Daredevil Challenge 2021
-
@ReamerPunch said:
Day 13I had a piece of wire on my bowdrill, to keep the spindle in place, when getting into position. But it was a little loose and it bothered me. I removed it with the pliers, and put a screw in place. Nice and firm, no rattling, and I can remove it easily if I want to. The Phillips bit nicely into the screw and drove it with no issue, other than subpar ergonomics.

You lost me at "piece of wire" ::) (very good use
) -
@Alan K. said:
Day 13
Stuck in traffic earlier this morning, but now safely back home.Is it acceptable to whip out your tool and display it on the dash for awl to see

-
@Humayd A R Mahomedy said:
Day 13
20210813_141502 by Humayd a r Mahomedy, on Flickr
i got this SRK from a buddy who decided to pull off the handle and glue it back on with "sticks like smurf". he used a fastener in the lanyard hole.
this arrangement bugged me until i decided to use a tube to line the lanyard hole.
pictured is my 3rd or 4th attempt,i keep cracking the tube when i try to flare it.
20210813_141748 by Humayd a r Mahomedy, on Flickr
the Swisstool worked,i was a bit concerned about the "hybrid" pliers,but it did what was needed just fine.
20210813_142452 by Humayd a r Mahomedy, on Flickr
i used a thin-walled stainless tube,this side is passable.
20210813_142456 by Humayd a r Mahomedy, on Flickr
this side is fudged.
back to the drawing board
20210813_164545 by Humayd a r Mahomedy, on Flickr
i used the serrated blade to open a bag of cat food,it zipped through
I wouldn't even know where to start 
-
-
@cody6268 said:
Day 12; got into some stuff to start a computer repair kit. I own few decent screwdrivers, so I picked these up. I have seen this USA-made design under several different names over the years, but they are most associated with Klein. Same screwdrivers, just blue acetate and not yellow.
Nice 
-
No use at all today. :(
Went to an estate sale this morning, but no SAKs. Just some cheap Chinese multi-tools. (Too bad the sale wasn't last month. I would have been set for the challenge!) The house was a hoarder's house. It was...interesting.
Spent the afternoon watering the parched lawns. They aren't liking the near 100 degree temps. The S557 was no help with that.
So just a photo of the S557 posed with some other members of my collection. See if you can identify them!
That's a lot of tool... 
-
<u>Day 13</u>

TGIF, been a pretty busy past two days, and am really looking forward to the weekend. Here's Wetols helped with snack duty this afternoon.
-
-
-
-
-
@Echotech said:
Thanks Fireman

I spoil her rotten anyway :D but she’ll be getting lots of extra attention that’s for sure.
Here’s her earlier in the week, be glad to have her back to her stick chewing self


I maybe a day late, but do hope Coco is back to her usual self by now.


A nothing sort of day where I spent several hours trying to get one of our baggage x-ray machines going ::)
I seemed to prevail and needed something to test it on; step forward the OHT

Looks like the OHT may have a life in modeling, who would have guessed that...
:D -
-
No use at all today. :(
Went to an estate sale this morning, but no SAKs. Just some cheap Chinese multi-tools. (Too bad the sale wasn't last month. I would have been set for the challenge!) The house was a hoarder's house. It was...interesting.
Spent the afternoon watering the parched lawns. They aren't liking the near 100 degree temps. The S557 was no help with that.
So just a photo of the S557 posed with some other members of my collection. See if you can identify them!
Champion c, Bijou (2), Classic SD (5), Cavalier, Mini Champ (2nd gen.) Plus (mod), Swiss Champ (2), Explorer (2), Deluxe Tinker, Climber, Pioneer Alox, Bantam, Delemont Evolution S557, Wenger Serrated Commander, Huntsman, Serrated Spartan/Weekender, Executive, Explorer Plus, Deluxe Explorer Plus (mod), Wenger Traveler
I will give it a try...from left to right:
Deluxe Tinker, Explorer, Deluxe Explorer Plus (mod), Champion C, Swisschamp, MiniChamp?@ReamerPunch said:
Day 13I had a piece of wire on my bowdrill, to keep the spindle in place, when getting into position. But it was a little loose and it bothered me. I removed it with the pliers, and put a screw in place. Nice and firm, no rattling, and I can remove it easily if I want to. The Phillips bit nicely into the screw and drove it with no issue, other than subpar ergonomics.

Any success in the friction fire? I have watched enough survival show and did a few practices myself, and am fully convinced I really, really ought to carry some form of ignition device whenever going outdoor. There are just too many factors in making the friction fire that it is best kept as a backyard project, instead of me trying to count on it(or myself).
-

Glad to see Coco seems to be doing a little better. This pot is pretty scary, perfect for halloween!
@Sos24 said:
Day12
The Minimaster helped with putting a split ring on a flashlight.

It then cut open a snack

Is this new or the Rovyvon repainted?

@Fireman said:
Daredevil Day 13: Sunrise at the beach. 8)
Beautiful settings!

My grandson didn't have much good to say about the saw either. He wanted the Super Tool




I foresee a future MTOer in this one, so cute and smart too! 
-
@Humayd A R Mahomedy said:
Day 13
20210813_141502 by Humayd a r Mahomedy, on Flickr
i got this SRK from a buddy who decided to pull off the handle and glue it back on with "sticks like smurf". he used a fastener in the lanyard hole.
this arrangement bugged me until i decided to use a tube to line the lanyard hole.
pictured is my 3rd or 4th attempt,i keep cracking the tube when i try to flare it.
20210813_141748 by Humayd a r Mahomedy, on Flickr
the Swisstool worked,i was a bit concerned about the "hybrid" pliers,but it did what was needed just fine.
20210813_142452 by Humayd a r Mahomedy, on Flickr
i used a thin-walled stainless tube,this side is passable.
20210813_142456 by Humayd a r Mahomedy, on Flickr
this side is fudged.
back to the drawing board
20210813_164545 by Humayd a r Mahomedy, on Flickr
i used the serrated blade to open a bag of cat food,it zipped throughThird picture from top, it was so close! You are almost there, keep up the great work!
@SurgeUk said:
Is it acceptable to whip out your tool and display it on the dash for awl to see

Ever since you mentioned the 'lewd' comment in a previous post, I can't shake it and just curious anyone else read this comment funny like me?

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



Oh, wait... ::)
