ZapWizard's Leatherman Free P4 Mods
-



I 3D printed a mockup of the bit holder in plastic. I shrunk the 3D model by 3% to emulate the shrinkage that the sintered steel will have.
The plastic mock-up isn't strong enough to actually use, but it lets me get an idea of the general use.The mockup showed that I am damn close on the latching profile. The tool folds out and locks almost as good as the metal implements. I little tweak to the model will hopefully make it fully solid.
The 1/4" wrench actually works in only one direction, it is sort of ratcheting. I also did a torque test on my earlier steel prototype and the 1/4" opening on it was extremely strong, i may test it to full distruction at some point)
The mock up also helped me realize that I have some space I am wasting due to the springs on each side. So I altered the profile to be a total of 1.3mm wider, every bit helps with an object this small.Finally, I modified the real hex profile to have a better fit, and ensure the end of the bit wouldn't grind against the chicago screw.
I ordered the bit holder in steel, along with a few other projects I am working on. (Rebar holster)
-


I 3D printed a mockup of the bit holder in plastic. I shrunk the 3D model by 3% to emulate the shrinkage that the sintered steel will have.
The plastic mock-up isn't strong enough to actually use, but it lets me get an idea of the general use.The mockup showed that I am damn close on the latching profile. The tool folds out and locks almost as good as the metal implements. I little tweak to the model will hopefully make it fully solid.
The 1/4" wrench actually works in only one direction, it is sort of ratcheting. I also did a torque test on my earlier steel prototype and the 1/4" opening on it was extremely strong, i may test it to full distruction at some point)
The mock up also helped me realize that I have some space I am wasting due to the springs on each side. So I altered the profile to be a total of 1.3mm wider, every bit helps with an object this small.Finally, I modified the real hex profile to have a better fit, and ensure the end of the bit wouldn't grind against the chicago screw.
I ordered the bit holder in steel, along with a few other projects I am working on. (Rebar holster)
Amazing Work, but honestly I would have removed the tools from the other sided and kept the Philips and pry bar. The 4mm bits really cant apply the torque of those two tools. I'd much rather give up the less robust tools that have questionable strength than the ones I can depend on. but to each their own on this.
I can't wait to see how this thing looks at the end.
-
Looking forward to seeing how strong this turns out to be.@ZapWizard, mind telling us which 3D printer/ plastic (ABS?) you're using? Looks like some neat printing

-
@Dutch_Tooler said:
mind telling us which 3D printer/ plastic (ABS?) you're using?The mockup was printed on a Ultmaker 2, 0.4mm nozzle, 0.12mm layers, PLA plastic. It makes very clean prints most of the time. It took about fifteen minutes to dig out all the support material from the internal holes, one of the bad things about FDM printers.
-
Thanks ZapWizard

-
Zapwizard, I have been lurking around for a while and first of all I got to say What an amazing design. And what a beautiful render of the Leatherman P4. Since I use solidworks and inventor myself I know how much work and time such a drawing cost. Really incredible work!
I like the design of the bottle opener/ bit driver a lot too. But I can't help to think about an idea that might improve it.At the moment you can us the standard 1/4 inch at the bottle opener position and the 4mm while closed, while open and from the side. My idea is to replace one of those. I don't know if it is possible but maybe you could replace the 4mm hole from the side with a hole that fits the flat leatherman bits. And therefor make the tool accept the 3 I think most used sizes. Again I don't know if it is possible in ways of strength and space but should it be possible I think it can be a real improvement.
I hope I didn't disrespect you in any way. That is not my intention at all.
Sent from my ONEPLUS A3003 using Tapatalk
-
@jorritvS said:
At the moment you can us the standard 1/4 inch at the bottle opener position and the 4mm while closed, while open and from the side. My idea is to replace one of those. I don't know if it is possible but maybe you could replace the 4mm hole from the side with a hole that fits the flat leatherman bits. And therefor make the tool accept the 3 I think most used sizes. Again I don't know if it is possible in ways of strength and space but should it be possible I think it can be a real improvement.
I could fit a Leatherman bit holder into that space. Mabye even a combination 4mm, flat bit opening. However, someone who picked up a Free P4 without every owning any other Leatherman won't have any bits, or even necessarily know the flat bits exist. I owned a wave for years before I even knew they sold other bits, I just figured I got Phillips and Flathead. Also, the flat bits can be turned in the 1/4" opening. But it isn't ideal, they lock in one direction, and let go easily in the other.
Input and ideas isn't disrespectful at all. This is a two way street, otherwise I would just post to YouTube and ignore all comments.
-
I didn't even thought about combining both flat leatherman and 4mm bits that would be awesome.
The good thing about the flat bits is that they are easy to carry and offer a lot of possibilities.
I understand that not everyone has the leatherman set. But adding the possibility to use can never hurt.
I think a lot of people on the forum have a set for one of the many tools they are designed for. And otherwise can be a good expansion.But maybe I'm the only one who would like it.
Sent from my ONEPLUS A3003 using Tapatalk
-
I could fit a Leatherman bit holder into that space. Mabye even a combination 4mm, flat bit opening. However, someone who picked up a Free P4 without every owning any other Leatherman won't have any bits, or even necessarily know the flat bits exist. I owned a wave for years before I even knew they sold other bits, I just figured I got Phillips and Flathead. Also, the flat bits can be turned in the 1/4" opening. But it isn't ideal, they lock in one direction, and let go easily in the other.
Input and ideas isn't disrespectful at all. This is a two way street, otherwise I would just post to YouTube and ignore all comments.
I think you are really on to something, a Leatherman flat bit slot would actually be better (unless the hole works for both). Using the bit extender would prevent the bits from going straight through. This would let you put a lot more force on a screw. The more I think about it...just go with the Leatherman bits over the 4mm, it will make the slot a lot stronger, and give u access to ALL of the drivers at once. Amazing idea. This basically gives everyone something. I think the Leatherman extender makes that slot so much more usable than if it was 4mm, especially since there are already two 4mm bit insertion points.
-


