ZapWizard's Leatherman Free P4 Mods
-
@ZapWizard said:
I have had at least a dozen requests for a Leatherman flat bit version. I think I can go ahead and make it now that I know the shrinkage amount and got the locking portion to work correctly. But alas I will be offline for most of this month, so it will have to wait until later.

-
Zap! Totally fantastic! Put me in for the LM flat version too!
-
Hmm, I think the flat version is going to need a stronger magnet and a barrier between the magnet and bits. Otherwise magnet is likely to crack. Zap probably already knows this I'm betting
-
I do like the magnet idea for the bit-driver. Leatherman uses only 2 types of bit holders a hinged version for the Skeletool and the regular one used on the other multitools. Neither one of those use a magnet.
-
Zap, do you think there is a way to make a t shank exchanger in the scissor slot? That would sell me on the P2 with both your add-ons right now.
-
I’d be in for the Leatherman version.
Sent from my iPhone using Tapatalk
-
Awesome work Zap!

Already ordered a holster for my Charge TTi (open clip version). Can not wait anymore

Thank you for your outstanding engineering performance
.Greetings from Austria
-
@Happy Gilmore said:
Zap, do you think there is a way to make a t shank exchanger in the scissor slot? That would sell me on the P2 with both your add-ons right now.I don't think I could do that with 3D printing, it would require both milling and sheet metal parts.
@Sidewinder said:
Already ordered a holster for my Charge TTi (open clip version). Can not wait anymore
Thank you for your outstanding engineering performance
.Thanks.
I am going to be working on the Leatherman Flat bit soon. I am getting lots of requests for it from YouTube and email.
-
@ZapWizard said:
I don't think I could do that with 3D printing, it would require both milling and sheet metal parts.
Thanks.I am going to be working on the Leatherman Flat bit soon. I am getting lots of requests for it from YouTube and email.
thats great news!

-

Howdy folks. I have been working on other projects, as well as getting my eyes lasered. I recently got back to working on my tool designs.
Due to popular demand: I ordered a Leatherman FREE P2. I have to say, I don't think the P2 is a good option compared to the P4, only because it isn't that much thinner or lighter. Holding them side by side, you will see the P2 actually had the front scales tilted towards the middle, making it thicker than it appears. It is only a few millimeters thinner than the P4. Both are expensive, so I understand perhaps saving a few bucks to get the P2.
However, folks will still get the P2 and need a holster for it. My design is now complete, and just need to order the prototype in the next week or so. It is very similar to the FREE P4 holster. The only real difference is that you can't put it in four different ways, just two. The tilted front scales prevent flipping it around.


I also finally came up with design I like for the Leatherman Flat Bit Holder. The design ditched the magnets, as they just don't work well with the Leatherman double sided bits. Instead I have two arms that will grip the small detents on the side of the bits.
To ensure it can handle lots of torque, the sides wrap around the front to keep this as stiff as possible. Another awesome thing you can do with 3D printing that is impossible using other production methods. It does mean that it will have issues with recessed screws, but that is what the Leatherman Bit Extender is for.


As with the prototype, it folds into the tool with the bit at an angle, but deploys straight.
It will also have a 1/4" horizontal opening, but no bottle opener.I would love your folks feedback while I work on a few other designs. Also coming soon: FREE series holsters with 4mm and Flat bit holders on the back side. The SuperTool 300 holster design.
-

Just one smaller concern, it seems that there is not a lot that holds the back end of the inserted bit in place against torque and bending apart from the inner side walls (only restrictive sideways, not up/down), so all that holds the bit in particular against torque and up/down bending is the front, curved part of the bit holder. I realise this is probably due in part to the design of the springs, but perhaps one could still add some faces inside that hold the LM-profiled (if that makes sense) part of the back end of the bits? For this, you might need to decrease the spacing between the spring arms and the adjacent fixed faces, but it would be worth it. Or alternatively execute each spring as a bifurcated loop surrounding a central, comparatively rigid hollow holding profile, where the apex of the loop engages the bit's indent (hope this is clear
).Edited for clarification (hopefully)
-
I think your talking about torque twisting the bit along the same axis as the bit-grips. (Clockwise/Counter-clockwise relative to the cut-away image)
Right now any torque in that direction would push up against the inside surface of the spring, since it would hit the middle of the spring, there would be lots more force here, and the springs wouldn't move much.The spring arms need to be as long as possible simply due to the fact that the material is quite stiff, as well as to discourage cracking over time. Springs like this are always a bit tricky, I have to prototype the part in the actual material, and then test the feel to ensure they aren't too tight or too loose. With the goal of holding the bit, but allowing it to be removed by just your fingers.
After looking at the cutaway, with non-1am eyes, I realized that since I removed the magnets I have more space behind the bit. I can actually move the entire bit backwards a bit, this would allow the front flat-hex opening to become deeper.
-
That would certainly help
but my engineer's mind would rest a little easier if there were some additional support for the bit at the back end opposite the curved front part as seen from the spring arm tooth (yes, correct, in torque as seen (counter-)clockwise in Pic 3 in your post earlier today). Otherwise the front end would take all the load which might overstress the collar, even if you made it thicker. -
This is truely amazing, and you managed to get a 1/4 inch hex in there as well...your a magician. You might be able to improve it slightly but this is already dramatically stronger than the versions found in the wave/charge/surge etc.
Hmm I wonder if this works on a T2...
-
Zapwizard, you have convinced me that the Free P4 can be redeemed, i cant wait to see the flat driver and how it turns out, I plan on getting the P4 eventually and I will be buying one of your adapters first for sure!
-
I made the front portion deeper, and ordered the prototype. It will be here in a few weeks.
-
:ahhh

Looking forward to this (despite my misgivings, which I'll admit may be entirely unfounded
). -
Great stuff Zap!
Looking forward to seeing what you do with the ST300 sheath. I have one in need of an upgrade.
Will you be making it with the LM flat bit holders on the back as well? Mine is modded with a bit driver and I'd love to be able to carry the bits integrated into the sheath.
-
@Toolslinger said:
Will you be making it with the LM flat bit holders on the back as well? Mine is modded with a bit driver and I'd love to be able to carry the bits integrated into the sheath.I will be making the FREE P2 and P4 holsters with bit holder, but not for the SuperTool 300 as it just isn't popularly modded. However, once I release it, you can message me and I can do a custom one-off version.
-
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
Hey folks, I made a video just for you.
The Flat Bit Driver will work, it just needs some prototyping to get it to turn out accurate from the factory. I had to use a diamond bit on a dremel, and lots of filing to bring the dimensions in line. For some reason this part shrunk more than the hex cutout I put into the 4mm Bit driver.
I also have the prototype for the Leatherman FREE P2, and tested the open clip for myself.
Finally, not in the video: I have completed my designs for the SuperTool 300, and FREE P2 and P4 holsters with bit holders on the back. Adding those bits created 24 new unique configurations!
I will be ordering prototypes of those, along with a tweaked bit driver soon.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login