3D Printer Blog
-
So much for my expectations. 9 hours print...1 hour to reveal the model from all the supports. I first looked at it and thought to myself...this is going to be fun. That soon went out the window when I realized I simply couldn't separate the model from its cocoon. Out came the tweezers, and then the X-acto knife. i quickly realized I would soon be a casualty so I put away the X-acto knife. Then came the mini pliers...and an hours hard labour. I am surprised at how well the model turned out...and that I somehow managed to not damage it at all.
There is a lesson learned here...I will have to figure out support and how to diminish it in a way where it won't affect the print and make it easier to remove.
. <a href="https://flic.kr/p/2j2PjJN" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49903664162_c8a895aefc_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8453A by Chako, on Flickr
-
Noticed something weird...when using CURA yesterday, I wanted to print upgrade parts for my printer, but ended up putting 2 files on the card...and got the model above named under the upgrade parts. I didn't mind and just rolled with it. I think I either made a mistake and named both files the same, or it is just best to deal with 1 file at a time. This morning, I am starting my upgrade parts. I noticed my travel speed was 50 and upped it to 60mm/s. That shaved a whole hour from production time. I think I may even be able to up the speed even more, but am curious to see the difference in print quality. based on my horror story above, I also changed support from grid to line. Curious to see if that will help any.
I forgot to say Vidar, I have a built in enclosure on its way from Amazon. Should be in any week now.
Anyhow, I found this curated batch of upgrades all in one print. In here are a set of tub retention clips, various other clips for wire management including the front LCD panel wire, and a retention clip to keep the extruder cabling away from the rear of the machine. Also found in here is the filament arm to reduce the acute entry angle into the filament feeder, a front fan cover to prevent filament from going into the main control box fan opening, and a set of shims to improve the alignment of the Z axis stepper motor. Not bad for an all in one print. Once this is done, I am thinking of printing a power supply fan quieter, and possibly a back for the LCD panel which is not protected at all. I looked at the long extensive list of upgrades available on Thingiverse, and found I can either print an LCD backing, or a complete separate box for the LCD housing. If I am going to put the printer in a built enclosure, I am thinking it might be advantageous to have the controls outside said enclosure. I also want to print a feeder knob, and a small device to keep the filament away from the Z axis screw. So many options...so many possibilities. :ahhh
<a href="https://flic.kr/p/2j2UEZT" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49904707877_1cb371f3aa_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8455A by Chako, on Flickr
<a href="https://flic.kr/p/2j2TfZ4" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49904431981_06d0a238d6_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8456A by Chako, on Flickr
-
44% done and all looks good so far. I think cleaning the heated bed with rubbing alcohol really helps the adhesion.
<a href="https://flic.kr/p/2j2SK6D" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49904331443_e3f45a6011_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8458A by Chako, on Flickr
-
Easy support removal, also in hard to reach places or inside parts, was the main reason I went for the Sigma printer back in the day. (Edit: The supports print in a different soluble material).
With supports in the same material it is manual fiddling for me too. Some materials print with brittle connections so they can be broken off fairly easily - others needs knife or pliers. There are some flat cutting electronic pliers that are quite nice for that.
There might be other options I don't know about too?
-
We've always had pretty good bed adhesion, but if we're printing small parts without a raft or brim, we'll spray some hair spray on the glass bed.
A lot of people seem to swear by using tree supports, but I've had mixed results with them. I try and only use supports when absolutely necessary.
-
There is a lot to learn...and I am learning on the go. I have only check marked the support option in CURA. For example, this most current one is using supports for inside the fan shroud. I won't know for sure, but I might have some difficulty in removing them inside that small piece.As it prints, I am thinking...here we go again.