Today I received the production bit holder, and it is beautiful.
Other than having to ream out the holes a tiny bit, it is perfectly ready to install. (See video) All the bit openings are just right, and the locking action is solid.
I have to think about if I will even add the flat bit driver opening since most people won't have them anyways. I am a bit superstitious about changing a model once something works.
The magnets are strong enough to hold the bit and it won't come out when flicking the holder out, but it isn't as strong as some screwdrivers. If you want it stronger, you can try drilling the 1mm separation to be thinner.
Please help me spread the word on placed like /r/Leatherman, we can show them the product can be improved. -
I got to say it looks amazing. I mostly try to keep a tool as original as possible but this really makes me think twice.
You definitely should have worked for Leatherman during the design process. It looks better/works better/gives more options then the setup they used. We'll done zapwizard!Sent from my ONEPLUS A3003 using Tapatalk
-
That is so very awesome, Zap
You have really done some great work with adding the bit holder
the sheath and it's different clip placements are also great 
-
Excellent work

-
I may need to make one change: The magnets have a 1mm gap of metal that separates them from the bit. Most magnetic screw drivers just let the magnet and bit come into 100% contact, this is why so many of them end up with broken magnets. However due to the inverse square law, the magnetic pull isn't as strong as I want. So I will change the solid 1mm of metal, to a small taper that tries to stop the magnets a bit closer to the tool surface. The danger is if someone needs reams out the hole they might tear though the tapered section and then the magnets can fall out. (Glue is the solution here). I got to think about if it is worth it.
-
What wonderful design and executed very well too! Looking forward to the final product!

-
I ran a few tests to ensure this is up to the task:

The bottle opener works.

The 4mm bit driver handles plenty of torque. The tool body started to bend when I reached 14 in-lbs (1.6 Nm)

The 1/4" wrench handled more than 30 in-lbs (3.4 Nm).
-
This is awesone work Zap

Could I perhaps ask you to consider adding the LM 2D bit slot all the same? Or maybe an alternate model that has this instead of the transversal 4mm hex? I for one have the LM bits, and they make for a reasonably compact carry in the bit card. I'm sure I'm not the only potential buyer that could benefit.
-
about the bits
also that is some great results in the testing as well

-
Excellent testing looks like it can handle some torque

-
@Dutch_Tooler said:
Could I perhaps ask you to consider adding the LM 2D bit slot all the same? Or maybe an alternate model that has this instead of the transversal 4mm hex?It would need to be an alternate model. I tried a few things today in CAD, but it works out to be too thin in critical places if I try to mix both together. I also realized I don't need a mixed horizontal opening, as the 1/4" wrench works well on the flat bits.
I did update the magnet stop to be smaller, this is live on the shop now. I have another batch of things to order, so I will get a new build, this time in a different finish. (The 24K gold plating is pretty, but it flakes off too easy for a tool)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login