EDC Bit Ratchets
-
-
Quick 'n dirty review of the Real Avid X3 driver gunsmithing set :
[attach id=0 msg=2575890]Stored in a fragile plastic case, it is quite compact, until the latch breaks (ask me how I know)
[attach id=1 msg=2575890]
[attach id=2 msg=2575890]
[attach id=3 msg=2575890]Marketed by Real Avid as a gunsmithing set, it features a 1/4" ratchet and extension, and 13 bits oriented towards AR-15 and similar rifle maintenance:
HEX: 5/64", 3/32", 5/32", 3/16", 3.0MM, 4.0MM, 5.0MM
TORX
: T10, T15, T20, T25
PHILLIPS
: #1
FLAT: 5MM



-
[attach id=0 msg=2575891]
[attach id=1 msg=2575891]72 teeths Ratchet with 2 additional 1/4" holes, can be used alone or with the extension that can be either put in the ratchet head or in any of the two additional holes to make a "long screw driver" or a T-handle screw driver
[attach id=2 msg=2575891]
[attach id=3 msg=2575891]As much as I found found the concept interesting, the resulting product is ... "Meh", considering the 45€ I could get it for.
- Tolerances are loose, the extension wobbles when plugged into the ratchet
- Storage case is cool on paper but badly made: any time you close it you must make sure both shells are properly aligned and be careful not to break the latch
- Any other ratchet and bit set can answer the same market niche for a lower price or higher quality, or both: get a Facom, Wera, Usag, or whatever set you like and put the bit set your really need for your activity.




-
-
-
@m47mu74nt said:
As much as I found found the concept interesting, the resulting product is ... "Meh", considering the 45€ I could get it for.- Tolerances are loose, the extension wobbles when plugged into the ratchet
- Storage case is cool on paper but badly made: any time you close it you must make sure both shells are properly aligned and be careful not to break the latch
- Any other ratchet and bit set can answer the same market niche for a lower price or higher quality, or both: get a Facom, Wera, Usag, or whatever set you like and put the bit set your really need for your activity.
That is so unfortunate. It really does look like a premium set. I guess I'll drop it from my "to buy" list. Thanks.

-
It is really unfortunate!
I was looking for some of their nicer/premium toolkits (like the torque limited bit set) but like wine, if the producer can't get to make a good entry level product, it is not advisable to even get their "top tier" product.I used the kit again today, and I may have been a bit harsh on the ratchet/extension as it does it's job correctly, but that plastic case really takes everything down.
-

