Off brand challenge level 1
-
I have looked at these for some time but I pocket carry and they look like they are too wide for that. Interested to see how you get along with them.

-
You could do a lot worse for the money.

I'll do the 30 day off-brand challenge one day...
-
I am looking forward to you opening a can with this!

Or at least trying... The opener looks a little too far to the right.
-
If I can find one that doesn't have the pulltab I might try, maybe it's more suited for left handed opening

Sent fra min FRD-L09 via Tapatalk
-
-
Beeing a lefty I would too

Sent fra min FRD-L09 via Tapatalk
-
Day 3:
Just a quick pic, been a busy day.
The wire cutters work very well, clean cut of the thickest and thinnest stranded copper wire I could find

Sent fra min FRD-L09 via Tapatalk
-
And the pliers don’t get stuck doing so :D
-
Now this is good to know, and since they're an integral part of the jaw should be plenty strong; no more exploding replaceable carbide cutters!!!


-
Not sure how much abuse they will take but for electrical wires they should be perfectly fine

Sent fra min FRD-L09 via Tapatalk
-
Day 4:
The flathead works well as a screwdriver and prybar


Sent fra min FRD-L09 via Tapatalk
-
That's good news, some of those drivers twist round into little corkscrews then snap off

-
These are more good news, and looks like it is pretty squared and even; most C&C's I've seen tend to be somewhat rounded at the corners and at the tip, making them useless as screwdrivers.
I'll be waiting/watching for the phillips driver test, and if any of the square driver adapters work on it; I have Leatherman's RBD, Gerber's Tool Kit, and a couple of generic ones, and hope that at least one works with the Fatmax!

-
Day 5:
Used the pliers to adjust a fuse holder to fit the cables. The pliers did a good job


Sent fra min FRD-L09 via Tapatalk
-
Good to know!

BTW, Is the handle splay uncomfortable? From the action picture, it reminds me of the factory Rev/Wingman/Sidekick splay...
-
@Juan el Boricua said:
Good to know!
BTW, Is the handle splay uncomfortable? From the action picture, it reminds me of the factory Rev/Wingman/Sidekick splay...
I've never really figured out what all of you mean by handle splay
Is it how far the handles open in use?Sent fra min FRD-L09 via Tapatalk
-
Double post
-
@RF52 said:
I've never really figured out what all of you mean by handle splay
Is it how far the handles open in use?Sent fra min FRD-L09 via Tapatalk
Yes, that's it! I call splay how far, or close, the handles are from one another; a 1st gen. Gerber Multiplier has very little splay, and can pinch you if pliers slip and handles close ( but you'll be able to hold both handles while tackling a large bolt head, one handed). On the contrary, a Leatherman Skeletool has much more splay allowing for safe operation of the pliers, but can be difficult to turn or grab a large bolt head, probably requiring both hands. All this assuming that the person using the tools has small to medium hands, like myself. Large splay benefits people with larger hands, allowing a more comfortable grip to "squeeze".
-
Day 6:
These will atleast start off the day as my phone camera has started to act like a smurf. Might be able to get some action pics later.
Showing the handle splay opened and closed, a bit on the larger side for my hands (small to medium)


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login