 
A 4mm setup would also likely be stronger because of it's shape. This would also benefit a 1/4" hole.
Imagine if you could add a T-shank exchanger instead of serrated blade. That would let u use the surge saw and file setup..now I'm dreaming
-
that would be great

-
Oh, wow :o Awesome work ZW

-

So I worked last night on the 4mm configuration. I like it enough now that I am ditching the idea of making the flat bit driver, even though I know someone will ask for it eventually.
One thing was getting the bottle opener profile just right. So why not just copy something already known to work? So I copied the Leatherman Brewzer profile. And then tweaked it also work as a 1/4" hex wrench.
There was a bit of dead space in the middle, so I added a horizontal 4mm driver as well.Finally I went through lots of configurations on the magnets. On my first prototyope the magnets installed via a hole at the bottom of the bit driver pocket. However, that meant every time you install a bit, it would slam into the surface of the magnet. And while magnets looks like solid metal, they aren't. They are nickel plated, sintered powder. And cracking the nickel surface can cause the magnet to break up.
I tried some side-loading magnet ideas, but they were both ugly, and didn't allow you to ream out the hole using a drill bit. (The material tolerances can vary a bit)
So instead the magnets install via a deep hole opposite the main bit opening. There is a 1mm thick wall of metal between the magnet and the bit to ensure the bit never strikes the magnet.
Because the hole is deep, you can stack two magnets to increase the overall holding strength.Finally, the hole allowed me to add a 4mm bit driver opening that is accessible even if the tool is fully closed.
I am happy with the design, and will work on getting it prototyped soon.
-
That looks excellent

-
Very cool, Zap 8)

-
Make sure you have a P2 version of the holster and bit holder!
Sent from my iPhone using Tapatalk
-
@Wpgwave said:
Make sure you have a P2 version of the holster and bit holder!The P4 holster will not fit the P2. The P2 is thinner, and has some other subtle changes that would make it so I have to design its own (similar) holster. At $120 for the P2, it too much for right now.
The bit holder should work in either model.



Here is the renderings of the design. It will take a few prototypes to tweak the tolerances, so it won't be out for a few weeks.
-
@ZapWizard said:
The P4 holster will not fit the P2. The P2 is thinner, and has some other subtle changes that would make it so I have to design its own (similar) holster. At $120 for the P2, it too much for right now.
The bit holder should work in either model.



Here is the renderings of the design. It will take a few prototypes to tweak the tolerances, so it won't be out for a few weeks.
Truly incredible..one nitpick though, would it be possible to have some kind of stop for the 4mm hole you have perpendicular to the tool? In other words having it so that the bits didn't go all the way through. Might be too hard with the tool thickness but maybe I'm wrong. Incredible job though.
I think going with the 4mm bits is a really really good idea. It also reduces the likelihood of Leatherman getting really annoyed with it since it doesn't use their flat bit system.
Replacing a single flat bit from Leatherman is a total pain but for $10 you can get something like this:

the extenders and flexable heads would even be usable with the tool you are making.
We're u still able to keep the 4mm hole open to be used while closed? If so that's uterly brilliant design.
-
That looks excellent

-
@Happy Gilmore said:
Would it be possible to have some kind of stop for the 4mm hole you have perpendicular to the tool?We're u still able to keep the 4mm hole open to be used while closed?


Any stop I added to the horizontal wrench would lessen the amount of usable length, or make it usable on one side only. Instead, imagine just putting your finger on the backside, like you might do with a box wrench.
Yes, the deep hole in which you install the magnets into opens up into a second 4mm hex opening at the back.
-
Love your work...
Before I order, I was thinking of getting the mid mount "Large" size and adding the TheClip.com, Model 661BP
Would that fit ok?
Select "Large" for: Tek Lok compatible hole placement.
..
Can also attach to other mid-mount Chicago screw style products.Designed to be compatible with the TheClip.com, Model 661BP
Recommend Tandy Leather, Screw Post Model 1296-04 -

Any stop I added to the horizontal wrench would lessen the amount of usable length, or make it usable on one side only. Instead, imagine just putting your finger on the backside, like you might do with a box wrench.
Yes, the deep hole in which you install the magnets into opens up into a second 4mm hex opening at the back.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login