WorkPro W002147A Mini Bit Ratchet
Weight: 54g
Bit set: 116g
Length: 105mm
Head width: 18mm
Head clearance with standard bit: 27mm (adds 2mm)
Teeth count: 72
Minimum swing arc: 5°
Bit retention: spring detent
In-line driver: no
Bit material: S2 steel
Handle material: Chromium-Vanadium steel
Price: $10 with 20 bits and two bit holders
8mm box wrench
Bits:
Phillips 0, 1, 2, 3
Allen 3, 4, 5, 6
Pozi 1, 2, 3
TamperProof Torx 10, 15, 20, 25, 30
Slotted 4, 5, 6
Square socket adapterAccessories
The WorkPro mini ratchet comes with twenty bits and two rubber bit holders. The bits are made of S2 steel, which is nice to see in such an inexpensive set. They are well-made and fit their respective screws perfectly. The bit selection is great, with Allen, Pozi, even Tamperproof Torx and a square socket adapter, and no repeats. The ratchet is also available with an Imperial bit set.
The bit holders are the common rubber variety, but since this set does not come with a case, the holders are much appreciated.
Dimensions
At 54 grams, this is kind of chunky, but understandable considering the length. At 105mm long, this is definitely on the longer side of edc ratchets. The head is only 18 mm wide, which is great considering the teeth count.
Bottom right: CROM, Vessel 4mm, Sundry, Ares, Wera, Tone, Railer, Blue-Point, WorkPro, VictorinoxTeeth Count
This has 72 teeth, which is on the higher end of the spectrum. It has a 5 degree return angle, so it will be able to work even in very confined spaces.Bit Retention
Bits are held in with a spring. This looks like the common spring of high end edc ratchets, like PrestaCycle, Topeak, etc, but it is not. The spring on the WorkPro is a little longer than it needs to be, so it can slide along the bit socket about 2 mm back and forth. It is also noticeably weaker. Bits are still held in firmly, and stubby bits are easy to remove.Bit compatibility
Thanks to the hole in the head, the ratchet can be used with double-ended bits.
Stubby bits are easy to remove. Leatherman bits work perfectly as well.
Switch action
The switch is small, and tucked behind the knurled wheel. It does seem improbable that it would be bumped accidentally, but it feels a little loose.Ease of use
The WorkPro ratchet has a comfortable four-finger grip, thanks to its length and flat body. With 72 teeth, it can turn fasteners in quite tight spaces.
The knurled thumb wheel makes quick work of somewhat loose fasteners. Although it is not as tight as on other ratchets, the knurled wheel cannot be operated with only a thumb or index finger. Because of the looseness of the ratcheting socket in the frame, it takes pinching it to make it turn, otherwise it is just pushed against one side of the frame and does not move.
The 8mm box wrench is useful for both Metric and Imperial fasteners, and can be used as a loop for attaching a cord to prevent loss.
The hole in the head allows for double-ended bits. It only adds a couple of mm to a bit's clearance.
Construction Quality
This may seem like another version of the high quality ratchets we have seen so far, like the PrestaCycle, BluckBurn, Topeak, etc. It is not. The switch has a lower detent, and the bit retention spring is weaker and a little ill-fitting on the bit socket. The ratchet mechanism has some play in the frame. This is a first so far. Many ratchets exhibit some wobble of the ratchet mechanism in the frame, but this feels a little loose. It still works properly and has not failed in the slightest, but the wobble does not inspire confidence, especially considering that it is absent in similar ratchets, and is much worse than even the most inexpensive ratchets reviewed so far.The finish is consistent and crisp, and the bits are flawless.
Portability
Thanks to the 8mm box wrench end, the ratchet can be attached to other gear with large carabiners or cord. It will not fit in an Altoids tin but it will in edc pouches, or multi-tool sheath side-sleeves.
Value
Seeing how it only costs $10, it does seem like a good deal. It comes with 20 bits, two bit holders, and has some nice features.Conclusion
On paper, the WorkPro mini ratchet seemed too good to be true and well, it is. The price is quite low, among the lowest so far. The features are there: 72 teeth, knurled thumb wheel, hole in the head, 8 mm box wrench, good ergonomics. It also comes with two bit holders and twenty flawless S2 bits, with a good bit selection and no bit repeats.
However, the quality feels a little lacking. The ratcheting socket, the bit retention spring, and the switch are all a little loose in the frame. Had corners been cut elsewhere, like bit amount, bit material, teeth count, this would have been an excellent choice for an inexpensive bit ratchet. Again, it has not failed in any way so far, and it may continue working perfectly and even outlast many ratchets of this thread. Let's just say that if it does fail in the near future, it will not be surprising. Is it recommended? Tough to say. It is very inexpensive, and for $10, it would be worth it just for the bits and bit holders.
Pros
-Very inexpensive.
-72 teeth, knurled wheel, hole in the head, 8mm box wrench.
-Excellent bit selection, with Allen, Tamperproof Torx, etc, and no repeats.
-Set comes in both Metric and Imperial.
-Good ergonomics.Cons
-Lower quality compared to similar ratchets. -
-

Blue-Point BLPKSB004 Ratchet Set
(The ratchet can also be found branded by Granite, KS Tools, PowerTorque, Topeak.
Same size and basic design as Budnitz, Fortis, Katana, Rujoi, Signet, Sonic, and Smato)Warranty: Lifetime
Max torque rating: 30 Nm / 22 ft lb
Weight: 29g
Set weight: 166g
Length: 93mm
Head width: 15mm
Head clearance with standard bit: 25.5mm (adds 0.5mm)
Teeth count: 52
Minimum swing arc: 7°
Bit retention: spring
In-line driver retention: magnet
Bit material: Chromium-Vanadium steel
Handle material: Chromium-Vanadium steel
Price: $33* with 20 bits and case
(price is average; no new stock exists; set is discontinued)
Bits:
Phillips: #1 x2, #2 x2,
Slotted: #4 x2, #5 x2, #6 x2
Pozidriv: #1 x2, #2 x2, #3 x2
Tamperproof Torx: 10/15/20/25Accessories
The Blue-Point BLPKSB004 Ratchet comes with 20 bits and a case.
The bits are made of Chromium-Vanadium steel, and are highly polished.
The case is made of hard plastic, with proper hinges and a long, steel hinge pin. It is lined with foam and the bits and ratchet stay in by friction. The lid has a sticker with bit designations.Other than branding, the ratchet is identical to the Topeak and Granite ratchets, reviewed in this thread previously.
Note that there are multiple versions of the BLPKSB004 Ratchet Set, all with different bit selections.

