Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Easy Swiss Champ blade swap

Scheduled Pinned Locked Moved The Mod Squad
20 Posts 1 Posters 1.2k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Easy Swiss Champ blade swap
Easy Swiss Champ blade swap
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Max Stone Offline
    Max Stone
    Posts: 5,982
    Max Stone Offline
    Max Stone
    wrote on last edited by
    Quote Reply

      SC I got as a trade yesterday had a small blade that had been resharpened a few times and was a little out of shape. Swiss Champs are quite a mission to disassemble, so I decided to just push through a new pin on the end with the blade. So rather than a 5 hour job, this only took an hour and a half.

      First was to remove the scales. I soak the SAK in hot water for 5 minutes to soften the plastic. This reduces damage to the mounts so you can reuse them.

      I don’t like the can opener trick as this can damage the edge. I push a thin flat driver into the toothpick/tweezer slot to lever up and pop off the scales.

      These are the solid Plus scales, and they are so much nicer than the new cavity-type scales. Interesting to see a date stamp of 86, which is right at the start of the Swiss Champ’s release.

      Next to drill out the pivot collar. This needs to be the one on the side closest to the small blade, as this is where the new pin will be driven through.

      I use a Dremel and 2.5mm drill to remove enough of the brass to remove the collar. With care, it’s possible to save the collar for reuse.

      Then I cut about 4cm of 2.5mm rod. I soften the edge and polish the ends as it helps make a better rivet head.

      233A2E38-12EF-463D-9C24-4D2C3E9CF68A.jpeg

      ABFA942A-39FE-4A73-918E-E20C8E1ECB73.jpeg

      D296DB82-FAD8-4D14-82AD-B20F82BD16FE.jpeg

      2C1D7D3A-400B-48C2-89FC-A62CC79E49C2.jpeg

      1 Reply Last reply
      • Max Stone Offline
        Max Stone
        Posts: 5,982
        Max Stone Offline
        Max Stone
        wrote on last edited by
        #1 Quote Reply

          I sandwich the pin between hardboard, placed halfway down between them so that when pressed tight in the vice, the base is trapped and won’t move down as you hammer.

          I use a 350g ball hammer. I start with the flat side to get some swell on the top, and then switch to the ball to spread and shape the head. I alternate the flat and ball ends until I get a good shape. A tip is to polish the hammer surfaces as this makes for a neater finish on the rivet.

          It’s important to get enough of a head so that it seats proud of the collar. Otherwise it won’t remain tight in the collar when you close the opposite end.

          F289B13A-83C7-45D5-B07E-7B4C44ACE6F3.jpeg

          C581A3A6-B5BA-41BB-9AAF-BE639E07BFB6.jpeg

          BABEAF30-4E17-443F-8896-BDDFF7CF1BE8.jpeg

          0E0F9C56-5511-4B8E-9435-0D9B79E94047.jpeg

          1 Reply Last reply
          • Max Stone Offline
            Max Stone
            Posts: 5,982
            Max Stone Offline
            Max Stone
            wrote on last edited by
            #2 Quote Reply

              As a finishing touch, I polish the rivet head. The pic shows the correct seating of the rivet head in the collar.

              I then round and polish the opposite end of the pin to center and follow the pin to be pushed out. I’m now ready to extract the small blade.

              I space my vice jaws just enough to give clearance for the rivet at the bottom. Only the scales rest on the jaws, which I cover with tape to protect the scales.

              2E081780-A7D0-4E2B-81EF-CCC26B53E82B.jpeg

              861B28BD-72C6-472D-97AD-A275070B812A.jpeg

              659C68BE-83E6-48E9-8B7C-494D79B0706D.jpeg

              3083602B-2461-42E8-BDD1-AB1B8E490DA4.jpeg

              1 Reply Last reply
              • Max Stone Offline
                Max Stone
                Posts: 5,982
                Max Stone Offline
                Max Stone
                wrote on last edited by
                #3 Quote Reply

                  Next I drift out the original pin using the new pin, just enough to release the small blade.

                  As the small blade has a spacer, the backspring stays in place against it. So long as you only tap the pin down just enough to release the blade.

                  Here’s the old and new blade. Yes, the profile is not too bad, but was enough to give me an excuse to swap it.

