EDC Bit Ratchets
-

PK Tool Mini Ratchet
(Can also be found branded by Budnitz, Fortis, Katana, Rujoi, Signet, Sonic, and Smato.
Same size and basic design as the Blue Point, Granite, KS Tools, PowerTorque, Topeak)Max torque rating: 30 Nm / 22 ft lb
Weight: 29g
Length: 93mm
Head width: 15mm
Head clearance with standard bit: 25.5mm (adds 0.5mm)
Teeth count: 52
Minimum swing arc: 7°
Bit retention: spring
In-line driver retention: magnet
Handle material: Chromium-Vanadium steel
Price: $15, just for the toolAccessories
The PK ratchet did not come with anything else. The exact same ratchet can be found under many brands, so it can be found in different sets.
Dimensions
This is extremely lightweight, at only 29 grams. It is also very compact, with a narrow stem and the narrowest head available.
Teeth Count
The PK has 52 teeth and a 7 degree swing arc. Quite good considering how small the head is.Bit Retention
The PK has a spring in the ratcheting end. This spring is quite strong, making it somewhat difficult to remove bits with thin ends. It helps to push the bit out from the back while pulling from the front.
There is a magnet in the in-line driver socket. This magnet is also quite strong, and stubby bits and bits with thin heads may not provide enough purchase for fingers to remove them.Bit compatibility
Stubby bits may prove difficult to remove from either end.
Standard double-ended bits cannot be used in the in-line socket. They can be used in the ratcheting socket as long as one end is thin enough to fit through the hole.
Leatherman bits barely engage in the in-line socket and are able to move significantly from side to side. They can be used in the ratcheting socket if one end is thin enough to fit through the hole, and if they are installed with the retention spring engaging the two notches on the bit to secure it.
Bits and extensions with grooved bases do fit the ratcheting socket, but the retention spring does not engage, so there is a lot of play, although they will not fall out.
Switch action
The PK has a small -arguably too small- and low-profile switch with good detent, so the action will not get reversed accidentally. The switch tail rests in a scalloped area, which guides the thumb left or right, to make operating the switch easy.Ease of use
The PK has a very strong spring. Bits that have the side notches have to be pushed from the back while pulling from the tip. The in-line driver magnet is also arguably too strong, and stubby bits are impossible to pull out with my fingers. The ratchet action switch is low-profile, and does not get moved accidentally. The stem is very slim, but it provides decent amounts of torque. The ratcheting head has a knurled wheel, to quickly turn screws with your index and thumb once there is little to no drag. When using the in-line driver slot, there is no knurling to add traction.
The ratcheting head is the narrowest, and it will get in tight spots. The teeth count is high enough for a very low swing arc, so it will still manage to turn screws with limited space to swing the tool. Both bit slots are deeply funneled, to make installing bits easy.
The spring is also holding the ratcheting mechanism in place, and can be removed, should the unit require maintenance.
Construction Quality
The PK has excellent fit and finish; very little ratchet socket wobble in the frame, no grind marks or other imperfections of any sort. Everything is chamfered, polished, and precise. The ratchet switch has no play, bits fit very well with negligible wobble.
The ratchet mechanism works beautifully, with no grinding, no grittiness, it does not skip teeth; the action is consistent and the tolerances are precise.Portability
The PK is extremely slim and lightweight. The stem is minuscule, which makes the tool perfect for edc pouches with elasticated webbing. It will disappear in any pouch or pocket, and it fits in the narrowest of pen slots.
Thanks to the hole in the back of the ratchet head, a carabiner or quick release clip can be used to attach the tool to a key-chain or pack.
Value
This would seem expensive considering it does not come with bits or anything else. Still, ratchets of this size (Liv, Giant, Topeak, Granite, Katana, etc) that do come with bits and cases are typically more than double the price of this. If you are only looking for a ratchet, this may be preferable to something similar that may leave behind an unused case or other accessories, that will cost a lot more.Conclusion
When it comes to edc ratchets, this is hard to top. It will take the least amount of space and add a negligible amount of weight to your kit. There are others that cost less, but will be inferior to this one's quality, and also bulkier and heavier. There are others of this exact size that do come with bits, accessories, and cases, but they will cost at least double what this does. This is the least expensive option for a tiny, high quality ratchet.Note that the exact same tool can be found under many brands with different bit kits and cases, so it would pay to shop around if you want this with accessories.
Pros
-Excellent fit and finish.
-Absolutely tiny.
-Knurled disk allows quick turning of loose fasteners with fingertips.
-Ratchet end compatible with many double-ended bits.
-Thin and narrow head combined with high teeth count can work in the tightest of places.Cons
-None.If you liked this ratchet, also check out:
-
^ That's pretty much what I was gonna say about the Topeak.
One thing I have found is that the inline driver, the lack of knurling really robs you of grip and power... but a sleeve of Sugru built up flush with the driver end, with some ribs or chequering laid in with a credit card edge, before leaving it to cure overnight, does work rather well!!