Dimensions
The Blue-Point ratchet is the same exact ratchet as the Topeak Ratchet Rocket and Granite Rock'n'Roll ratchet. 15mm wide head, 52 teeth, 93mm long, 29 grams heavy. Quite unobtrusive.
Bottom right: CROM, Vessel 4mm, Sundry, Ares, Wera, Tone, Railer, Blue-Point, WorkPro, VictorinoxTeeth Count
52 teeth for a 7 degree minimum swing. Quite good for a 15mm wide head.Bit Retention
Same spring as the Topeak, Wera, Klein, etc. Retention is excellent.
The inline driver magnet is quite strong, so stubby bits with thin tips may require pliers to be removed.
The bits the ratchet comes with are so highly polished, that some are also quite hard to remove with just fingers.Bit compatibility
Thanks to the hole in the head, the Blue-Point ratchet can use standard double-ended bits, Steinwhale stubby double-ended bits, and Leatherman bits. Regular and stubby bits have no issues.
Steinwhale stubby double-ended bits fit perfectly in the inline driver.
The inline driver cannot use standard double ended bits as they are too long to engage and be used.
Switch action
The action switch is small and has excellent detent. It does not wobble at all, it does not protrude enough to get caught on anything, and it will not be bumped accidentally, reversing the action.
The switch can be operated by just a fingertip, but a fingernail may be necessary, as the detent is quite strong and the switch itself quite small for it to be operated just by skin.Ease of use
The switch can be operated quite easily with a fingernail; maybe not so easily with just a fingertip.
Stubby bits cannot be removed from the in-line driver easily.
Standard bits can be removed extremely easily, despite the ratchet having a strong spring.
The included bits are quite highly polished, which makes them a little slippery.The tool is small, with an extremely narrow head, and excellent head clearance with a bit inserted. The tool is still long enough and strong enough to perform edc tasks.
The in-line driver is a much appreciated feature and works well. It would have been even better if the stem of the driver had some knurling, to provide traction.
The high teeth count and knurled finger wheel make things quick.
Both bit driver sockets are funneled to make bit insertion easier.
The spring keeps the bits in place, and also holds the ratchet mechanism in the head, so this can be disassembled if needed.
Construction Quality
The included bits are quite highly polished, which helps with corrosion. They are finished flawlessly, as is the ratchet, which makes sense, as it is the identical ratchet branded by Granite and Topeak.Portability
At 29 grams and 93mm long, the Blue-Point is on the small side of mini ratchets. It can sit comfortably in all sorts of pouches, pockets, pen sleeves, even tethered on gear with a clip through the hole in the head.
At 166 grams, the set is still rather lightweight, considering it has 20 bits.The case is quite compact, but admittedly not the perfect size or shape for edc. The wallets similar ratchets come in, like Topeak, Granite, Blackburn, are all arguably better choices for edc. Still, there is nothing wrong with the Blue-Point case. It closes securely, it holds everything quite convincingly, and there is plenty of space for an extension and a few more bits and bobs.

Value
Being long discontinued complicates its value for money. It certainly is a nice set, with a high quality ratchet, 20 bits, a case, and arguably most importantly, lifetime warranty. All these will of course mean nothing if you cannot find it anywhere, but it does become available on various auction sites etc, although the price may fluctuate quite a lot.
Conclusion
It is no surprise that the Blue-Point BLPKSB004 Ratchet Set may seem familiar. It shares its ratchet with Topeak and Granite sets: same high quality, compact size, and features, different bit selection and case. If this proves too difficult to track down, and you are set on getting it, then a Granite, Topeak, Smato, Signet, Katana, etc set will offer a very similar experience, and you will probably save yourself some money.It is still recommended, of course. It would not make much sense not to. This is an excellent little ratchet with many nice features, it comes with 20 bits and a case, and it has lifetime warranty. Though discontinued, it still shows up every now and then, and although it may be overpriced, you could get lucky and find a bargain.

