3D Printer Blog
-
Any system is only as good as its weakest link.

Ok, this fine morning, I am printing a Yoda extruder knob. For the first time, I am looking at adding a raft and a different type of support...one that only builds a tower to support overhangs as opposed to supporting everything everywhere,
Trial and error continues, possibly with a lot of PEBKAC in the process. :ahhh
EDIT: I can tell from my initial raft layers that my right side of the bed is slightly out of level. I should probably halt everything, level the bed, and restart, but because I am experimenting with a raft, I am curious to see how this will turn out. So the experiment continues.
-
Ok..so this was the result.
<a href="https://flic.kr/p/2j3esKW" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49908373828_f8364938c5_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8477A by Chako, on Flickr
I think this part may need some painting down the road.
<a href="https://flic.kr/p/2j3iDhJ" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49909189702_4757d29c9d_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8478A by Chako, on Flickr
-
red is horrible for photography.
Concert pics with red lights

seems you defeated the pebkac this time in spite of the levelling issue?
-
I might paint it down the road.
-
It seem like you are off to a good start.
There are reference models available that tests various characteristics of your printer and material so it will be easier to find good settings, limits and orientation for parts and supports. (Typically some parts with various degrees of overhang, bridges, details and so on).
-
Do you mean the little tugboat called the Benchy? I haven't tried one of those yet.
-
No, there are models that are made specifically to have more gradual and systematic reference tests of common key points.
This test of some filament has one such model for instance (there are many):

You might want such a reference model that you can use as a consistent reference when you try out different materials and settings. A model with overhangs, bridges, thin bosses, holes in different sizes and directions, round parts.. I'm sure someone will have cooked up a fairly complete model by now?
Edit: This video seem to give some general ideas: https://www.youtube.com/watch?v=kgCjDy_IgXg (I didn't watch through all of it).
-
Oh I see. I will look into that further. So far, I cannot complain with the results I am getting. After doing a lot of reading, I knew there was a steep learning curve. What I didn't know was that most of it was going to be with the software.
Just finished printing another part to improve the printer. Not sure if this popular print is there to make the power supply fan quieter, or just for looks...but either way, I must admit is does look a lot nicer than a simple hole in the power supply. I even printed off the embossed version much like the much more needed control box cooling fan guard. I run a sharpie on the raised edges to pull out the details.
Yesterdays part with a bit of sharpie applied. This part is much needed to prevent plastic bits from entering and possibly damaging the mother board and the fan. Printed nicely with no supports, and only the obligatory skirt. I noticed that during my few days of use, the bed itself got out of level. The skirt...which is only a thin line that goes around the project, looked very thin on the right hand side. I was able to print this part as well as a extruder knob with no issues. However, I did not it was harder to remove the part from the glass bed. I learned something there. If the space is too close between the nozzle and the bed, it will be a lot harder to remove the part from the printing bed.
<a href="https://flic.kr/p/2j3rGnw" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49910760968_561a044a87_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8480A by Chako, on Flickr
Today's print with a few minutes to level the bed beforehand. I found it a lot easier this time to level the bed. Once again, I used no supports other than a skirt. This time around, the skirt looked really good. I fell asleep watching TV in the same room as the printer. When I woke, the bed and nozzle had already cooled down and all was finished. The part simply popped right off the glass bed. Another lesson there. I should wait for the bed to cool down before removing a part, as it should come off easier. Patience is a virtue. Here is the power supply fan silencer installed and sharpied.
<a href="https://flic.kr/p/2j3rGm4" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49910760883_aded56f067_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8481A by Chako, on Flickr
I am also learning just how much filament there is on a 1Kg spool, and just how many projects you can do with that much.
-
I haven't printed the power supply fan cover yet. Did it make it any quieter??
-
I think it did, but the fans on the extruder are still loud.
-
In the process of printing a storage drawer designed to fit the front empty space on the right between the LCD panel and the Y axis arm.
<a href="https://flic.kr/p/2j3DFHf" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49913100092_df54ac29ec_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8482A by Chako, on Flickr
<a href="https://flic.kr/p/2j3CadP" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49912802411_be105ccb8e_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8483A by Chako, on Flickr
My original plan was to do all the printer upgrades in black, and to learn with the red filament and to create my computer parts using it as my computer case is red. I ordered 2 black PLA 1Kg rolls of filament from Amazon, which was supposed to be in last Friday. Of course nothing is on time anymore because of COVID 19 and the probably big hit from everyone buying online these days. I will say, black and red for a 3D printer is a flashy combo, albeit not planned.
I had wanted a 3D printer for about 10 years now...and kept putting it off till prices went down, and the tech matured. I also wondered what I could possibly want to print or to put a 3D printer to use. Well now that I have one, the possibilities are limitless. I can even create simple parts from scratch using TinkerCad. Mind officially blown!
-
The print just finished, and it was a success. This will give me some much needed storage space and it is locked into the printer and slides in and out for ease of access.
<a href="https://flic.kr/p/2j3ETgU" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49913334102_9216982331_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8487A by Chako, on Flickr
<a href="https://flic.kr/p/2j3Dn8U" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49913037606_2a350b124e_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8486A by Chako, on Flickr
All that I think I need to do is to print out a tool holder that will hang off the gantry and I think I have the printer where I need it for now. I will print an LCD back protective cover once I get the BigTreeTech motherboard, then I can install the newer LCD that I already have...seeing that it has a USB and a SD card slot on the right hand side...which will be a big upgrade compared to the awkwardly placed micro SD card on the front.
-
Here is the tool holder. Lots of designs out there, but to me, placing it on the gantry is the best place. Surprisingly enough, the printer came with a pair of screws and anchors that were not required in the build...and this tool holder puts them to good use.
<a href="https://flic.kr/p/2j3MiS9" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49914587496_f084395250_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8491A by Chako, on Flickr
Room for a few extra drivers, etc.
<a href="https://flic.kr/p/2j3JLAT" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49914092103_62283d11d9_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8488A by Chako, on Flickr
-
That looks both handy and organized.

