3D Printer Blog
-

this one...
-
I was thinking this one. I guess it is more for starting fires:

-
Found a problem...and I looked online for a solution, and just finished emailing Creality. I was about to play with the little CR-100 in Cura when I found out it did not have a profile. I looked at all the electronic files that came with the printer's micro SD card...and all I could find was info for a CR-10 which is a totally different printer. I played around with Cura and figured out where I could make a custom profile, but I do not have all the parameters. I know the build size is 100 x 100 x 80 mm, and that the nozzle is 0.4, and that is about it. I have no clue on start stop parameters, X,Y, and Z settings, etc., I couldn't find anyone online with the info I needed. I emailed Creality and see if they will respond.

-
@Chako said:
Found a problem...and I looked online for a solution, and just finished emailing Creality. I was about to play with the little CR-100 in Cura when I found out it did not have a profile. I looked at all the electronic files that came with the printer's micro SD card...and all I could find was info for a CR-10 which is a totally different printer. I played around with Cura and figured out where I could make a custom profile, but I do not have all the parameters. I know the build size is 100 x 100 x 80 mm, and that the nozzle is 0.4, and that is about it. I have no clue on start stop parameters, X,Y, and Z settings, etc., I couldn't find anyone online with the info I needed. I emailed Creality and see if they will respond.
Creality have their own slicer? (I have no clue, but I do see this: https://www.creality.com/u_file/1911/photo/e0840a8e91.png. That, whatever it is, has a CR-100 profile it seems?
-
Ok. I decided to install the slicing software included with the CR-100, even though it is a far older build of Cura modified by Creality. Lo and behold, there is a CR-100 profile included with this. After using the most current version of Cura, I am not really liking this older interface. Cura 4.6.1 is far more polished than this 1.3 Creality version. Now, I have dug deep into the Creality slicer and am trying the included lion file for now. Better yet, I have dug into the various aspects of the slicer and found a lot of info that I could possibly transplant into Cura 4.6.1 I will look into this as a possible custom profile. Ideally I would rather use one piece of software for both printers.
Got the first print going...
<a href="https://flic.kr/p/2j6iDD6" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49943140371_8bea47b644_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8522A by Chako, on Flickr
Non heated bed...so rafts are the thing I guess.
<a href="https://flic.kr/p/2j6g3k6" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49942631363_2657e1ab97_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8525A by Chako, on Flickr
I now feel much better about possibly having a profile for the CR-100. I did email 2 places...and will see what the response will be if they respond.
EDIT: Vidar, both on the same page at the same time.

-
A few first impressions as it prints. the nozzle heats up quicker than that of my Ender 3. The printer is much quieter in that the extruder fans aren't as loud. The stepper motors are about as loud as that of the Ender 3. I will have to print a larger spool for this machine. Not sure why they only allow smaller filament spools on this thing. The printer came with 200g of white filament. The spool holder will not fit a 1Kg spool...but there are a few mods I found over at Thingiverse that will fix this issue. Still a really cute looking printer. I bought this to see if it might make a good classroom printer. Noted they use the same plastic filament feeder mechanism as on the Ender 3. I might have to get myself another all metal kit to upgrade this. I have seen online photos of wear and tear of plastic parts that eventually get eaten by the filament. The metal kit prevents this from happening.
Still a bit surprised that the current Cura 4.6.1 does not have a built in CR-100 profile. This tells me that the little cute printer might not be selling all that much.

-
First print was a failure. I didn't clean the bed with my alcohol wipes. Noticed the raft was actually designed with little contact on the bed. Going to play with the settings tomorrow if I get the chance. What did print was good, but it let go about half way to completion.
-
@Chako said:
First print was a failure. I didn't clean the bed with my alcohol wipes. Noticed the raft was actually designed with little contact on the bed. Going to play with the settings tomorrow if I get the chance. What did print was good, but it let go about half way to completion.I've never tried a non-heated bed, but I imagine that might come with some challenges too.
I've made lots of half-prints, messy prints and random treaded nests. Until the settings are right (if ever) that comes with the territory. (I think some 3D printer and material manufacturers have some curated settings that should work for their combination).
I generally prefer the resin printer. :D
-
Creality stating that the CR-100 has auto bed leveling is a BIG FAT LIE. I just attempted another print and I could tell right away that the nozzle is extruding too far away from the build plate resulting in an immediate lifting of the raft on the model. I took a gander at the instructions once again and noted that the nozzle assembly is on a spring loaded gantry, and that there is an adjustment screw for the gantry...however the access hole is covered by the filament spool. I gather I will have to adjust the screw with a piece of paper between the bed and the nozzle. Can't adjust 4 corners like the Ender 3. Little written in the instructions about leveling this printer. So much for being a "kids" easy to use printer right out of the box with auto leveling. The CR-100 is harder to adjust and is not as user friendly as the Endeer 3...go figure.
-

Sounds like a case of the cheap stuff needing more tinkering? :(
-
@Don Pablo said:

Sounds like a case of the cheap stuff needing more tinkering? :(
I've always found this entire leveling thing, automatic or not, as an indication that 3D printers don't have the best structural solutions. Other machines that needs their worktables to stay level seem to manage that just fine - set once and forget. Well, I guess expensive 3D printers don't have that issue either. Likely a cost thing.
-
@Vidar said:
I've always found this entire leveling thing, automatic or not, as an indication that 3D printers don't have the best structural solutions. Other machines that needs their worktables to stay level seem to manage that just fine - set once and forget. Well, I guess expensive 3D printers don't have that issue either. Likely a cost thing.Agreed.
When was the last time you used a milling machine that cost 300? :ahhh -
That sounds about right. The Ender 3 is a breeze to level because of its open design.
On the plus side, I received my BigTreeTech SKR Mini E3 main board today. That means, when I am up to it, I will upgrade the main board and the LCD. This will be a huge improvement if it all works. I have to laugh though...the board came in and it is so small. It is designed to replace the existing 8 bit board, upgrading it to 32 bit with more RAM, and a lot of extra goodies such as a BL Touch connector on the main board replacing the inelegant daughter board that comes with the BL Touch kit for the Ender 3. Upgraded OS as well. There are a few more benefits...which the video will go into greater details...if you are interested in watching it.

- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
-
@Don Pablo said:
Agreed.
When was the last time you used a milling machine that cost 300? :ahhhMilling machine and milling machine... I got a cheap milling table some time ago for a project. It just didn't work. The table got stuck trying to move sideways. I tried to fix with some gentle swearing, a hammer and various screwdrivers. Now it is really stuck. On the positive side I now have some spare parts which magically appeared.
No, price of course have a lot to do with it. But I'm not convinced that is the entire story.
-
Got into a spot of trouble with the Ender 3. I changed filament from red to black. Amazes me I sill have a bit of red left after all those print jobs. Anyhow, I did something I now know I should not have done, and I learned from my mistake. There was about and inch of black filament that was kinked because if was pushed through a side hole of the spool during shipment to prevent it from unraveling. Instead of cutting off that inch, I just trimmed the end to feed it through the extruder. What followed was a bit of fun as nothing would print correctly, not to mention I was getting strings and glop forming. I re-leveled the bed to no avail. I couldn't figure it out. I even took the fans off the nozzle and cleaned the nozzle with one of those acupuncture needles. I was a bit frustrated and left it for this morning. Today, I tried another print and all worked as expected. The only thing I can figure out, was that the kinked filament caused me grief. Note to self, don't be a scrooge, trim that bent area next time I feed another spool of filament into the printer. I can only assume the bent filament section was fed through the extruder and all is good now.
This is what I was getting. Not an even layer of filament laid down, it would sputter, and ultimately not adhere to the heated bed. Luckily enough I stopped several print attempts quickly.
<a href="https://flic.kr/p/2j7Nche" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49960026441_4b2cf78a23_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8526A by Chako, on Flickr
And this morning...back in the black. Sorry I couldn't help myself with that bad accounting pun.
<a href="https://flic.kr/p/2j7Ncfq" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49960026336_4235a404cc_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8529A by Chako, on Flickr
I hope all goes well to completion of this test kitty.
-
50% and so far so good.
<a href="https://flic.kr/p/2j7Re2w" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49960617652_16274dffea_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8532A by Chako, on Flickr
I still haven not played with my little CR-100 as of yet. I am thinking I may need to get a glue stick or something. I never understood how important a heated bed is for adhesion, or is that the glass is a far superior surface. I may have to look into getting a glass sheet for it down the road...maybe. It is small compared to the not all that large Ender 3 which I consider a medium sized machine.
<a href="https://flic.kr/p/2j7Meyh" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49959838988_e4246760e0_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8533A by Chako, on Flickr
-
Ok...the piece let go 3/4s of the way. I examined the base and there was little material there. I think before I should try another attempt, I will have to delve deeper into the base and fill rate settings. I am more than happy that I am no longer having weird extruder issues however. As it stands, I can use this cat as a pencil holder or something, seeing that it is hollow.
-
@Chako said:
I never understood how important a heated bed is for adhesion, or is that the glass is a far superior surface. I may have to look into getting a glass sheet for it down the road...maybe.I know from frustrating experiences that some materials are very sensitive to the heated bed temperature - as little as a few degrees here or there makes a difference.
I might be wrong about this, but I think a non-heated bed is basically limited to a smaller selection of materials. On the upside it should work fine with those though.
-
I had a successful print of two utility knives however the tolerances between the two pieces are such that when I attempted to put them together, they got jammed.

However, the model did not come loose from the heated bed...so that is a good thing. I am going out today to buy myself some glue sticks to try that out.
-
Ok...I got fed up yesterday and decided to visit the local Walmart to find some glue sticks. I was able to procure some Elmers purple glue sticks. I tried it last night with an immediate failure. I rubbed the stuff on the glass plate and immediately cleaned it off with some alcohol because I had read someone on a forum somewhere stating they had great success doing this. I should have listened to my gut feeling. It failed. I took the glass plate off of the printer and washed if off really good. The textured side I used was a bit hard to clean very well. I decided to flip the glass over and print on the smooth surface. This time, I followed other directions to warm the bed up to temp and to put a layer of glue stick on...and to wait for it to dry. That appears to be working very well. I am in the process of printing off a figurine to test this out.
In the mail, I got my all metal upgrade extruder kit. Time to upgrade the little CR-100's plastic extruder.
Here is the plastic one. I am told that the filament wears a hole where the filament and plastic rubs together.
<a href="https://flic.kr/p/2j8spFw" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49967482416_eaa741869e_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8534A by Chako, on Flickr
Here is the metal upgrade kit.
<a href="https://flic.kr/p/2j8spEu" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49967482356_63cdf20aa6_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8536A by Chako, on Flickr
Installation was super easy, probably because it was my second kit install.
<a href="https://flic.kr/p/2j8tN7C" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49967752992_fe229071b8_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8537A by Chako, on Flickr
I have no idea what I am printing here as I am trying out the glue stick on the surface. I flipped the textured side over and rubbed glue on the smooth metal plate. Seeing as this is a non heated bed, I am curious to see if this will work. So far, it is the furthest I have gotten on a print with the CR-100. X fingers.
<a href="https://flic.kr/p/2j8spCf" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49967482226_b134b5dd05_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8540A by Chako, on Flickr
The little CR-100 does not appear to have to many upgraded pathways unlike the Ender 3. From what I can see, the metal extruder kit might be just it.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login