                  84740093-9AD4-4404-8EF1-33AB4D193841.jpeg

                  33E895CC-D167-411A-A33E-665C61EFD8C2.jpeg

                  69CB58D3-5B3C-4FA7-B1EF-79382047600C.jpeg

                  7C7686EA-601B-4663-A7CF-72013F047949.jpeg

                  1 Reply Last reply
                  • Max Stone Offline
                    Max Stone
                    Posts: 5,982
                    Max Stone Offline
                    Max Stone
                    wrote on last edited by
                    #4 Quote Reply

                      The new blade fitted in easily. Needed a little pressure to center over the top of the exposed pin. I put some tape on the blade for some protection.

                      Now ready to drive through the new pin. Don’t forget to slide on the collar, as once you’ve driven the new pin down, that’s it’s final position.

                      Here you can see progress at the halfway point, new pin at the top, old coming out the bottom. I tap through with the SAK on the vice with the jaws slightly open. When the original pin drops out, keep it for a future build, but you’ll need to reuse the collar. Finish tapping the new pin all the way down.

                      7B07444F-FFEB-48EA-BB52-41A3287063FC.jpeg

                      D98A3E86-7732-4D06-83C7-3294D0A08720.jpeg

                      D3482283-B05B-46EC-8843-53DE57490C4F.jpeg

                      B60C3E03-CC3B-4B25-BCF9-AFEC5E62B794.jpeg

                      1 Reply Last reply
                      • Max Stone Offline
                        Max Stone
                        Posts: 5,982
                        Max Stone Offline
                        Max Stone
                        wrote on last edited by
                        #5 Quote Reply

                          Here’s the old pin and the new pin in place, ready for trimming. This is a good time to test the new blade and maybe have a cup of tea.

                          To peen closed, I cut off just less than the thickness of the collar. I use a diamond cut-off disk on my Dremel to cut and grind a nice flat end on the pin.

                          3215C600-6E81-4886-BE50-71AFDD490096.jpeg

                          8FAD4F25-BEDD-4F7B-A101-45641B5813FB.jpeg

                          C0E39FDB-371C-42CE-81E6-C090AFBBF740.jpeg

                          38CAD2F6-8610-42B4-8D47-15423E423F0B.jpeg

                          1 Reply Last reply
                          • Max Stone Offline
                            Max Stone
                            Posts: 5,982
                            Max Stone Offline
                            Max Stone
                            wrote on last edited by
                            #6 Quote Reply

                              After cutting, I polish the end which also takes off the sharp edge.

                              I then put the collar back over the pin and use the anvil end of my vice to peen the pin into a rivet head shape. It’s important to peen enough to get a proper seat inside the collar, but also to close the layers tightly enough to not have wobble on the tools. To check, it helps to turn the SAK over and tap the opposite end of the pin when on the vice with the jaws open. Then turn back and continue to peen the top rivet on the anvil. It’s possible to have the fit too tight, and then the tools bind and won’t snap. But it’s generally a case of too much tool wiggle. So take time to check the peening is the correct tightness by testing the tools for wiggle.

                              D8339E3C-5046-47E1-8C20-2BD734062347.jpeg

                              280CAF5E-AB0B-4AF2-9821-119BD1AD2BD8.jpeg

                              836F9E0D-87FB-4188-9FAC-341BF327CBD9.jpeg

                              D52F48E0-DC03-4196-A97F-8D9A4E86708D.jpeg

                              1 Reply Last reply
                              • Max Stone Offline
                                Max Stone
                                Posts: 5,982
                                Max Stone Offline
                                Max Stone
                                wrote on last edited by
                                #7 Quote Reply

                                  I polished up the rivet when done, and then gave the SAK a good wash, opening and closing all the tools to get it clean.

                                  After a good rinse and dry, I snapped the scales back on. Oiled and all done!

                                  9E75B200-B255-4935-9DE1-1E5CE526D038.jpeg

                                  4CE147BD-47F9-4230-9827-6F2D29221B6D.jpeg

                                  0AEC7A2F-E2F1-408B-A03B-7DA2F1535C0E.jpeg

                                  EE78F1B3-5848-45AC-9764-C55129DBF5E3.jpeg

                                  1 Reply Last reply
                                  • magentus Offline
                                    magentus
                                    Admin Team
                                    Posts: 21,659
                                    magentus Offline
                                    magentus
                                    Admin Team
                                    wrote on last edited by
                                    #8 Quote Reply

                                      Beautifully done 'how to' there Max :cheers:
                                      Lovely pics.

