Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

ZapWizard's Leatherman Free P4 Mods

Scheduled Pinned Locked Moved Leatherman Tools
513 Posts 1 Posters 158.5k Views
  1. Home
  2. Tool Talk
  3. Leatherman Tools
  4. ZapWizard's Leatherman Free P4 Mods
ZapWizard's Leatherman Free P4 Mods
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • ZapWizard Offline
    ZapWizard
    Posts: 171
    ZapWizard Offline
    ZapWizard
    wrote on last edited by
    #80 Quote Reply

      @jorritvS said:
      At the moment you can us the standard 1/4 inch at the bottle opener position and the 4mm while closed, while open and from the side. My idea is to replace one of those. I don't know if it is possible but maybe you could replace the 4mm hole from the side with a hole that fits the flat leatherman bits. And therefor make the tool accept the 3 I think most used sizes. Again I don't know if it is possible in ways of strength and space but should it be possible I think it can be a real improvement.

      I could fit a Leatherman bit holder into that space. Mabye even a combination 4mm, flat bit opening. However, someone who picked up a Free P4 without every owning any other Leatherman won't have any bits, or even necessarily know the flat bits exist. I owned a wave for years before I even knew they sold other bits, I just figured I got Phillips and Flathead. Also, the flat bits can be turned in the 1/4" opening. But it isn't ideal, they lock in one direction, and let go easily in the other.

      Input and ideas isn't disrespectful at all. This is a two way street, otherwise I would just post to YouTube and ignore all comments.

      1 Reply Last reply
      • jorritvS Offline
        jorritvS
        Posts: 75
        jorritvS Offline
        jorritvS
        wrote on last edited by
        #81 Quote Reply

          I didn't even thought about combining both flat leatherman and 4mm bits that would be awesome.

          The good thing about the flat bits is that they are easy to carry and offer a lot of possibilities.

          I understand that not everyone has the leatherman set. But adding the possibility to use can never hurt.
          I think a lot of people on the forum have a set for one of the many tools they are designed for. And otherwise can be a good expansion.

          But maybe I'm the only one who would like it.

          Sent from my ONEPLUS A3003 using Tapatalk

          1 Reply Last reply
          • Happy Gilmore Offline
            Happy Gilmore
            Posts: 1,065
            Happy Gilmore Offline
            Happy Gilmore
            wrote on last edited by
            #82 Quote Reply

              @ZapWizard said:

              I could fit a Leatherman bit holder into that space. Mabye even a combination 4mm, flat bit opening. However, someone who picked up a Free P4 without every owning any other Leatherman won't have any bits, or even necessarily know the flat bits exist. I owned a wave for years before I even knew they sold other bits, I just figured I got Phillips and Flathead. Also, the flat bits can be turned in the 1/4" opening. But it isn't ideal, they lock in one direction, and let go easily in the other.

              Input and ideas isn't disrespectful at all. This is a two way street, otherwise I would just post to YouTube and ignore all comments.

              I think you are really on to something, a Leatherman flat bit slot would actually be better (unless the hole works for both). Using the bit extender would prevent the bits from going straight through. This would let you put a lot more force on a screw. The more I think about it...just go with the Leatherman bits over the 4mm, it will make the slot a lot stronger, and give u access to ALL of the drivers at once. Amazing idea. This basically gives everyone something. I think the Leatherman extender makes that slot so much more usable than if it was 4mm, especially since there are already two 4mm bit insertion points.

              1 Reply Last reply
              • ZapWizard Offline
                ZapWizard
                Posts: 171
                ZapWizard Offline
                ZapWizard
                wrote on last edited by
                #83 Quote Reply

                  https://youtu.be/RrU_kSBGWFc

                  Today I received the production bit holder, and it is beautiful.

                  Other than having to ream out the holes a tiny bit, it is perfectly ready to install. (See video) All the bit openings are just right, and the locking action is solid.
                  I have to think about if I will even add the flat bit driver opening since most people won't have them anyways. I am a bit superstitious about changing a model once something works.
                  The magnets are strong enough to hold the bit and it won't come out when flicking the holder out, but it isn't as strong as some screwdrivers. If you want it stronger, you can try drilling the 1mm separation to be thinner.
                  Please help me spread the word on placed like /r/Leatherman, we can show them the product can be improved.

                  1 Reply Last reply
                  • jorritvS Offline
                    jorritvS
                    Posts: 75
                    jorritvS Offline
                    jorritvS
                    wrote on last edited by
                    #84 Quote Reply

                      I got to say it looks amazing. I mostly try to keep a tool as original as possible but this really makes me think twice.
                      You definitely should have worked for Leatherman during the design process. It looks better/works better/gives more options then the setup they used. We'll done zapwizard!

