3D Printer Blog
-
Started to print upgrade parts for the second printer before it gets here. Note that the bed is not exactly leveled as the right side is a touch too close to the nozzle as evidenced by the skirt. My next print will need a bed re-leveling adjustment on that right side.
<a href="https://flic.kr/p/2jm7tLp" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50110708363_495e559c81_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8682A by Chako, on Flickr
-
Got another upgrade package in the mail yesterday, and I just finished installing it. I think this is a much better solution to the Y-axis tightener. The original piece requires 4 screws to be loosened and then the whole unit to be pulled to catch up any slack in the Y-axis belt. The new piece is much easier to tighten via a knob.
The old...
<a href="https://flic.kr/p/2jmbCWF" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50111519683_93caab0862_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8683A by Chako, on Flickr
The new...
<a href="https://flic.kr/p/2jmfLiF" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50112324897_fe60bf10fb_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8684A by Chako, on Flickr
Oddly enough, there was no instructions that came with the upgrade. I had to work from a photo online. A simple set of instructions would have gone a long way, especially in my figuring out how the pulley system was put together. I managed...but it took an extra 15 or so minutes for something simple.
One thing to be mindful, this will not fit on an Ender 3 Pro with its dual width beam on the Y-axis. They make a wider version for the Pro.
-
Canada Post up to its usual again. The new printer and motherboard where slated to arrive this Friday. Checked this morning, and the motherboard is delayed once again in Sudbury. Same message with the printer, stating that it might arrive Friday, but don't count on it. Sigh.
-
I decided to print a storage drawer for the new printer. Because the Pro has a 2040 Y-axis aluminium extrusion compared to the Ender 3X's 2020 Y-axis, I had to make sure I am printing a drawer designed to fit the pro.
Because I liked the one I printed for the Ender 3X, the Pro version should fit the bill. I like how it slides in and out, and that cutout in front gives a lot of access to the bed leveling knob on the front right corner.
Starting 7 hour print.
-
Call me swift. I was thinking about future projects when I decided to type in "Swiss Army Knife" in the search query on Thingiverse. Looks like I may have to play with some of this in the future.

-
Got home to a power outage. I sat in the dark looking at my dead printer for 27 minutes pondering if the printers resume feature will work, or will I have to trash my drawer. Power came on, and the printer asked me to resume. When I pressed yes, the printer auto homed the nozzle. Problem..the printer did not raise the nozzle...and when the power shut off there was a bit of pooled plastic. After a bit of resistance and noise, the nozzle went to home. The printer then heated the bed and the nozzle, and continued once again with the project. While the printer heated things up, l cut the pooled plastic with a pair of side cutters. Only time will tell if the results are good. I thought I would never have to test this printer feature. It works, but there is a chance when the nozzle auto home's to knock the piece off the plate due to the plastic that pools onto the project.
It does work though.
-
Here are some photos of the drawer that suffered the power outage.
Resume print does work...albeit, it did leave some artifacts.
<a href="https://flic.kr/p/2jmJV3Z" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50117817457_658e8dbe05_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8685A by Chako, on Flickr
Here is the finished product. At least I didn't lose 3 hours of printing, but you can tell the layer that resumed.
<a href="https://flic.kr/p/2jmERAT" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50117025403_296a992c16_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8686A by Chako, on Flickr
<a href="https://flic.kr/p/2jmHLfE" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50117592746_91a92c305f_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8687A by Chako, on Flickr
Happy to say, this is a utilitarian drawer and the line doesn't bother me in the least. Just happy that I didn't wast any filament. So yes, the resume print feature does work...just do not expect to get a perfect piece in return. If this was a decorative object, I would not be very pleased.
Speaking of not being very pleased, Canada Post is up to their usual once again. I have 5 Amazon.ca shipments tied up in Sudbury. Sudbury is a 3.5 hour drive from where I currently am. All my shipments were slated for July 17 or 20th arrival. Just checked and am told that they might still arrive on time, but there was an external delay. From past experiences, I am thinking the delay may be sometime late next week if I am lucky. Time will tell. Just wondering why Sudbury seems to be a sticking point for local deliveries.
In case you might be wondering, I have the following doing the Sudbury crawl...
- Creality Ender 3 Pro.
- BigTreeTech SKR Mini E3 motherboard.
- 10 608ZZ ball bearings used for upgraded spool holder which I haven't printed yet.
- BigTreeTech TFT35 E3 V3.0 LCD screen. I know I wasn't originally going to get one for this printer, but thought I should try to keep both printers consistent for ease of use.
- X-axis belt tightener.
-
That is a neat feature. :) Not sure what mine would do in such a case - hopefully something similar, but I also hope to never find out.