Pros
-Lifetime warranty.
-Same dimensions, features, high quality, portability as Topeak ratchet.
-Multiple set versions.Cons
-Hard to find.If you liked this ratchet, also check out:
-
Just in!

Hazet 2300SH-1
RockBros mini ratchet set
-
So, quick update. **The RockBros is going back. Do not buy it. **
The ratcheting mechanism does not work properly. When set to tighten, it occasionally jams up and has to be jiggled free, only to bind up again.
When set to loosen, it is almost permanently jammed, and does not work at all. -
Well that sucks
-

RockBros TG-T8008 mini ratchet set
Weight: 32g
Set weight: 158g
Length: 95mm
Head width: 20mm
Head clearance with standard bit: 33mm (adds 8mm)
Teeth count: 72
Minimum swing arc: 5° (in theory)
Bit retention: magnet
Extension retention: magnet
In-line driver retention: magnet
Bit material: S2 steel
Handle material: Aluminium alloy
Price: $20 with 12 bits, extension, case, and drawstring pouch
Bits:
Phillips 1, 2
Allen 2.5, 3, 4, 5, 6
Torx 15, 20, 25, 30
Slotted 4Accessories
The RockBros TG-T8008 set consists of ratchet, extension, 12 bits, a holder, and a drawstring pouch.
The bits are made of S2 steel and are highly polished. The extension is listed as aluminium alloy and has a magnet. The pouch is single-stitched and has two draw-strings.The holder is plastic. The ratchet attaches to the side, in a spot contoured for the ratchet's shape. The ratchet is flat, as opposed to the usual cylindrical body of most ratchets in this thread. The flat body allows the ratchet to enter its spot sideways, then twisting it 90 degrees makes it fit perfectly in there. The extension is stored while attached to the ratcheting end, so the lid that closes to secure everything captures the extension, preventing it and by extension the ratchet, from twisting. When closed, there is enough room in the lid for the ratchet to rattle left and right, but everything does seem to stay in the holder securely. Keep in mind that because the ratchet stays in the holder by shape, but not by friction/magnet/yokes, so if the lid is open, simply shaking the holder can make the ratchet fall out.
The bits are held in two bit holders. Each bit is held in place with an individual neodymium magnet. These bit holders pivot out and can also twist around, although this seems to have little use. They do seem to be removable. There is a big hole in one corner that will fit large carabiners or cord for a lanyard, and there is a smaller hole on the bottom for a thinner lanyard or split-ring as well.

Dimensions
At 95mm, this is a little longer than average. Thanks to the Aluminium alloy, at 32 grams, it is quite lightweight for its length and width.
The ratcheting end adds 8mm to a bit's clearance, which is a bit higher than average.
The head is 20mm wide, which for 72 teeth would be fine, but it is not.
Bottom right: 711L, Ares, Tone, Hazet 863MB, Engineer, PK Tool, RockBros, Neiko, VictorinoxTeeth Count
With 72 teeth, this, theoretically, has a minimum arc swing of 5 degrees. In reality, it has 20 degrees of slop before engaging the next tooth. This is the worst slop we have seen so far, and it almost rivals ratchets that have only 16 teeth.Bit Retention
Bits are held in the ratchet, inline driver, and extension with magnets.Bit compatibility
The ratcheting end and inline driver are extremely shallow for double-ended bits.
The extension is deep enough for Steinwhale stubby double-ended bits.
Switch action
The switch is loose, sloppy, and switches the action between tightening and locked. More on that below.Ease of use
More like "Difficulty of use" to be honest. Using this would have been straightforward: knurled wheel for quickly turning fasteners, 72 teeth for 5 degrees of minimum arc swing, inline driver.Unfortunately, using this ranges from average to impossible. The ratchet is sloppy, loosening does not work, the inline driver is bad, and the ratchet adds 8mm to a bit's clearance.

