Notables No.1: The skinny on a fat tool; the Gerber Auto Recoil
-
@Spoonrobot said:
......or if it is merely a "gadget" for the uninitiated to purchase on impulse, play with for a few days and ultimately spend it's life in the junk drawer.....My Recoil falls squarely into this catagory. I haven't toyed around with it at all since the first few days after I bought it. Your review has got me looking at it again though:
Unlike yours, my knife blade can be flicked open one-handed even though the pliers are retracted.
The combo tool in the other handle should be one-hand accessable as well, except that it is wrong handed. Totally untrained, my left thumb seems to be too stupid to flick open knife blades.
Like yours, the "second" blades on mine are impossible to access alone. The front blade has to be opened first in order to get at the blade behind it.
The mainsprings seem much stouter than they need to be. After firing, it is downright clumsy and difficult to re-charge the plier head.
It is fat, fat, way too fat. -
Another fine review there mate.

gerber do seem to be producing some weird designs these days, and fair play to them for pushing the envelope.
-
Just dredging this old thread up again for sentimental reasons. Anybody else got one of these?
-
Still looking for one myself...
Def
-
-
Well I have one now myself, and it is pretty neat- in concept at least. Just to give you an idea of the force this puppy comes out at, the plier head can launch a beer cap over a foot in the air.
Def
-
I have joined this exclusive club
:D. My "new" had a lot of surface rust on it & was quite dirty
>:(. After a good clean , a fight with a rust eraser & a good lube.It has come up looking quite good. The staff room table at work has some Recoil prints on it from were I pushed the pliers on it to retract them >:D.
The one thing that I am a little concerned is the tool has a slightly faulty lock on the secondary tools. The plain screw driver tool that is next too the scissors, jams when opened a 1/3 of the way , it can be closed but not opened any further. I can get around the problem by holding the lock down when deploying the tool (awkward) , the scissors have no problems
.For some reason the sliding lock disengages from the lock slot on the black plastic lock when opening the tool. If I hold down the black plastic lock on opening the tool, the sliding lock stays in the plastic slot.
Does any one else have this problem ???The problem side's lock is definitely less smooth sliding than good side.The locks have been well cleaned & lubed. -
Mat, I never had that problem before. UNTIL NOW! I could not re-create what you were describing while the pliers were "closed". But when I open the pliers, the "sliding lock disengages from the lock slot on the black plastic lock" as you describe.

I think it is because Gerber uses the same coil spring to fire out the plier head as is used to engage the blade locks. There just isn't enough tension in the spring when the pliers are "out"
Do you have any problem with your blades when the pliers are "in"?
-
Thanks very much for checking Bob
.
Pliers in or out does not seem to make a difference to my one
.Being plastic I am a little concerned it may break , best not EDC the Recoil
:D.
Bob, Gerber does not still make the recoil do they? I wonder if they were contacted if they could give us a answer about the lock problem?
The tension on those springs is MAD more like a catapult than a plier deployer

-
They haven't shown it on their website for a while now. And it wasn't in their 2008 catalog. Guess I can't say for sure when it was discontinued.

Yah, that rocket launcher spring is pretty powerful! I've got little plier-tip dents all over the edge of my work bench!

-
-
@MultiMat said:
Fingers sore
:D. Today is the first day I have had a chance to clean & play with the mouse trap Gerber.
Bob how hard is it to adjust the tamper proof fasteners on the Recoil ? I wonder if a bit of fine tuning would make any difference ?Could be the solution Mat (but I've never tried it myself)

-
@MultiMat said:
Fingers sore
:D. Today is the first day I have had a chance to clean & play with the mouse trap Gerber.
Bob how hard is it to adjust the tamper proof fasteners on the Recoil ? I wonder if a bit of fine tuning would make any difference ?Grip the head with a pair of lock jaws (I use a Crunch to maintain my Gerbers) give it a firm twist just to see if it moves. If it does not, change to the other side and try moving that. One side (the axle part) is locked in the frame by small protrusions in the frame hole that fit into slots in the axle part. The part to loosen is a grub screw that is made to match the axle head with the grooves. Only turn the grub screw a slight amount to loosen or tighten it. If too slack that is when the lock plate drops out if the head is out! Just tighten it a little if that happens. If too tight it will bind the handle tools. If you use Locktight you should have it correct by the time it sets. You must test it as you adjust the screw and by small I mean small less than an 1/8 of a turn. I fitted a pocket clip under the grub screw on mine and it gets used more than any of my other tools now. Handy tool.
Dave
-
Fingers sore
:D. Today is the first day I have had a chance to clean & play with the mouse trap Gerber.
Bob how hard is it to adjust the tamper proof fasteners on the Recoil ? I wonder if a bit of fine tuning would make any difference ?Grip the head with a pair of lock jaws (I use a Crunch to maintain my Gerbers) give it a firm twist just to see if it moves. If it does not, change to the other side and try moving that. One side (the axle part) is locked in the frame by small protrusions in the frame hole that fit into slots in the axle part. The part to loosen is a grub screw that is made to match the axle head with the grooves. Only turn the grub screw a slight amount to loosen or tighten it. If too slack that is when the lock plate drops out if the head is out! Just tighten it a little if that happens. If too tight it will bind the handle tools. If you use Locktight you should have it correct by the time it sets. You must test it as you adjust the screw and by small I mean small less than an 1/8 of a turn. I fitted a pocket clip under the grub screw on mine and it gets used more than any of my other tools now. Handy tool.
Dave
Thanks very much Dave
I will give it a go tomorrow . -
-
I gave it a go & tightened the fastener with my Crunch incrementally , checking as I went & unfortunately no difference
. I got to the point of tightness were it was extremely difficult to open the tools out. Looking at the locks action , there is no problem opening the scissors BUT the screw driver tool next to it seems to lift/tilt the metal tab lock up & out of the slot in the black plastic lock switch. I wonder if it has something to do with the screw driver tool's end profile 
I am not TOO disappointed as I got the Recoil purely as a tool of interest
& not a user as such (sorry Ben :P). It is just the OCD in me causing trouble. ::) 
-
-
@DaveK said:
That would drive me nuts Mat. It doesn't matter if I'm going to use a tool, it has to function as though I am. >:DStop dilly dallying and take it apart. You know it makes sense

I do not know if I like the Recoil THAT much
:D. Visions of small pieces of Gerber being launched into orbit by those springy springs
:ahhh.
I think I would tackle my Bear Jaws iffy locks before delving into Jack in the box ,spring launching, tiny pieces, Gerber oddities.
Soft I know ::)

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login