-
It is something I never wanted to try out. At least I now know what to expect.

I found out I can print SAK toothpicks. I will have to try that out now.
-
Success...and 3 of them only took 3 minutes to print.
-
Took another gander at the arrival dates. A few packages have now arrived in my city...possibly get them tomorrow maybe.

-
That was a surprise. I received my Ender 3 Pro just now.
<a href="https://flic.kr/p/2jmXBJJ" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50120295666_bdc16b2600_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8689A by Chako, on Flickr
-
I am going to build it once I get the rest of the parts in. If all goes well, the motherboard should arrive today, and the rest on Monday. Fingers crossed.
-
Well...there might be something to building it first to see if it all works, and then upgrade things. I just got everything out of the box.
Laid out, looks exactly like the Ender 3X. There are a few things different, but I do not think the "Pro" designation means this is a professional 3D printer. It still is an entry level printer that gives fantastic results.
<a href="https://flic.kr/p/2jn8qft" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50122208143_6dd8b33302_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8694A by Chako, on Flickr
The Ender 3X came with a glass plate as standard. I have read a lot about this magnetic build plate that comes with the Ender 3 Pro, and a lot of folks do not like it. I already bought a spare glass plate which I think will ultimately get put on there. I am curious to see how this magnetic plate works. I can tell that removing it is easy, but putting it back on the other glued on magnet is troublesome to alight it correctly. I also read that a lot of people just remove the top magnetic mat and place the glass plate right on the glued magnet. Not sure If I will like that...or if I will attempt to peel that magnet layer off of the aluminium heated bed. I have also read that if you go above 80 degrees, it kills your mats magnetism. This could be an issue for other printed materials. Thus far, I have only gone to 60 degrees with PLA.
<a href="https://flic.kr/p/2jnbjgg" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50122773341_53edd9289b_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8695A by Chako, on Flickr
Looks like the nozzle part is exactly like my Ender 3X. Not sure if the original Ender 3 has a different end or not.
<a href="https://flic.kr/p/2jncsxv" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50122996307_a7dc43f690_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8696A by Chako, on Flickr
A lot of review sites seem to put a lot of points on the upgraded Meanwell power-supply of the Pro version. All I know is that the one that came on the Ender 3X is thicker, and I haven't had any issues with it at all. This Meanwell power-supply is thinner for sure. If you look at the second photo here, the old 3X power-supply is as thick as that bottom plastic shroud.
<a href="https://flic.kr/p/2jn8q1F" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50122207343_cf7860a122_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8697A by Chako, on Flickr
<a href="https://flic.kr/p/2jn8pWx" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50122207103_6de24c0c37_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8698A by Chako, on Flickr
The other big upgrade (or so I am told) is the Y-axis aluminum extruded beam which is now 4040 as opposed to the 3X's 2020 sized beam. The wider 4040 on the Pro should help the stability of the heated bed...although I have never encountered any issues with the 3X's 2020 Y-axis beam. I suppose bigger is better and will be a good upgrade. Also note in the picture the motherboard box has been reversed. This means I will have to put the printer on its side to access the compartment from underneath. This also puts the USB connector and Micro SD card higher off the ground. I didn't mind the lower access as I have the printer in line with the front of the table. At least no plastic bits can fall into the cooling fan in this configuration.
<a href="https://flic.kr/p/2jn8pS9" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50122206848_33cf3a2478_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8700A by Chako, on Flickr
Oh my gosh. The Pro has the same plastic extruder assembly as the CR-100 and Ender 3X. I would have thought this part would be all metal for the Pro model. Guess I will have to order another metal one for 20 bucks.
<a href="https://flic.kr/p/2jncseV" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50122995287_86982e28e4_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8701A by Chako, on Flickr
So there you have it.
-
Good day indeed. Just got in both the motherboard and LCD screen along with the X-axis tensioner.
-
Time to slowly start this. I plan on finishing tomorrow hopefully. First thing...now that I have a few key upgrades at hand before building the printer, I might be able to do them in a logical sequence that might necessitate less work on my part.
First thing is first, to install the new stiffer orange bed leveling springs. It is so much easier to flip the bed over without having to worry about the gantry getting in the way. Still a spaghetti mess of wires on the one corner. You can see the upgraded spring in place...and the original one just south of it. These upgraded springs are stiffer and should hold your leveling better compared to the weaker originals.
<a href="https://flic.kr/p/2jnfY6x" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50123681057_f74a22f70b_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8702A by Chako, on Flickr
Seeing that I now have the printer on its back...time to start changing the motherboards. I will get this cleaned up and will finish the transfer tomorrow. I ran into a small minor issue. There are 3 screws holding the plate on...however, the bottom plate would not come off. I flipped the printer over on the right side and found another screw that I had to remove...on the Ender 3, there was only the 3 screws. Here is the original motherboard all hooked up.
