ZapWizard's Leatherman Free P4 Mods
-
Interesting option to use the 4mm bits
. That combined with a cap lifter and 1/4" hex would be awesome 
-
That looks excellent ZapWizard

-
@Dutch_Tooler said:
Interesting option to use the 4mm bits
. That combined with a cap lifter and 1/4" hex would be awesome 
A 4mm setup would also likely be stronger because of it's shape. This would also benefit a 1/4" hole.
Imagine if you could add a T-shank exchanger instead of serrated blade. That would let u use the surge saw and file setup..now I'm dreaming
-
that would be great

-
Oh, wow :o Awesome work ZW

-

So I worked last night on the 4mm configuration. I like it enough now that I am ditching the idea of making the flat bit driver, even though I know someone will ask for it eventually.
One thing was getting the bottle opener profile just right. So why not just copy something already known to work? So I copied the Leatherman Brewzer profile. And then tweaked it also work as a 1/4" hex wrench.
There was a bit of dead space in the middle, so I added a horizontal 4mm driver as well.Finally I went through lots of configurations on the magnets. On my first prototyope the magnets installed via a hole at the bottom of the bit driver pocket. However, that meant every time you install a bit, it would slam into the surface of the magnet. And while magnets looks like solid metal, they aren't. They are nickel plated, sintered powder. And cracking the nickel surface can cause the magnet to break up.
I tried some side-loading magnet ideas, but they were both ugly, and didn't allow you to ream out the hole using a drill bit. (The material tolerances can vary a bit)
So instead the magnets install via a deep hole opposite the main bit opening. There is a 1mm thick wall of metal between the magnet and the bit to ensure the bit never strikes the magnet.
Because the hole is deep, you can stack two magnets to increase the overall holding strength.Finally, the hole allowed me to add a 4mm bit driver opening that is accessible even if the tool is fully closed.
I am happy with the design, and will work on getting it prototyped soon.
-
That looks excellent

-
Very cool, Zap 8)

-
Make sure you have a P2 version of the holster and bit holder!
Sent from my iPhone using Tapatalk
-
@Wpgwave said:
Make sure you have a P2 version of the holster and bit holder!The P4 holster will not fit the P2. The P2 is thinner, and has some other subtle changes that would make it so I have to design its own (similar) holster. At $120 for the P2, it too much for right now.
The bit holder should work in either model.



Here is the renderings of the design. It will take a few prototypes to tweak the tolerances, so it won't be out for a few weeks.
-
@ZapWizard said:
The P4 holster will not fit the P2. The P2 is thinner, and has some other subtle changes that would make it so I have to design its own (similar) holster. At $120 for the P2, it too much for right now.
The bit holder should work in either model.



Here is the renderings of the design. It will take a few prototypes to tweak the tolerances, so it won't be out for a few weeks.
Truly incredible..one nitpick though, would it be possible to have some kind of stop for the 4mm hole you have perpendicular to the tool? In other words having it so that the bits didn't go all the way through. Might be too hard with the tool thickness but maybe I'm wrong. Incredible job though.
I think going with the 4mm bits is a really really good idea. It also reduces the likelihood of Leatherman getting really annoyed with it since it doesn't use their flat bit system.
Replacing a single flat bit from Leatherman is a total pain but for $10 you can get something like this:

the extenders and flexable heads would even be usable with the tool you are making.
We're u still able to keep the 4mm hole open to be used while closed? If so that's uterly brilliant design.
-
That looks excellent

-
@Happy Gilmore said:
Would it be possible to have some kind of stop for the 4mm hole you have perpendicular to the tool?We're u still able to keep the 4mm hole open to be used while closed?


Any stop I added to the horizontal wrench would lessen the amount of usable length, or make it usable on one side only. Instead, imagine just putting your finger on the backside, like you might do with a box wrench.
Yes, the deep hole in which you install the magnets into opens up into a second 4mm hex opening at the back.
-
Love your work...
Before I order, I was thinking of getting the mid mount "Large" size and adding the TheClip.com, Model 661BP
Would that fit ok?
Select "Large" for: Tek Lok compatible hole placement.
..
Can also attach to other mid-mount Chicago screw style products.Designed to be compatible with the TheClip.com, Model 661BP
Recommend Tandy Leather, Screw Post Model 1296-04 -

Any stop I added to the horizontal wrench would lessen the amount of usable length, or make it usable on one side only. Instead, imagine just putting your finger on the backside, like you might do with a box wrench.
Yes, the deep hole in which you install the magnets into opens up into a second 4mm hex opening at the back.

-

@aussieman said:
Before I order, I was thinking of getting the mid mount "Large" size and adding the TheClip.com, Model 661BPYes it will mount the metal clip. Rather than fix the chicago screw positions to just Tek-Lok like I did on the Wave, I decided to make it one fixed hole, and one slot. That way more products can be mounted.
There was a small issue on the Tek-Lok version which might have allowed the bottom edge of the clip to catch, but I updated the 3D model just now. One of the great things about 3D printing is instant changes are possible. -



I 3D printed a mockup of the bit holder in plastic. I shrunk the 3D model by 3% to emulate the shrinkage that the sintered steel will have.
The plastic mock-up isn't strong enough to actually use, but it lets me get an idea of the general use.The mockup showed that I am damn close on the latching profile. The tool folds out and locks almost as good as the metal implements. I little tweak to the model will hopefully make it fully solid.
The 1/4" wrench actually works in only one direction, it is sort of ratcheting. I also did a torque test on my earlier steel prototype and the 1/4" opening on it was extremely strong, i may test it to full distruction at some point)
The mock up also helped me realize that I have some space I am wasting due to the springs on each side. So I altered the profile to be a total of 1.3mm wider, every bit helps with an object this small.Finally, I modified the real hex profile to have a better fit, and ensure the end of the bit wouldn't grind against the chicago screw.
I ordered the bit holder in steel, along with a few other projects I am working on. (Rebar holster)
-


I 3D printed a mockup of the bit holder in plastic. I shrunk the 3D model by 3% to emulate the shrinkage that the sintered steel will have.
The plastic mock-up isn't strong enough to actually use, but it lets me get an idea of the general use.The mockup showed that I am damn close on the latching profile. The tool folds out and locks almost as good as the metal implements. I little tweak to the model will hopefully make it fully solid.
The 1/4" wrench actually works in only one direction, it is sort of ratcheting. I also did a torque test on my earlier steel prototype and the 1/4" opening on it was extremely strong, i may test it to full distruction at some point)
The mock up also helped me realize that I have some space I am wasting due to the springs on each side. So I altered the profile to be a total of 1.3mm wider, every bit helps with an object this small.Finally, I modified the real hex profile to have a better fit, and ensure the end of the bit wouldn't grind against the chicago screw.
I ordered the bit holder in steel, along with a few other projects I am working on. (Rebar holster)
Amazing Work, but honestly I would have removed the tools from the other sided and kept the Philips and pry bar. The 4mm bits really cant apply the torque of those two tools. I'd much rather give up the less robust tools that have questionable strength than the ones I can depend on. but to each their own on this.
I can't wait to see how this thing looks at the end.
-
Looking forward to seeing how strong this turns out to be.@ZapWizard, mind telling us which 3D printer/ plastic (ABS?) you're using? Looks like some neat printing

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login