Bottom left: the ratchet is set to tighten. It is able to hold up weight, since it is set to turn anticlockwise.
Bottom right: it is set to loosen. It should not be able to hold any weight. It should have collapsed instantly. But it is bound.Construction Quality
Construction quality is not good. This is probably the worst ratchet we have seen so far in this thread, and the only ratchet I have received, reviewed, and will send back.The ratcheting mechanism does not work. When set to tighten, the ratchet binds up occasionally and will unbind with a little jiggling only to jam again after a few teeth.
When set to loosen, the ratchet is almost locked. It will only work if the switch is kept to the right and down with my thumb, which is less than ideal, and even then, the action is very crunchy, crude, and rough.As mentioned previously, the ratchet should have 5 degrees of minimum arc swing, but there is a 20 degree slop before the ratchet engages the next tooth.
The inline driver is made crudely. Bits do not sink in completely, and therefore do not engage the magnet properly. Also when pulling out bits, metallic flakes are sometimes stuck on them.
The knurled finger wheel is barely knurled. It requires a firm pinch to spin it.
The ratchet has an almost mirror finish, but it covered in scratches and dents.
The holder lid pivot pin protrudes from one side and can snag on fabric or skin.

The ratchet is set to loosen. It should not be able to hold any weight.Portability
The holder is a little bulkier than it could be. Still flat enough for a pocket.
The ratchet weighs only 32g, so it would have been a nice, lightweight option.
Value
There is no value to speak of when the ratchet does not work as a ratchet. Do not buy this.Conclusion
Well, here we are. It was only a matter of time to receive a ratchet that did not work out of the box.
There are a few points that I wanted to make.
The holder could be a little smaller. There is a 5mm gap between the bits' tips and the frame. This serves no purpose. The bit holders pivot out to make the bits accessible. There is also a gap between the extension's tip and the frame.
The holder is also way over-engineered. There are many moving parts, that just add steps to using the tool. It also seems that were it to be dropped from any height, it would just disassemble into a plastic mess.
The high polish of the ratchet makes it a little slippery and it collects fingerprints like no tomorrow.
The ratcheting end protrudes a little from the frame so it will not sit perfectly flat in a pouch.
Having a magnet for the ratcheting end makes it add 8mm to a bit's clearance, and with no hole in the head, it cannot use double-ended bits.
At 32g, this is quite lightweight for its size. It would have been a nice, lightweight option that is still long enough for a comfortable grip and some torque, although the Aluminium alloy is certainly inherently weaker than Chromium-Vanadium.Alas, all those points are pointless. The ratchet does not work as a ratchet. That negates any positives it may have had. Even the worst ratchets before this worked as ratchets, which was supposed to be a given, but apparently not. Do not buy this.

Pros
-Able to be refunded.Cons
-Ratcheting mechanism does not work when set to loosen.
-Ratcheting mechanism binds constantly when set to tighten.
-20° of slop before engaging next tooth.
-Holder is much bulkier than it could be.If you liked this ratchet-shaped object, you probably skipped the text. Check these instead:

-
Writing the Hazet 2300SH-1 review, and what do you know. Licensed by Wera. Nice.



-
Writing the Hazet 2300SH-1 review, so I got out the Wera Tool Check Plus 1 to compare things, and this happened. Let's see what Wera's warranty is like.
The Tool Check Plus 1 was delivered to me on 12-Oct-2025. I've had it for about 10 months, and the bit driver has been removed and put back maybe twenty times so far.


-
Second RockBros. Same issue. Do not buy this.

-
-
@ReamerPunch said:
Writing the Hazet 2300SH-1 review, so I got out the Wera Tool Check Plus 1 to compare things, and this happened. Let's see what Wera's warranty is like.The Tool Check Plus 1 was delivered to me on 12-Oct-2025. I've had it for about 10 months, and the bit driver has been removed and put back maybe twenty times so far.
Got a reply from Wera Customer Service. They said that for the first year after purchase, the seller can warranty the item. But they did offer to replace the part. It has been ten months since I got it from Amazon AU, them being the actual seller, so I will have Amazon replace it, since I still can. Should be here tomorrow.
-