-
Yes. The fan guard is unsalvageable. There is no way to remove those supports. I am going to try without any supports at a later time. :'(
-
Whoa, been off the forum for a week and I see you're making giant strides! The print quality seems very good too

I see you're getting an enclosure. Can I take it you're going to try printing ABS too? -
No. I don't want any toxic fumes in my living room. I thought the enclosure might help with temperature settings and to keep the dust off of the printer.
Ok. I just had an ah ha moment with CURA. I did not know that if I clicked on the advanced tab, I have a whole lot of options. I played around with the infill settings and figured out that I don't have to stick with 60% infill. For some unknown reason, when I slice a model, I still cannot preview it. If I can see what the support looked like, I could have said hell no to this mornings fan guard disaster, or the figurine I printed yesterday.
Me thinks I should try to find an instruction manual for CURA 4.6, or at least look at some instructional videos.
Update on the fan guard...although it is a thing of beauty I cannot remove all that inside plastic. So I found a different model and am printing that with no support to see what that might turn out like.
-
I think I will eventually print something out to store the tools. So far this is my starter kit.
<a href="https://flic.kr/p/2j34Y9q" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49906521568_ea8bf00b3d_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8463A by Chako, on Flickr
Here is the finished product I printed earlier. I struggled to clean the inside of that fan guard to no avail. It is unsalvageable as mentioned above. Too bad as it came out great. I am learning by trial and error the does and don'ts of support. CURA is one tricky program.
<a href="https://flic.kr/p/2j34Y8P" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49906521533_ddda32f527_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8466A by Chako, on Flickr
On the plus side, everything else came out good. I stored the little c clips away (always good to have more of those for the boden tube). I did manage to use the filament guide and the LCD cable clips to good use.
Here you can see the filament guide. In case you are wondering, my LED light is a Phillips Light Flute held there by its magnetic base.
<a href="https://flic.kr/p/2j39abX" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49907339167_201fd79422_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8467A by Chako, on Flickr
And the LCD cable clips in use.
<a href="https://flic.kr/p/2j34Y69" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49906521378_167d25c086_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8469A by Chako, on Flickr
-
Now I know the difference between a raft, a brim, and a skirt. :think:
Raft vs Brim vs Skirt: The Differences (incl. Cura settings)
3D printing raft vs. brim vs. skirt: Learn the differences between these adhesion assistants and which to choose, using Cura as an example.
All3DP (all3dp.com)
-
Ok...well that turned out very well without supports. Now my main board cooling fan is protected from any plastics raining down on it.
<a href="https://flic.kr/p/2j36frt" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49906771493_f8e94fb9bd_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8474A by Chako, on Flickr
And I also printed this file at the same time. This little plastic bit that slides onto the metal plate will ensure that my filament will not be rubbing against the Z axis screw which is full of lubricant. I gather lubricant and filament are not a good mix.
<a href="https://flic.kr/p/2j38TVW" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49907287836_0e7839f489_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8475A by Chako, on Flickr
The upgrade of my machine is well under way with all these little enhancements.
-
Nice! I think 3D printers are a first step to self-replicating Von Neumann machines (just need to add enough brains to form initiative haha).

-
@Dutch_Tooler said:
Nice! I think 3D printers are a first step to self-replicating Von Neumann machines (just need to add enough brains to form initiative haha).

Unfortunately, they currently are relying on the PEBKAC.
-
Any system is only as good as its weakest link.

Ok, this fine morning, I am printing a Yoda extruder knob. For the first time, I am looking at adding a raft and a different type of support...one that only builds a tower to support overhangs as opposed to supporting everything everywhere,
Trial and error continues, possibly with a lot of PEBKAC in the process. :ahhh
EDIT: I can tell from my initial raft layers that my right side of the bed is slightly out of level. I should probably halt everything, level the bed, and restart, but because I am experimenting with a raft, I am curious to see how this will turn out. So the experiment continues.
-
Ok..so this was the result.
<a href="https://flic.kr/p/2j3esKW" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49908373828_f8364938c5_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8477A by Chako, on Flickr
I think this part may need some painting down the road.
<a href="https://flic.kr/p/2j3iDhJ" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49909189702_4757d29c9d_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8478A by Chako, on Flickr
-
red is horrible for photography.
Concert pics with red lights

seems you defeated the pebkac this time in spite of the levelling issue?
-
I might paint it down the road.
-
It seem like you are off to a good start.
There are reference models available that tests various characteristics of your printer and material so it will be easier to find good settings, limits and orientation for parts and supports. (Typically some parts with various degrees of overhang, bridges, details and so on).
-
Do you mean the little tugboat called the Benchy? I haven't tried one of those yet.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login