                                      1 Reply Last reply
                                      • Max Stone Offline
                                        Max Stone
                                        Posts: 5,982
                                        Max Stone Offline
                                        Max Stone
                                        wrote on last edited by
                                        #9 Quote Reply

                                          Thanks magentus :hatsoff:

                                          1 Reply Last reply
                                          • PitCarver Offline
                                            PitCarver
                                            Posts: 3,025
                                            PitCarver Offline
                                            PitCarver
                                            wrote on last edited by
                                            #10 Quote Reply

                                              Awesome job, Max.
                                              Very good job.
                                              I picked up a handyman special of 58mm's, that included a MiniChamp and 2 additional classics. Looked like someone had taken a grinder to the scissors and main blade on the MiniChamp, so I did basically the same as you.
                                              Salvaged the scissors from 1 classic and the blade from the other. Drove the old pin out with the new, replacing the tools as I went along.
                                              Funny, how every source said that I had to totally disassemble the knife in order to replace the tools...
                                              This was my first, and only, so far, attempt at repair of a Victorinox.

                                              I was pleased with the outcome.

                                              1 Reply Last reply
                                              • McStitchy Offline
                                                McStitchy
                                                Global Moderators
                                                Posts: 19,785
                                                McStitchy Offline
                                                McStitchy
                                                Global Moderators
                                                wrote on last edited by
                                                #11 Quote Reply

                                                  Great job Max... well done :tu:
                                                  I didn't try the push-through method yet.
                                                  Will keep it in mind for sure after seeing this :D

                                                  1 Reply Last reply
                                                  • Max Stone Offline
                                                    Max Stone
                                                    Posts: 5,982
                                                    Max Stone Offline
                                                    Max Stone
                                                    wrote on last edited by
                                                    #12 Quote Reply

                                                      Thanks PitCarverb and Matt. :hatsoff:

                                                      If you measure the pin lengths it should be possible to replace any tool down the stack. I used the same method last year to replace the CS of a Ranger with a Phillips to make a Master Craftsman. So this is a viable method for both the center and outer pivots. :salute:

                                                      1 Reply Last reply
                                                      • NetsNJ Offline
                                                        NetsNJ
                                                        Posts: 676
                                                        NetsNJ Offline
                                                        NetsNJ
                                                        wrote on last edited by
                                                        #13 Quote Reply

                                                          Amazingly instructional.

                                                          1 Reply Last reply
                                                          • Max Stone Offline
                                                            Max Stone
                                                            Posts: 5,982
                                                            Max Stone Offline
                                                            Max Stone
                                                            wrote on last edited by
                                                            #14 Quote Reply

                                                              Thanks NetsNJ :hatsoff:

                                                              1 Reply Last reply
                                                              • SirVicaLot Offline
                                                                SirVicaLot
                                                                Posts: 5,979
                                                                SirVicaLot Offline
                                                                SirVicaLot
                                                                wrote on last edited by
                                                                #15 Quote Reply

                                                                  Great work, Max! Great write-up as well! :like:

                                                                  1 Reply Last reply
                                                                  • Myron Offline
                                                                    Myron
                                                                    Posts: 2,432
                                                                    Myron Offline
                                                                    Myron
                                                                    wrote on last edited by
                                                                    #16 Quote Reply

                                                                      Another awesome how-to! Thanks for taking the time to post this, Max. I really enjoyed reading it.

                                                                      Myron

                                                                      1 Reply Last reply
                                                                      • Max Stone Offline
                                                                        Max Stone
                                                                        Posts: 5,982
                                                                        Max Stone Offline
                                                                        Max Stone
                                                                        wrote on last edited by
                                                                        #17 Quote Reply

                                                                          Thanks Sir Vic, Myron. :hatsoff:

                                                                          1 Reply Last reply
                                                                          • Wspeed Offline
                                                                            Wspeed
                                                                            Posts: 76,225
                                                                            Wspeed Offline
                                                                            Wspeed
                                                                            wrote on last edited by
                                                                            #18 Quote Reply

                                                                              Excellent work Max and great write up and pics :like: :tu:

                                                                              1 Reply Last reply
                                                                              • Max Stone Offline
                                                                                Max Stone
                                                                                Posts: 5,982
                                                                                Max Stone Offline
                                                                                Max Stone
                                                                                wrote on last edited by
                                                                                #19 Quote Reply

                                                                                  Thank you Wim. :cheers:

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. The Mod Squad
                                                                                  4. Easy Swiss Champ blade swap
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0