                      Sent from my ONEPLUS A3003 using Tapatalk

                      1 Reply Last reply
                      • Poncho65 Offline
                        Poncho65
                        Global Moderators
                        Posts: 88,523
                        Poncho65 Offline
                        Poncho65
                        Global Moderators
                        wrote on last edited by
                        #85 Quote Reply

                          That is so very awesome, Zap :like: You have really done some great work with adding the bit holder :salute: the sheath and it's different clip placements are also great :cheers:

                          1 Reply Last reply
                          • Wspeed Offline
                            Wspeed
                            Posts: 76,225
                            Wspeed Offline
                            Wspeed
                            wrote on last edited by
                            #86 Quote Reply

                              Excellent work :dd: :like: :like:

                              1 Reply Last reply
                              • ZapWizard Offline
                                ZapWizard
                                Posts: 171
                                ZapWizard Offline
                                ZapWizard
                                wrote on last edited by
                                #87 Quote Reply

                                  I may need to make one change: The magnets have a 1mm gap of metal that separates them from the bit. Most magnetic screw drivers just let the magnet and bit come into 100% contact, this is why so many of them end up with broken magnets. However due to the inverse square law, the magnetic pull isn't as strong as I want. So I will change the solid 1mm of metal, to a small taper that tries to stop the magnets a bit closer to the tool surface. The danger is if someone needs reams out the hole they might tear though the tapered section and then the magnets can fall out. (Glue is the solution here). I got to think about if it is worth it.

                                  1 Reply Last reply
                                  • comis Offline
                                    comis
                                    Posts: 11,394
                                    comis Offline
                                    comis
                                    wrote on last edited by
                                    #88 Quote Reply

                                      What wonderful design and executed very well too! Looking forward to the final product! :tu:

                                      1 Reply Last reply
                                      • ZapWizard Offline
                                        ZapWizard
                                        Posts: 171
                                        ZapWizard Offline
                                        ZapWizard
                                        wrote on last edited by
                                        #89 Quote Reply

                                          I ran a few tests to ensure this is up to the task:

                                          The bottle opener works.


                                          The 4mm bit driver handles plenty of torque. The tool body started to bend when I reached 14 in-lbs (1.6 Nm)


                                          The 1/4" wrench handled more than 30 in-lbs (3.4 Nm).

                                          1 Reply Last reply
                                          • Dutch_Tooler Offline
                                            Dutch_Tooler
                                            Posts: 4,434
                                            Dutch_Tooler Offline
                                            Dutch_Tooler
                                            wrote on last edited by
                                            #90 Quote Reply

                                              This is awesone work Zap :like: :like:

                                              Could I perhaps ask you to consider adding the LM 2D bit slot all the same? Or maybe an alternate model that has this instead of the transversal 4mm hex? I for one have the LM bits, and they make for a reasonably compact carry in the bit card. I'm sure I'm not the only potential buyer that could benefit.

                                              1 Reply Last reply
                                              • Poncho65 Offline
                                                Poncho65
                                                Global Moderators
                                                Posts: 88,523
                                                Poncho65 Offline
                                                Poncho65
                                                Global Moderators
                                                wrote on last edited by
                                                #91 Quote Reply

                                                  :iagree: about the bits :cheers: also that is some great results in the testing as well :salute: :like:

                                                  1 Reply Last reply
                                                  • Wspeed Offline
                                                    Wspeed
                                                    Posts: 76,225
                                                    Wspeed Offline
                                                    Wspeed
                                                    wrote on last edited by
                                                    #92 Quote Reply

                                                      Excellent testing looks like it can handle some torque :like: :like: :tu:

                                                      1 Reply Last reply
                                                      • ZapWizard Offline
                                                        ZapWizard
                                                        Posts: 171
                                                        ZapWizard Offline
                                                        ZapWizard
                                                        wrote on last edited by
                                                        #93 Quote Reply

                                                          @Dutch_Tooler said:
                                                          Could I perhaps ask you to consider adding the LM 2D bit slot all the same? Or maybe an alternate model that has this instead of the transversal 4mm hex?

                                                          It would need to be an alternate model. I tried a few things today in CAD, but it works out to be too thin in critical places if I try to mix both together. I also realized I don't need a mixed horizontal opening, as the 1/4" wrench works well on the flat bits.