<a href="https://flic.kr/p/2jnfXZf" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50123680692_739875c78d_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8703A by Chako, on Flickr
Much like my Ender 3, they hot glued everything in place. Always a bit of a challenge and fun to remove the hot glue. Here I am starting to remove the cabling on the original motherboard. Yes, both the Ender 3X and the Ender 3 Pro feature the same noisy 8 bit motherboard version 1.1.4. Good thing I will be replacing it with a sweet BigTreeTech SKR Mini E3 V1.2 motherboard.
<a href="https://flic.kr/p/2jnePQf" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50123458146_832484e93c_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8704A by Chako, on Flickr
Time to prep the replacement. I have to place the blue heat-sinks onto the stepper controllers.
<a href="https://flic.kr/p/2jnbVxv" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50122892023_78df905699_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8707A by Chako, on Flickr
That quick and easy job is done.
<a href="https://flic.kr/p/2jnePC1" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50123457436_d22bd3610b_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8709A by Chako, on Flickr
That is it for tonight.
-
Today was a bit fun, and I am not exactly finished yet. I sill need to update the motherboard firmware, and not all went as planned.
First thing when I woke up was to remove the old board and install the new. Here are both the Creality V1.1.4 board on the left, and the BigTreeTech SKR Mini E3 V3.0 board on the right.
<a href="https://flic.kr/p/2jnp6Sj" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50125268098_9d024facf8_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8711A by Chako, on Flickr
I forgot an important step and installed the new board into its compartment.
<a href="https://flic.kr/p/2jnp6LT" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50125267783_809e26cedd_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8712A by Chako, on Flickr
Oops. I forgot to install the power leads first as they are mostly impossible to install when the board is screwed down in place.
<a href="https://flic.kr/p/2jntas6" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50126060597_0622f29854_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8713A by Chako, on Flickr
Once done, it is a simple manner of screwing down the motherboard and complete the wiring.
<a href="https://flic.kr/p/2jns38n" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50125840851_6a867d0d85_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8714A by Chako, on Flickr
Here is the bottom compartment plate. Plenty of ventilation holes compared to the one found on the Ender 3.
<a href="https://flic.kr/p/2jns35m" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50125840676_20d9aa43de_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8715A by Chako, on Flickr
Here I am installing the new LCD screen, which I found does not work as advertised. I am uncertain if it is a wiring issue on my part, or the part just shipped damaged. I have 2 white lines running perpendicular, and the whole display is so light I can barely read it. I might have to sent this part back, but I want to play around with it a little more...but not for today. I re-installed the original display and that works great.
<a href="https://flic.kr/p/2jnp6qc" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50125266583_04c7d04163_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8716A by Chako, on Flickr
After installing the gantry and the extruder, bowden tube, and nozzle assembly, time to install the few key printed upgrades.
<a href="https://flic.kr/p/2jntaaT" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50126059657_b5fe8d41fd_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8719A by Chako, on Flickr
Last to be installed is the Z-Axis bracket.
<a href="https://flic.kr/p/2jnta6j" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50126059392_e1e7bc52d1_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8720A by Chako, on Flickr
The completed Ender 3 Pro on the left, and the Ender 3X on the right. I still have a few more things I want to upgrade. I did try the printer after leveling the bed and it works good. I installed the glass plate immediately as it ensures a flatter surface for leveling. Those puck lights I Velcroed to the underside of the gantry have caused problems. Gravity likes to make them fall as the glue fails. I will have to look at another solution that won't endanger a print in progress.
<a href="https://flic.kr/p/2jns2Mx" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50125839701_ceebba0cc6_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8722A by Chako, on Flickr
Next steps is to update the firmware, and play around with the BigTreeTech TFT35 E3 LCD. If I cannot figure this out, I may have to ask for another and return this one back.
-
Loving following this thread and seeing your progress and prints!
What are is the gantry made of? If you're having issues with the lights sticking then magnets may be better if it's a ferrous metal or zip ties if it isn't.
-

Aluminium. Zip ties might be the way. I have noticed however that these LED puck lights eat through 3 AAA cells like nothing. Because of this, I am thinking of something that uses a plug in. As I am typing this up, I remember that I have 2 lights upstairs when I did my leatherwork that are not in use. I may have the solution already.

-
Without the writeup and skipping a few of the pics the story might have looked as if the one printer printed the other one :D
Nice work!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login