Notables No.1: The skinny on a fat tool; the Gerber Auto Recoil
-
If you put a cross hatch pattern on the top edge of the finger openers with a Dremmel or similar tool it makes one hand opening of the blades a lot easier. You can also loosen the blades slightly by opening the screw part of the axle, be careful though because if you go too loose the slide lock plate will drop down and not work!
I would say closing the plier was comparable to closing a extending baton and should only be closed against the floor, brick wall or a steel toe cap and definitely not against anything that would damage. The springs are very strong. I have a heavy metal belt buckle that I sometimes use.
The drivers are strong enough to be used and if you care to grind the top and bottom of the Phillips it can be used with the new bit adapter that Gerber make.
If the scissors are locking, is it because the spring is slipping off allowing the blades to jam. If so file a slight ramp to help trap the spring at the contact point.
I do not use mine at work but carry it at all other times. It is tough enough to do all the weekend jobs that may crop up. Small enough to go unnoticed in a jacket pocket, but it is still a gimmick.
Dave
-
Good to hear that you've had no problems with accidental discharge so far Spoon. (Be careful though, as this tends to occur more as your tool gets older!)

Seriously though, I tend to lump the Recoil into the same catagory as the SOG SwitchPlier, the Vic AutoTool, and the new Gerber Radius. All are fascinating little gadgets, great conversation pieces, but only marginally useful.
More fun to play with than to actually use.
-
@damota said:
If the scissors are locking, is it because the spring is slipping off allowing the blades to jam. If so file a slight ramp to help trap the spring at the contact point.
I do not use mine at work but carry it at all other times. It is tough enough to do all the weekend jobs that may crop up. Small enough to go unnoticed in a jacket pocket, but it is still a gimmick.
Dave
On my model the scissors jam because the handle slips between the anti-clump washer and the other half of the scissors. It's not too big of a deal, just something to be aware of.
This was sort of a practice thread, I'm trying to catalogue all the little things most of us miss when researching a tool before purchase since many of us cannot always handle one in person. The impetus for this was the overall thickness of the Recoil. I searched high and low for reviews and pictures but only found a few reviews and only found a picture of the thickness after I had ordered it (from equipped.org's SHOT coverage from years ago), somewhat suprising to me when I finally recieved it and saw how much bigger it was than expected.
I have some others planned when I have time and I wanted to see how this pans out. It could be a valuable resource for the site.
First lesson; don't photograph multi-tools on top of a catalogue featuring pictures of other tools. ::)
@J-sews said:
Good to hear that you've had no problems with accidental discharge so far Spoon. (Be careful though, as this tends to occur more as your tool gets older!)


-
@Spoonrobot said:
......or if it is merely a "gadget" for the uninitiated to purchase on impulse, play with for a few days and ultimately spend it's life in the junk drawer.....My Recoil falls squarely into this catagory. I haven't toyed around with it at all since the first few days after I bought it. Your review has got me looking at it again though:
Unlike yours, my knife blade can be flicked open one-handed even though the pliers are retracted.
The combo tool in the other handle should be one-hand accessable as well, except that it is wrong handed. Totally untrained, my left thumb seems to be too stupid to flick open knife blades.
Like yours, the "second" blades on mine are impossible to access alone. The front blade has to be opened first in order to get at the blade behind it.
The mainsprings seem much stouter than they need to be. After firing, it is downright clumsy and difficult to re-charge the plier head.
It is fat, fat, way too fat. -
Another fine review there mate.

gerber do seem to be producing some weird designs these days, and fair play to them for pushing the envelope.
-
Just dredging this old thread up again for sentimental reasons. Anybody else got one of these?
-
Still looking for one myself...
Def
-
-
Well I have one now myself, and it is pretty neat- in concept at least. Just to give you an idea of the force this puppy comes out at, the plier head can launch a beer cap over a foot in the air.
Def
-
I have joined this exclusive club
:D. My "new" had a lot of surface rust on it & was quite dirty
>:(. After a good clean , a fight with a rust eraser & a good lube.It has come up looking quite good. The staff room table at work has some Recoil prints on it from were I pushed the pliers on it to retract them >:D.
The one thing that I am a little concerned is the tool has a slightly faulty lock on the secondary tools. The plain screw driver tool that is next too the scissors, jams when opened a 1/3 of the way , it can be closed but not opened any further. I can get around the problem by holding the lock down when deploying the tool (awkward) , the scissors have no problems
.For some reason the sliding lock disengages from the lock slot on the black plastic lock when opening the tool. If I hold down the black plastic lock on opening the tool, the sliding lock stays in the plastic slot.
Does any one else have this problem ???The problem side's lock is definitely less smooth sliding than good side.The locks have been well cleaned & lubed. -
Mat, I never had that problem before. UNTIL NOW! I could not re-create what you were describing while the pliers were "closed". But when I open the pliers, the "sliding lock disengages from the lock slot on the black plastic lock" as you describe.