-
@m47mu74nt said:
This thread is going to be super interesting !
I carry the Victorinox ratchet, and the only complain I have with it is the incompatibility with Leatherman bits on the inline slot.I've been curious about the Victorinox ratchet. I am not a fan of pass-through ratchets, though. Not to mention this is quite expensive to get. But I'd like to get my hands one one, if only to try it out.
-
@GearedForwards said:
I don't know why, but something always looked 'wrong' about those flat form factor ratchets
Enjoying the thread, I've wanted a Topeak ratchet for years but never jumped on it, this might show some good alternatives

Yeah, those cheap flat ratchets are all over the place. You can even find it with no brand, that's how cheap they are.
The Topeak on the other hand, now that's a ratchet. A bit expensive to get, and I do not want bike-specific tools with it. I haven't seen any set with just the ratchet, bits, and case, and maybe an extension. Well, I actually have, but it was not branded by Topeak.
That's the interesting part of this whole thing.
Most of these micro ratchets share manufacturers and therefore parts, and you can find the exact same tool from a few brands, or the same head on different tools. The Topeak for example, is the exact same tool sold by Granite and Blue Point, and it is almost the same as the Giant ratchet, and the PK ratchet, which also come under other brands. -
@ReamerPunch said:
The Topeak on the other hand, now that's a ratchet. A bit expensive to get, and I do not want bike-specific tools with it. I haven't seen any set with just the ratchet, bits, and case, and maybe an extension. Well, I actually have, but it was not branded by Topeak.The Lite DX version I posted is the closest I've found, in that the only bicycle-specific tool in the package is a pair of little nylon-plastic tyre levers... which you can easily chuck or give to a cyclist friend at work. It has the bits, ratchet and a 6mm extension, leaving room for a few more extras of your choosing.
UK Amazon has them for about £22, currently. -

I just ordered it. And the Prestacycle one.
The Topeak cannot be missing from this thread I think. Although it is almost identical to my PK Tools ratchet. But the Topeak has a dozen bits, so I'll cannibalize the set once it's here.
The Prestacycle looks great, too. A big longer, a bit more robust, and the extension can fit through the head for the T-handle configuration. And it's not that expensive for what it is. -
Also, I've been looking closely at the Klein one. Adam is using it in the Toolbox Challenge. Small head, 72 teeth, good quality, I like the finger hole too. And this is probably the only one not branded by anyone else. It only comes with four bits and the socket adapter, but that's fine, already have hundreds of bits. ::)

I have decided not to get the Wiha one.
The head is the same as the CyclingDeal Cigar kit ratchet, that I have. More on that when I review it.
But the Wiha does not have an in-line driver, and it is heavier. And I already have that head in another ratchet, so I don't know. It does have a nice case with a ton of good quality bits, so I'll think about it. It might be on sale one day.