                                                          I did update the magnet stop to be smaller, this is live on the shop now. I have another batch of things to order, so I will get a new build, this time in a different finish. (The 24K gold plating is pretty, but it flakes off too easy for a tool)

                                                          1 Reply Last reply
                                                          • Dutch_Tooler Offline
                                                            Dutch_Tooler
                                                            Posts: 4,434
                                                            Dutch_Tooler Offline
                                                            Dutch_Tooler
                                                            wrote on last edited by
                                                            #94 Quote Reply

                                                              @ZapWizard said:
                                                              It would need to be an alternate model. I tried a few things today in CAD, but it works out to be too thin in critical places if I try to mix both together. I also realized I don't need a mixed horizontal opening, as the 1/4" wrench works well on the flat bits.

                                                              I did update the magnet stop to be smaller, this is live on the shop now. I have another batch of things to order, so I will get a new build, this time in a different finish. (The 24K gold plating is pretty, but it flakes off too easy for a tool)

                                                              If that's the case, then so much the better. Looking forward to v1.0 :drool: :like:

                                                              1 Reply Last reply
                                                              • Happy Gilmore Offline
                                                                Happy Gilmore
                                                                Posts: 1,065
                                                                Happy Gilmore Offline
                                                                Happy Gilmore
                                                                wrote on last edited by
                                                                #95 Quote Reply

                                                                  Truly incredible work. For this item alone I am considering buying the P4. Personally I would replace the mediocre tools rather than the awesome flat driver and Philips. Other than that though I would LOVE the heck out of that thing. I use 4mm bits all the time.

                                                                  Cheers,
                                                                  H.G.

                                                                  1 Reply Last reply
                                                                  • ZapWizard Offline
                                                                    ZapWizard
                                                                    Posts: 171
                                                                    ZapWizard Offline
                                                                    ZapWizard
                                                                    wrote on last edited by
                                                                    #96 Quote Reply

                                                                      I should receive my bronze Rev 2 model in the mail in the next few days. I will post images for those interested in that finish. If I didn't already mention it, the gold plating flakes off in areas of contact.

                                                                      Just dropping this here for anyone interested: A person on Reddit asked if they could re-arrange the stack up to ditch the Philips, ruler and can opener. But keep the package opener. Yes it is possible, and doesn't require any extra parts. Just double stack on of the existing washers. You can alternatively keep the Philips instead.

                                                                      And here is a dimension ed image showing the stack up for anyone who wants to swap stuff around. As long as your left/right stacks add up to 0.52 inches you can do whatever you want.

                                                                      1 Reply Last reply
                                                                      • Happy Gilmore Offline
                                                                        Happy Gilmore
                                                                        Posts: 1,065
                                                                        Happy Gilmore Offline
                                                                        Happy Gilmore
                                                                        wrote on last edited by
                                                                        #97 Quote Reply

                                                                          @ZapWizard said:
                                                                          I should receive my bronze Rev 2 model in the mail in the next few days. I will post images for those interested in that finish. If I didn't already mention it, the gold plating flakes off in areas of contact.

                                                                          Just dropping this here for anyone interested: A person on Reddit asked if they could re-arrange the stack up to ditch the Philips, ruler and can opener. But keep the package opener. Yes it is possible, and doesn't require any extra parts. Just double stack on of the existing washers. You can alternatively keep the Philips instead.

                                                                          And here is a dimension ed image showing the stack up for anyone who wants to swap stuff around. As long as your left/right stacks add up to 0.52 inches you can do whatever you want.

                                                                          Man, I wish you were in Philly. So many ideas to explore with your skill set, amazing job. This looks awesome! I also think that tool arrangement makes a ton of sense. It would be a shame to lose an awl, file, or the prybar/box cutter.

                                                                          1 Reply Last reply
                                                                          • SirVicaLot Offline
                                                                            SirVicaLot
                                                                            Posts: 5,979
                                                                            SirVicaLot Offline
                                                                            SirVicaLot
                                                                            wrote on last edited by
                                                                            #98 Quote Reply

                                                                              Amazing job ZW! :like:

                                                                              Hey LM, see what you can do with the p series :pok: That’s what we want, darn it :twak:

                                                                              Now even I consider buying a P4...once the price drops :D

                                                                              1 Reply Last reply
                                                                              • ZapWizard Offline
                                                                                ZapWizard
                                                                                Posts: 171
                                                                                ZapWizard Offline
                                                                                ZapWizard
                                                                                wrote on last edited by
                                                                                #99 Quote Reply

                                                                                  The bronze steel part arrived. This is Rev 2 (And the version anyone who ordered is getting). This one requires less reaming out, and no hammering like you see in the video. The magnets also has a closer to the bit for a better hold on the bit.

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. Leatherman Tools
                                                                                  4. ZapWizard's Leatherman Free P4 Mods
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0