EDC Bit Ratchets
-

LaBear mini ratchet
Weight: 44g
Length: 99mm
Head width: 19mm
Head clearance with standard bit: 30mm (adds 5mm)
Teeth count: 12
Minimum swing arc: 30°
Bit retention: magnet
In-line driver: no
Bit material: S2 steel
Handle material: Chromium-Vanadium steel
Price: $9 with 10 bits (listed as 11 but PH1 missing)
Bits: Phillips 2, Slotted 4 and 6, Torx 15 and 20, Allen 3, 4, 5, 6, 1/4" square adapter (and Phillips #1 bit listed but missing)Accessories
The LaBear comes with nine stubby bits (listing says ten but one bit was missing) and a 1/4" square adapter in a bit holder. The bits are very difficult to remove from the holder.Also included is a plastic finger spinner that attaches to the ratcheting bit socket. The spinner's opening is quite a tight fit for bits, and it obstructs view of the bit socket, so it is not possible to align the bit properly and insert it. To change a bit, the bit has to be removed, then the spinner has to be removed, then a new bit is inserted, then the spinner again. Quite a lengthy process if working with multiple drivers.
The spinner is 20mm wide, so adding this to the ratchet increases the head width.
Dimensions
The LaBear ultra low-profile ratchet seems to be misnamed. With no bit inserted the head is 15mm tall. The ratchet adds 5mm to a bit's clearance.
The head is 19mm wide, not the widest, not the narrowest.
It is 99mm long, which is respectable, and means the LaBear will fit comfortably in any garbage bin.
Teeth Count
The teeth count is abysmal, at only twelve, which means that this has a minimum swing arc of thirty degrees. It does not get worse than this.Bit Retention
The bits are held in place by a magnet. It is very strong, making bits with thin tips hard to extract.Bit compatibility
Double-ended bits cannot be used in this. Stubby bits with thin tips are hard to remove.
Switch action
The LaBear ratchet has an oversized spring-loaded pawl which acts as its own switch. It has very poor detent and switches sides with the slightest touch.Ease of use
Even though it is advertised as an ultra low profile ratchet, this has quite a tall head. The bit socket protrudes quite significantly. The head adds 5mm to an inserted bit's clearance, which is barely low profile, let alone ultra low profile.
The ratchet has only twelve teeth, so it will need more space than any other ratchet to be able to engage the next tooth and turn a fastener.
A finger spinner is included, which helps with somewhat loose fasteners. This attaches to the driving socket quite firmly, and also increases the bit retention. It also makes it hard to remove bits, and time-consuming to change bits around, as the spinner has to be removed and re-inserted along with the bits.
The action can be reversed accidentally, due to the pawl's poor detent.The exposed magnet adds some versatility. The tool can attach to ferrous surfaces, and also act as a short magnetic pick-up tool.
The bits are difficult to remove from the bit holder. Some bits are very tight, and others require additional tools to aid extraction.

Construction Quality
The magnet was barely pressed in the socket. The product listing shows the magnet being flush with the back-plate.
The two halves of the frame leave gaps, as they are misaligned and do not sit flush against each other. There are burrs and imperfections along the edges.
The rivets are not properly chamfered and will grab fabric.
The ratcheting mechanism feels weak. The gear turns very easily, with very little resistance. The ratcheting clicks are anemic. The whole mechanism feels loose and janky.Portability
The ratchet has a flat frame and is not overly wide. It fits in multi-tool pouch side-sleeves and edc pouches. The (extremely) exposed magnet allows the tool to be stored on a ferrous surface. Of course it will take very little space in any recycling bin or garbage can, and is heavy enough to be tossed into a lake or river.
Value
At only $9, this is the least expensive ratchet so far. No surprises there. It is quite obvious that several corners were cut to achieve this.Conclusion
This costs only $9 and it shows. The ratchet is functional, although that is a given. The bit set would arguably be worth the asking price. The bits are S2 steel, and there is also a 1/4" square adapter included. Alas, a bit was missing, and this seems to be the norm with this ratchet.The ratchet has the fewer teeth so far, at a mere dozen. It also has a decisively not ultra low profile head. The action is weak, and can be reversed easily by accident. As if these were not enough, the ratchet is riddled with flaws. The magnet was barely pressed in. The frame has gaps and imperfections. The rivets are rough and will catch on skin and fabric.
This is a new low. There is no way around this and no reason to recommend it. There are much better options for a few dollars more.
Pros
-Exposed magnet adds versatility.
-S2 stubby bits.Cons
-Arriving with missing bit is common occurrence.
-Only 12 teeth.
-Head is 15mm tall with no bit.
-Head adds 5mm to bit clearance.
-Poor build quality.
-Bits are extremely tight in holder.
-Spinner increases head width and makes changing bits tiresome.If you liked this ratchet, read this review again and pay attention this time. Also check out:
-
I used a Knipex pliers wrench to press the LaBear's magnet in the socket. :D
Before:

After:

-
@m47mu74nt said:
Looks like 8€ Lidl one is far better than that one!
(Btw, I've just ordered Facom R1-pico in the yellow cycling limited edition variant, just because it was yellow and ... A limited edition.
)I'd take the Lidl one over the LBear any day of the week.
And that yellow box looks great. That's a fantastic shade of yellow.

-
Lots of great in depth reviewing, RP :o :ahhh

-
Thanks!

-
I keep seeing tools in Amazon that are out of stock...