-
On the subject of ridiculously small keychain-sized ratchets, I found these guys:
https://www.enjukuracing.com/products/hks-tone-ratchet-key-holder-set.html
https://www.amazon.com/HKS-Tone-Ratchet-Key-Chain/dp/B084S532XDThe first one comes with a quick-release 1/4 drive insert, and has a direction switch.
The second one has no ratchet insert, so you need to buy it separately, no direction switch (use other side to change direction), but does have a cool bonus pivot, and is cheaper...
I was tempted to get the first one because of quick-release and direction switch.If you hook it up to this adapter from 10mm to magnetic hex bit (https://www.amazon.com/GEDORE-7RB-6-Adaptor-Hex-10/dp/B004ISRGIO) instead of using the quick-release insert, you can make it directly accept hex bits instead of chucking on a larger 1/4 drive to hex bit adapter...
These things are ridiculously small and definitely keychain sized (~ 2"), to the point where it might actually impair their functionality as a ratchet. With practice you can make it work. But I guess they are cool fidget toys that can double as a real ratchet in times of need... The 3"-4" long ratchets might be more usable if the goal is real-world use.
Also finger ratchets like these that directly accept bits would maybe make sense for EDC (bonus made in USA): https://www.amazon.com/gp/product/B00DTEDYAM/
-
Interesting thread and great reviews on each.
-
@lsalzman said:
On the subject of ridiculously small keychain-sized ratchets, I found these guys:https://www.enjukuracing.com/products/hks-tone-ratchet-key-holder-set.html
https://www.amazon.com/HKS-Tone-Ratchet-Key-Chain/dp/B084S532XDThe first one comes with a quick-release 1/4 drive insert, and has a direction switch.
The second one has no ratchet insert, so you need to buy it separately, no direction switch (use other side to change direction), but does have a cool bonus pivot, and is cheaper...
I was tempted to get the first one because of quick-release and direction switch.If you hook it up to this adapter from 10mm to magnetic hex bit (https://www.amazon.com/GEDORE-7RB-6-Adaptor-Hex-10/dp/B004ISRGIO) instead of using the quick-release insert, you can make it directly accept hex bits instead of chucking on a larger 1/4 drive to hex bit adapter...
These things are ridiculously small and definitely keychain sized (~ 2"), to the point where it might actually impair their functionality as a ratchet. With practice you can make it work. But I guess they are cool fidget toys that can double as a real ratchet in times of need... The 3"-4" long ratchets might be more usable if the goal is real-world use.
Also finger ratchets like these that directly accept bits would maybe make sense for EDC (bonus made in USA): https://www.amazon.com/gp/product/B00DTEDYAM/
Those are quite neat. True, they could be too tiny to actually use effectively. The Ares is only 85mm, and although heavier, could very easily live on a key-chain.
-
@Tasky said:
^ That's pretty much what I was gonna say about the Topeak.One thing I have found is that the inline driver, the lack of knurling really robs you of grip and power... but a sleeve of Sugru built up flush with the driver end, with some ribs or chequering laid in with a credit card edge, before leaving it to cure overnight, does work rather well!!

I've seen two ratchets that address this quite convincingly.
The Blackburn Big Switch ratchet has knurling on the in-line driver.
Looks like Topeak-sized, but even more expensive. I also have no use for the extra bike stuff, and I haven't seen it available in other sets.

The Synchros Lighter has knurling on the stem. Also a good approach. I do not know which of the two I would like better. Maybe the Blackburn, I think. Kinda curious to try out both. Maybe one day. But the Synchros is way up there. I can get two Topeaks and a Happy Meal for one Synchros.

-
-
@ReamerPunch said:
I've seen two ratchets that address this quite convincingly.
The Blackburn Big Switch ratchet has knurling on the in-line driver.I agree, the Blackburn is likely the better of the two, as the knurled section is thicker. The Synchros is a bit thin on the stem and, having large hands, I built up the stem of my Topeak for the same reason.
-
I'm not sure if this counts, but I use this a LOT at work...
![DhGYzc0[1].jpg](/assets/uploads/_imported_attachments/migrated/529882_DhGYzc0%5B1%5D.jpg)
-
Good work thank you for this thread and those who offered their thoughts. I have loved the idea of a mini ratchet and a while ago I made one to fit my LM bit holder. It was decent but not compact per se. I enjoy seeing everything and while I am not a fan of the pass thru ratchets I am intrigued.
Looking forward to the next installments.
-
-
@ReamerPunch said:
Thanks!
I've got more to post. Waiting for another two to ship any day now. And I am thinking about ordering the two I mentioned above.

Would you accept "help" so you can get the Vic Ratchet?
(I am really curious of how it performs against the others)- I'm sure a big comparison table could be super useful
-
I am open to suggestions.

I am thinking of making a table or two. I'll see if I can get it started today. -
@charlie fox said:
I'm not sure if this counts, but I use this a LOT at work...It sure does!

I've seen that before. And it's not that expensive. I would prefer an in-line driving socket instead of a bottle opener, but it does have several functions. Do you find the bottle-opener notch annoying at all?
-
@Aloha said:
Good work thank you for this thread and those who offered their thoughts. I have loved the idea of a mini ratchet and a while ago I made one to fit my LM bit holder. It was decent but not compact per se. I enjoy seeing everything and while I am not a fan of the pass thru ratchets I am intrigued.Looking forward to the next installments.
Thanks.

I've got a couple on the way, and looking around for more.
I particularly like those with an in-line driver, it is really handy.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login











