Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

ZapWizard's Leatherman Free P4 Mods

Scheduled Pinned Locked Moved Leatherman Tools
513 Posts 1 Posters 158.5k Views
  1. Home
  2. Tool Talk
  3. Leatherman Tools
  4. ZapWizard's Leatherman Free P4 Mods
ZapWizard's Leatherman Free P4 Mods
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • ZapWizard Offline
    ZapWizard
    Posts: 171
    ZapWizard Offline
    ZapWizard
    wrote on last edited by
    #49 Quote Reply

      The Nylon is solid but still absorbent. As all nylon materials are. The surface is a bit more so just due to the sintering process this will smooth out quickly. Then be easier to clean. But sealing it with a clear coat or super glue should work.

      The Nylon also has a higher melting point than the softening point of super glue. So if you want to remove them you can try heating the glass surface gently to release the glue. Similar to how folks use CA glue to hold items onto a lathe plate.

      1 Reply Last reply
      • gerleatherberman Offline
        gerleatherberman
        Posts: 10,565
        gerleatherberman Offline
        gerleatherberman
        wrote on last edited by
        #50 Quote Reply

          Many thanks, ZapWizard! :salute:

          1 Reply Last reply
          • ZapWizard Offline
            ZapWizard
            Posts: 171
            ZapWizard Offline
            ZapWizard
            wrote on last edited by
            #51 Quote Reply

              Okay, I have my prototype bit holder modification. Reminder: This uses a 3D printed piece and a magnet to hold the Leatherman Flat Hex interchangeable bits


              The good news: The bottle opener works great. :D

              The sintered stainless steel material is very strong. It took several minutes of drilling to ream out the 1/4" deep magnet hole to fit the magnet just right. I have no doubt it will hold up to some heavy torque.
              The surface is pitted, as a result of the sintering process. But the surface is polished and actually quite low friction. There will be no issues deploying the tool (once the profile is tweaked, more on that later)


              The bad news: The bottle opener cutout makes holding a bit straight impossible. >:(


              The magnet inside does a good job of holding the bit in, but not straight. It can easily tilt away. I will have to skip my precious Topo Chico, or find another solution.
              The internal magnet also doesn't interact with the tool catch magnet at all, so no worries there. The stainless steel is attractive enough to hold close the same as the other tools.


              I made the prototype as a way to test the tolerances of the material, as well as the general fit and strength.
              I did screw up, in that I followed the profile of the blades, and not the other tools. You can see this in the image above, the blade have a more difficult to deploy profile, while the smaller tools have more of a curve to make them easier to deploy.
              Right now the open latch effect isn't as solid as I want. So I will have some re-designs and another prototype or two.


              There are a few options to preserve the bottle opener:
              -Modify the can-opener tool to work as a bottle opener (Like the Wave does)
              -Make a can-opener bit. (I sort of am leaning towards this one)
              -Try to figure out some other placement for it on the bit holder (will work on this also)

              1 Reply Last reply
              • ZapWizard Offline
                ZapWizard
                Posts: 171
                ZapWizard Offline
                ZapWizard
                wrote on last edited by
                #52 Quote Reply

                  The video on the holtser is now live:

                  - YouTube

                  Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.

                  favicon

                  (www.youtube.com)

                  1 Reply Last reply
                  • Raoul Octav Offline
                    Raoul Octav
                    Posts: 417
                    Raoul Octav Offline
                    Raoul Octav
                    wrote on last edited by
                    #53 Quote Reply

                      My2cents, maybe focus on a bit adapter for the small bits, the ones used by victorinox cibertool

                      1 Reply Last reply
                      • Happy Gilmore Offline
                        Happy Gilmore
                        Posts: 1,065
                        Happy Gilmore Offline
                        Happy Gilmore
                        wrote on last edited by
                        #54 Quote Reply

                          @Raoul Octav said:
                          My2cents, maybe focus on a bit adapter for the small bits, the ones used by victorinox cibertool

                          Your referring to 4mm percision bits.
                          But the Leatherman bits store flat which is really nice. That being said, using 4mm bits would be so so so much cheaper and give the tool access to tons of other proprietary bits. It also opens up a lot more space on the tool because they are smaller than Leatherman bits.

                          Now that you mention it, I'd probably prefer the 4mm bits overall because of how easy they are to replace. A full set, including a spare driver costs less than 10$.

                          1 Reply Last reply
                          • ZapWizard Offline
                            ZapWizard
                            Posts: 171
                            ZapWizard Offline
                            ZapWizard
                            wrote on last edited by
                            #55 Quote Reply

                              Here is the re-designed non-can opener version. It can probably keep the 1/4" hex opening.
                              I am not quite happy with it. The flat end doesn't look great, but is needed to keep up the material thickness.