Kakuri Sangyo Sundry SDR-B02 mini ratchet set
(Sundry is a product line of the Kakuri Sangyo brand.
The ratchet can also be found branded by Ares, SabreCut, Sealey)Max torque rating: 58 Nm / 43 ft lb
Weight: 58g
Bit set: 46g
Socket set: 60g
Set weight: 164g
Length: 85mm
Head width: 21mm
Head clearance with standard bit: 25mm (adds no length)
Teeth count: 72
Minimum swing arc: 5°
Bit retention: Ball detent
In-line driver retention: Ball detent
Bit material: S2 steel
Handle material: Chromium-Vanadium steel
Ratchet gear material: Chromium-Molybdenum steel
Price: $14 with 8 bits and 6 sockets
Bits: Phillips 1, 2, Flat 4, 6, Allen 4, 5, 6, Square Socket adapter
Sockets: 4, 5, 5.5, 6, 8, 10Accessories
The Sundry mini ratchet comes with seven standard bits, a socket adapter, and six sockets.
The bits are stored in a plastic, modular bit holder that consists of three pieces. This allows users to carry three, five, six, or eight bits, depending on configuration. It has a loop that allows more bit holder pieces to be added, or can be used to attach the bit holder to something with a carabiner or clip.
The sockets are stored in a plastic rail and are held by friction. It has a hole that fits small split-rings, so it can also be attached to a carabiner.
Dimensions
The Sundry is the exact same ratchet as the Ares, except painted black. It is short, at 85mm. It has a stocky, robust body, with a somewhat wide head. The Sundry adds no length to the inserted bit.
Bottom right: CROM, Vessel 4mm, Sundry, Ares, Wera, Tone, Railer, Blue-Point, WorkPro, VictorinoxTeeth Count
The Sundry has a very high teeth count, at 72, which gives a very low swing arc, at 5 degrees. This is just excellent for an inexpensive ratchet like this.Bit Retention
The Sundry has ball detents for both slots. This allows the bits to be removed easily, even stubby bits. For a little more retention, have the ball detent rest on the marked side of bits, for more traction.Bit compatibility
Stubby bits can be removed very easily. Standard double-ended bits and Leatherman proprietary bits will fit the ratchet end, if one end is slim enough to clear the hole. They do not work in the in-line driving socket, as it is too shallow for them to engage and turn properly.
Impact bits and extensions work beautifully in both ends, as the ball detents are at the perfect height to hold them in place.
Switch action
The Sundry has a sliding switch. This has better detent than the Ares. It does not move accidentally. As it is a slider, it sits flush against the body and does not catch on anything. It is knurled in two opposite directions, to make it easy to operate.Ease of use
The Sundry has an in-line bit driver slot, and both slots have ball detents, making it easy to swap bits. The weight is not enough to cause concern. When using the in-line driver slot, the neck flanges provide enough traction for the tool to turn even stubborn screws. The high teeth count allows for very little swing to turn a bit, so even with almost no space to move the tool, it will still turn fasteners. The ratcheting end also adds no length to a bit, allowing for very low clearance, especially paired with stubby bits.
It does not have a knurled finger wheel. The in-line bit socket is not funnelled, which is unusual, although bits are still easy to insert.
Construction Quality
The Sundry is decently finished. The slider's channel and neck flange channels may look just a tiny bit unpolished, but the black paint does a good job of masking any imperfections. The paint itself has held up nicely. The ratcheting action is smooth and consistent. The bits fit the slots well with little wobble. The ball detents work as they should, providing adequate retention.Portability
The Sundry may seem heavy, but it is also very short. If it comes down to length but not weight, it will do well. With wide ends and a thin body, it fits well in edc pouches and multi-tool case side-sleeves, even pen sleeves. The ratcheting head has a hole, which allows the tool to be clipped to a pack or key-chain with a quick release clip or carabiner.
The bit holder and socket rail can be attached to a clip.
Value
At $14, it is already a good value for money, considering its pros and that it comes with eight bits and six sockets. But it gets even better, when compared to the Ares mini ratchet set.Conclusion
The exact same ratchet as the Ares, the Sundry has high teeth count, high bit compatibility, an in-line driver, and adds no length to a bit's clearance. It also comes with six sockets, and eight S2 steel bits, compared to the eight Chromium-Vanadium the Ares comes with. It also is less expensive than the Ares.This is truly an amazing deal, considering the accessories and all that the ratchet has to offer. It may be an elusive deal, though, as the set is not readily available. It does appear in Amazon Japan and Amazon AU, so not impossible to find.
The Ares ratchet has remained a staple in the recommendations of this thread, and the Sundry is no different. If you happen upon it, and the price has not changed much, this is a capable little set and excellent value for money.

Pros
-Heavy duty.
-Flanged neck for easier in-line driving.
-High teeth count.
-Ratcheting end adds no length to inserted bit.
-Good but not overly strong bit retention.
-Ratchet end compatible with many double-ended bits.
-Better value than the Ares ratchet set.Cons
-Not readily available.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login














