I think it is because Gerber uses the same coil spring to fire out the plier head as is used to engage the blade locks. There just isn't enough tension in the spring when the pliers are "out"
Do you have any problem with your blades when the pliers are "in"?
-
Thanks very much for checking Bob
.
Pliers in or out does not seem to make a difference to my one
.Being plastic I am a little concerned it may break , best not EDC the Recoil
:D.
Bob, Gerber does not still make the recoil do they? I wonder if they were contacted if they could give us a answer about the lock problem?
The tension on those springs is MAD more like a catapult than a plier deployer

-
They haven't shown it on their website for a while now. And it wasn't in their 2008 catalog. Guess I can't say for sure when it was discontinued.

Yah, that rocket launcher spring is pretty powerful! I've got little plier-tip dents all over the edge of my work bench!

-
-
@MultiMat said:
Fingers sore
:D. Today is the first day I have had a chance to clean & play with the mouse trap Gerber.
Bob how hard is it to adjust the tamper proof fasteners on the Recoil ? I wonder if a bit of fine tuning would make any difference ?Could be the solution Mat (but I've never tried it myself)

-
@MultiMat said:
Fingers sore
:D. Today is the first day I have had a chance to clean & play with the mouse trap Gerber.
Bob how hard is it to adjust the tamper proof fasteners on the Recoil ? I wonder if a bit of fine tuning would make any difference ?Grip the head with a pair of lock jaws (I use a Crunch to maintain my Gerbers) give it a firm twist just to see if it moves. If it does not, change to the other side and try moving that. One side (the axle part) is locked in the frame by small protrusions in the frame hole that fit into slots in the axle part. The part to loosen is a grub screw that is made to match the axle head with the grooves. Only turn the grub screw a slight amount to loosen or tighten it. If too slack that is when the lock plate drops out if the head is out! Just tighten it a little if that happens. If too tight it will bind the handle tools. If you use Locktight you should have it correct by the time it sets. You must test it as you adjust the screw and by small I mean small less than an 1/8 of a turn. I fitted a pocket clip under the grub screw on mine and it gets used more than any of my other tools now. Handy tool.
Dave
-
Fingers sore
:D. Today is the first day I have had a chance to clean & play with the mouse trap Gerber.
Bob how hard is it to adjust the tamper proof fasteners on the Recoil ? I wonder if a bit of fine tuning would make any difference ?Grip the head with a pair of lock jaws (I use a Crunch to maintain my Gerbers) give it a firm twist just to see if it moves. If it does not, change to the other side and try moving that. One side (the axle part) is locked in the frame by small protrusions in the frame hole that fit into slots in the axle part. The part to loosen is a grub screw that is made to match the axle head with the grooves. Only turn the grub screw a slight amount to loosen or tighten it. If too slack that is when the lock plate drops out if the head is out! Just tighten it a little if that happens. If too tight it will bind the handle tools. If you use Locktight you should have it correct by the time it sets. You must test it as you adjust the screw and by small I mean small less than an 1/8 of a turn. I fitted a pocket clip under the grub screw on mine and it gets used more than any of my other tools now. Handy tool.
Dave
Thanks very much Dave
I will give it a go tomorrow . -
-
I gave it a go & tightened the fastener with my Crunch incrementally , checking as I went & unfortunately no difference
. I got to the point of tightness were it was extremely difficult to open the tools out. Looking at the locks action , there is no problem opening the scissors BUT the screw driver tool next to it seems to lift/tilt the metal tab lock up & out of the slot in the black plastic lock switch. I wonder if it has something to do with the screw driver tool's end profile 
I am not TOO disappointed as I got the Recoil purely as a tool of interest
& not a user as such (sorry Ben :P). It is just the OCD in me causing trouble. ::) 
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login