                              @Raoul Octav said:
                              ...maybe focus on a bit adapter for the small bits, the ones used by victorinox cibertool

                              Since this will be a product mostly for tool modders, that is a good idea. I use a set of 4mm precision bits constantly at work. The only catch is they don't have the larger Torx and screw sizes.
                              Above is a mock-up image, showing a 4mm bit will fit nicely, and won't require the 5 degree tilt. I may even be able to get the can opener back in.

                              I may be able to develop both at the same time, it would just double my prototyping costs. :-\

                              1 Reply Last reply
                              • Happy Gilmore Offline
                                Happy Gilmore
                                Posts: 1,065
                                Happy Gilmore Offline
                                Happy Gilmore
                                wrote on last edited by
                                #56 Quote Reply

                                  @ZapWizard said:

                                  Here is the re-designed non-can opener version. It can probably keep the 1/4" hex opening.
                                  I am not quite happy with it. The flat end doesn't look great, but is needed to keep up the material thickness.


                                  Since this will be a product mostly for tool modders, that is a good idea. I use a set of 4mm precision bits constantly at work. The only catch is they don't have the larger Torx and screw sizes.
                                  Above is a mock-up image, showing a 4mm bit will fit nicely, and won't require the 5 degree tilt. I may even be able to get the can opener back in.

                                  I may be able to develop both at the same time, it would just double my prototyping costs. :-\

                                  Seriously bro, u are amazing. I was going to hold off on the p2 or p4, but you might be forcing me with how awesome these are. I'd do a poll to see which one is more likely to get bought. Sales from one can help offset the other. I do think the 4mm/ bottle opener might be very enticing. Is the 1/4" hex hole still possible with that setup? If so than the 4mm would be better because it's basically a 3 in 1 tool. I'd definitely buy that. Especially since that means it can use the two most common bit shapes. In modding I use the percision bits over the leatherman ones 90% of the time.

                                  1 Reply Last reply
                                  • Dutch_Tooler Offline
                                    Dutch_Tooler
                                    Posts: 4,434
                                    Dutch_Tooler Offline
                                    Dutch_Tooler
                                    wrote on last edited by
                                    #57 Quote Reply

                                      Interesting option to use the 4mm bits :tu:. That combined with a cap lifter and 1/4" hex would be awesome :like:

                                      1 Reply Last reply
                                      • Wspeed Offline
                                        Wspeed
                                        Posts: 76,225
                                        Wspeed Offline
                                        Wspeed
                                        wrote on last edited by
                                        #58 Quote Reply

                                          That looks excellent ZapWizard :dd: :like: :like:

                                          1 Reply Last reply
                                          • Happy Gilmore Offline
                                            Happy Gilmore
                                            Posts: 1,065
                                            Happy Gilmore Offline
                                            Happy Gilmore
                                            wrote on last edited by
                                            #59 Quote Reply

                                              @Dutch_Tooler said:
                                              Interesting option to use the 4mm bits :tu:. That combined with a cap lifter and 1/4" hex would be awesome :like:

                                              A 4mm setup would also likely be stronger because of it's shape. This would also benefit a 1/4" hole.

                                              Imagine if you could add a T-shank exchanger instead of serrated blade. That would let u use the surge saw and file setup..now I'm dreaming

                                              1 Reply Last reply
                                              • Wspeed Offline
                                                Wspeed
                                                Posts: 76,225
                                                Wspeed Offline
                                                Wspeed
                                                wrote on last edited by
                                                #60 Quote Reply

                                                  :iagree: that would be great :like: :tu:

                                                  1 Reply Last reply
                                                  • Poncho65 Offline
                                                    Poncho65
                                                    Global Moderators
                                                    Posts: 88,523
                                                    Poncho65 Offline
                                                    Poncho65
                                                    Global Moderators
                                                    wrote on last edited by
                                                    #61 Quote Reply

                                                      Oh, wow :o Awesome work ZW :like: :like:

                                                      1 Reply Last reply
                                                      • ZapWizard Offline
                                                        ZapWizard
                                                        Posts: 171
                                                        ZapWizard Offline
                                                        ZapWizard
                                                        wrote on last edited by
                                                        #62 Quote Reply

                                                          So I worked last night on the 4mm configuration. I like it enough now that I am ditching the idea of making the flat bit driver, even though I know someone will ask for it eventually.

                                                          One thing was getting the bottle opener profile just right. So why not just copy something already known to work? So I copied the Leatherman Brewzer profile. And then tweaked it also work as a 1/4" hex wrench.
                                                          There was a bit of dead space in the middle, so I added a horizontal 4mm driver as well.

                                                          Finally I went through lots of configurations on the magnets. On my first prototyope the magnets installed via a hole at the bottom of the bit driver pocket. However, that meant every time you install a bit, it would slam into the surface of the magnet. And while magnets looks like solid metal, they aren't. They are nickel plated, sintered powder. And cracking the nickel surface can cause the magnet to break up.

