Off brand challenge level 1
-
Day 3:
Just a quick pic, been a busy day.
The wire cutters work very well, clean cut of the thickest and thinnest stranded copper wire I could find

Sent fra min FRD-L09 via Tapatalk
-
And the pliers don’t get stuck doing so :D
-
Now this is good to know, and since they're an integral part of the jaw should be plenty strong; no more exploding replaceable carbide cutters!!!


-
Not sure how much abuse they will take but for electrical wires they should be perfectly fine

Sent fra min FRD-L09 via Tapatalk
-
Day 4:
The flathead works well as a screwdriver and prybar


Sent fra min FRD-L09 via Tapatalk
-
That's good news, some of those drivers twist round into little corkscrews then snap off

-
These are more good news, and looks like it is pretty squared and even; most C&C's I've seen tend to be somewhat rounded at the corners and at the tip, making them useless as screwdrivers.
I'll be waiting/watching for the phillips driver test, and if any of the square driver adapters work on it; I have Leatherman's RBD, Gerber's Tool Kit, and a couple of generic ones, and hope that at least one works with the Fatmax!

-
Day 5:
Used the pliers to adjust a fuse holder to fit the cables. The pliers did a good job


Sent fra min FRD-L09 via Tapatalk
-
Good to know!

BTW, Is the handle splay uncomfortable? From the action picture, it reminds me of the factory Rev/Wingman/Sidekick splay...
-
@Juan el Boricua said:
Good to know!
BTW, Is the handle splay uncomfortable? From the action picture, it reminds me of the factory Rev/Wingman/Sidekick splay...
I've never really figured out what all of you mean by handle splay
Is it how far the handles open in use?Sent fra min FRD-L09 via Tapatalk
-
Double post
-
@RF52 said:
I've never really figured out what all of you mean by handle splay
Is it how far the handles open in use?Sent fra min FRD-L09 via Tapatalk
Yes, that's it! I call splay how far, or close, the handles are from one another; a 1st gen. Gerber Multiplier has very little splay, and can pinch you if pliers slip and handles close ( but you'll be able to hold both handles while tackling a large bolt head, one handed). On the contrary, a Leatherman Skeletool has much more splay allowing for safe operation of the pliers, but can be difficult to turn or grab a large bolt head, probably requiring both hands. All this assuming that the person using the tools has small to medium hands, like myself. Large splay benefits people with larger hands, allowing a more comfortable grip to "squeeze".
-
Day 6:
These will atleast start off the day as my phone camera has started to act like a smurf. Might be able to get some action pics later.
Showing the handle splay opened and closed, a bit on the larger side for my hands (small to medium)


-
Tested the knife on some seatbelt fabric at work, had to change it anyway so why not have some fun

It took some effort, and I would rather have a sharp plain edge blade then combo edge or serrated. My plain edge Benchmade 943, Sog Kilowatt and Gerber Center-Drive sliced through the seatbelt without problems [emoji12]Sent fra min FRD-L09 via Tapatalk
-
I don't think i have ever cut a belt but i would have thought serrations might have helped there, pity
-
One of the perks of beeing a bus mechanic, people always ruin seatbelts and I get to test my knives when changing them

Sent fra min FRD-L09 via Tapatalk
-
Day 7:
Used the phillips driver to mount a licence plate, it works great for smaller screws but it is on the smaller side so probably best suited for home use.
I'll try to summarize my week with this tool.
The tool implements work as they should and feel solid, a bit to light pressure from the backsprings so they collapse easily.
If you keep them as centered as possible it's not a big problem.
The knife is obviously not any kind of supersteel but it will open your packages and other small jobs.
The pliers are actually quite good, better fit for large hands.
The scissors on mine has a broken spring so they do not work very well.
Did not try:
File, can and bottle opener.Oh, I don't think the phillips driver would work with any kind of bit adapter as it's quite thin.

Sent fra min FRD-L09 via Tapatalk
-
Thanks for your review, RF52; its solid and objective!
It appears that for an all-around-home/light duty can excell, and probably as stocking stuffer; so yess, I might get a couple.Thanks about the info. on the bit adapters; once I get one, I'll see if I can cobble up something.

-
Thanks for following

It's worth the 10$ I paid for it, and for someone just looking for a cheap MT that works it sure is a contender I would say
Looking forward to see if you can make a bit adapter work

Sent fra min FRD-L09 via Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login