-
Agreed.
Painted quickly Yoda. The flash overpowered the brown on his coat and brought the red to the forefront. He looks a lot nicer in person. Now I have Yoda doing his little dance when the machine pulls filament. Kinda cute...and it is always a good thing to have the force with you at all times.

<a href="https://flic.kr/p/2j3PsQY" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49915007928_094e669e4f_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8494A by Chako, on Flickr
-
much better...
kinda glad I held back, back to Paris Monday

-
Shipments are all wonky right now anyhow. If it isn't Amazon holding on a package for a few weeks too long, it is Canada Post snailing it to me. I mean, packaged that linger at a location for a few days, etc. I know they are overburdened. It just is frustrating. I am still waiting for those 2 rolls of PLA which I was supposed to have last Friday.

-
I wanted to print a little flexi Rex key-chain last night, I kept getting a non-manifold error in Cura. When I sliced it, and reviewed it, it looked good. However, when I went to print it, I got a lot of spaghetti filament lay-down,.I aborted the print twice and gave up. I even re-leveled my print bed. I did that because the filament was not sticking to the bed as it should.
Well I woke up this morning and tried something else. That worked out great. So I take it anytime I come across a manifold error, I should drop it quick like a ticking potato masher and move onto something easier. I will look into what a manifold error is as well.

-
@Chako said:
I wanted to print a little flexi Rex key-chain last night, I kept getting a non-manifold error in Cura. When I sliced it, and reviewed it, it looked good. However, when I went to print it, I got a lot of spaghetti filament lay-down,.I aborted the print twice and gave up. I even re-leveled my print bed. I did that because the filament was not sticking to the bed as it should.Well I woke up this morning and tried something else. That worked out great. So I take it anytime I come across a manifold error, I should drop it quick like a ticking potato masher and move onto something easier. I will look into what a manifold error is as well.

Non-manifold errors are usually caused by the 3D modelling not being clean (as in keeping it simple with just the operations needed), not being tight (as in waterproof solid models) or tolerances being too large for the printing program to accept joined edges as actually being joined. (That said I think some 3D printing programs might introduce some issues all by themselves with less than optimal slicing).
Once you start doing your own 3D modelling you can make your own stuff and avoid faulty models.

-
10-4.
Today, I printed 3 ear savers for mask wearing. They turned out very nice.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login