                                                          I tried some side-loading magnet ideas, but they were both ugly, and didn't allow you to ream out the hole using a drill bit. (The material tolerances can vary a bit)

                                                          So instead the magnets install via a deep hole opposite the main bit opening. There is a 1mm thick wall of metal between the magnet and the bit to ensure the bit never strikes the magnet.
                                                          Because the hole is deep, you can stack two magnets to increase the overall holding strength.

                                                          Finally, the hole allowed me to add a 4mm bit driver opening that is accessible even if the tool is fully closed.

                                                          I am happy with the design, and will work on getting it prototyped soon.

                                                          1 Reply Last reply
                                                          • Wspeed Offline
                                                            Wspeed
                                                            Posts: 76,225
                                                            Wspeed Offline
                                                            Wspeed
                                                            wrote on last edited by
                                                            #63 Quote Reply

                                                              That looks excellent :dd: :like: :like:

                                                              1 Reply Last reply
                                                              • Poncho65 Offline
                                                                Poncho65
                                                                Global Moderators
                                                                Posts: 88,523
                                                                Poncho65 Offline
                                                                Poncho65
                                                                Global Moderators
                                                                wrote on last edited by
                                                                #64 Quote Reply

                                                                  Very cool, Zap 8) :like:

                                                                  1 Reply Last reply
                                                                  • Wpgwave Offline
                                                                    Wpgwave
                                                                    Posts: 11
                                                                    Wpgwave Offline
                                                                    Wpgwave
                                                                    wrote on last edited by
                                                                    #65 Quote Reply

                                                                      Make sure you have a P2 version of the holster and bit holder!

                                                                      Sent from my iPhone using Tapatalk

                                                                      1 Reply Last reply
                                                                      • Happy Gilmore Offline
                                                                        Happy Gilmore
                                                                        Posts: 1,065
                                                                        Happy Gilmore Offline
                                                                        Happy Gilmore
                                                                        wrote on last edited by
                                                                        #66 Quote Reply

                                                                          @Wpgwave said:
                                                                          Make sure you have a P2 version of the holster and bit holder!

                                                                          Sent from my iPhone using Tapatalk

                                                                          It should be identical for both. And HOLLY MOLLY that looks incredible! :gimme: :gimme: :gimme:

                                                                          1 Reply Last reply
                                                                          • ZapWizard Offline
                                                                            ZapWizard
                                                                            Posts: 171
                                                                            ZapWizard Offline
                                                                            ZapWizard
                                                                            wrote on last edited by
                                                                            #67 Quote Reply

                                                                              @Wpgwave said:
                                                                              Make sure you have a P2 version of the holster and bit holder!

                                                                              The P4 holster will not fit the P2. The P2 is thinner, and has some other subtle changes that would make it so I have to design its own (similar) holster. At $120 for the P2, it too much for right now.
                                                                              The bit holder should work in either model.


                                                                              Here is the renderings of the design. It will take a few prototypes to tweak the tolerances, so it won't be out for a few weeks.

                                                                              1 Reply Last reply
                                                                              • Happy Gilmore Offline
                                                                                Happy Gilmore
                                                                                Posts: 1,065
                                                                                Happy Gilmore Offline
                                                                                Happy Gilmore
                                                                                wrote on last edited by Happy Gilmore
                                                                                #68 Quote Reply

                                                                                  @ZapWizard said:
                                                                                  The P4 holster will not fit the P2. The P2 is thinner, and has some other subtle changes that would make it so I have to design its own (similar) holster. At $120 for the P2, it too much for right now.
                                                                                  The bit holder should work in either model.


                                                                                  Here is the renderings of the design. It will take a few prototypes to tweak the tolerances, so it won't be out for a few weeks.

                                                                                  Truly incredible..one nitpick though, would it be possible to have some kind of stop for the 4mm hole you have perpendicular to the tool? In other words having it so that the bits didn't go all the way through. Might be too hard with the tool thickness but maybe I'm wrong. Incredible job though.

                                                                                  I think going with the 4mm bits is a really really good idea. It also reduces the likelihood of Leatherman getting really annoyed with it since it doesn't use their flat bit system.

                                                                                  Replacing a single flat bit from Leatherman is a total pain but for $10 you can get something like this:

                                                                                  the extenders and flexable heads would even be usable with the tool you are making.

                                                                                  We're u still able to keep the 4mm hole open to be used while closed? If so that's uterly brilliant design.

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  • 3
                                                                                  • 4
                                                                                  • 5
                                                                                  • 25
                                                                                  • 26
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. Leatherman Tools
                                                                                  4. ZapWizard's Leatherman Free P4 Mods
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0