Something's up. :ahhh -
-

Vessel low-profile ratchet
(can also be found branded by Broppe and Lattook)
Weight with no bits: 48g
Weight with 2 bits: 54g
Length: 104mm
Head width: 16mm
Head clearance with standard bit: 25mm (adds 0mm)
Teeth count: 16
Minimum swing arc: 22.5°
Bit retention: spring
In-line driver: no
Bit material: Chromium-Vanadium steel
Handle material: Chromium-Vanadium steel
Price: $16 with 11 stubby bits
Bits: Allen 2/3/4/5/6, Phillips 1, 2 x2, 3, Slotted 4 and 6Accessories
The Vessel low-profile ratchet comes with eleven stubby bits and a bit holder. The bits are the shortest stubby bits yet, at only 18mm long (the SK ratchet comes with three half-cut bits, that are 12mm long).
The bit holder is modular. It consists of three connecting pieces. When connected, the pieces have an insignificant amount of wobble and stay together with no issues.
Bottom right, left to right: SK ultra stubby (12mm long), Vessel stubby (18mm long), SK Anex Klein stubbies (19mm long), LaBear Mulwark (20mm long)Dimensions
The Vessel ratchet is 104mm long, which is a little above average. The head is 16mm wide, which is great. The head adds no length to a bit's clearance.
At 54g with two bits in the handle, it is about average weight, perfectly acceptable.
Teeth Count
With only 16 teeth, this requires some space in order to engage the next tooth and turn a fastener.Bit Retention
Bits are held in by a spring. This is not excessively tight and offers good retention.Bit compatibility
Stubby bits can be removed easily.
Double-ended bits work well in this thanks to the hole in the back of the head.
Switch action
The Vessel has a spring-loaded, oversized pawl, which is its own switch. The pawl protrudes from both sides of the frame at all times. To reverse the action, a tip must be pushed up or down. It has good detent and it is not easy to get it to reverse accidentally.Ease of use
The Vessel is the only ratchet so far to feature on-board bit storage. It has two bit slots built into the frame. The bits are secured by two rows of ridges in the hard plastic insert. The bits clip into their spots and are very secure. To remove a bit, simply push it out from the other side. The Vessel stubby bits are 18mm long, but the ratchet can store 19mm long stubby bits. 20mm long stubby bits will not fit, and of course, standard bits will not fit in this.
The ratchet gear is oversized and the teeth are exposed, so this can be used as a knurled finger wheel to quickly turn loose fasteners.
The ratchet head is 10mm tall and adds no length to an inserted bit's clearance. As long as there is room to swing this, it will reach into some crammed spots.
The sides have some jimping that provides some additional traction. The ratchet is long enough for a four-finger grip. Reversing the action is very easy.
Top right from left to right: LaBear, Anex, Vessel, Mulwark, SKConstruction Quality
The finish is crisp and consistent. The pawl and gear engage smoothly. Tolerances are great. There are no gaps between the plates and hard plastic insert. The lanyard hole edges are chamfered and will not wear down cords. The rivets are smooth and will not grab fabric. The Vessel logo is etched flawlessly on the frame. The bits fit in the frame perfectly, clipping in place with an audible click. The ratchet mechanism has very little wobble in the frame.
The sides of the plates appear slightly unfinished, but they are very smooth to the touch.The bit holder is wonderful, with no molding imperfections. The pieces connect to each other convincingly, with very little wobble. Bits are held firmly, but are not overly tight.
Portability
The Vessel ratchet is straight and flat, and sits comfortably in multi-tool pouch side-sleeves, edc pouches, and pen sleeves.
It also has a 4mm lanyard hole, and the bit holder has a loop too, so these can be carried with carabiners or clips, and attached to other gear.
Value
The Vessel ratchet cost $16, and came with eleven stubby bits and a bit holder. The ratchet has some nice features, the bits are 18mm long, and the bit holder is modular.Conclusion
Having 16 teeth is a little low. This will need some space to swing around in order to work. This is a common occurrence with ratchets of the sandwich design. Still, the Vessel has some tricks up its sleeve.Compared to its kin, the Vessel has quite a few features. Jimping for traction, a knurled finger wheel, a lanyard hole, and of course, on-board bit storage. It is also flat, adds no length to the bit clearance, and comes with a modular bit holder and eleven 18mm long bits. It certainly has a lot to offer.
Its features translate well into edc. The ratchet fits nicely in pouches, it has a lanyard hole so it can be tethered or clipped on other gear. The bit holder also has a loop and has a few carry options, depending on the number of bits users want to carry. The ratchet can store two bits within its frame, and it is compatible with double-ended bits as well. The hard plastic insert is a vibrant, highly visible orange, and it even has some jimping for traction. The Vessel low profile ratchet is a solid choice for a compact, edc bit ratchet.
Pros
-Knurled finger wheel.
-On-board bit storage.
-Ratchet adds no length to bit clearance.
-Modular bit holder.
-Shortest stubby bits yet (18mm long).Cons
-Only 16 teeth.
-The ratchet cannot store standard bits.If you liked this ratchet, also check out:
-
Great review RP, I was actually looking at a few of those yesterday.
-
I just got the FACOM R1PICO-NOR in the mail today.
I won't make a dedicated review of it as it the ratchet is basically the RUJOI that RP already reviewed.
all I can say is : it's not worth twice the RUJOI if you don't have use of the box (that is of good quality, much more compact and really well engineered).
(above is the R1PICOPB)I got this one for about 85€ including tax and shipping (it was like 50£, but UK being no more part of EU, taxes are not forgotten
).
the set is based on the FACOM R.180A:

Official product description of the ratchet :
- The compact head allows access to difficult areas when us ing bits 6-point 1/4".
Flexible head 180 °.
The button to lock the head in position. 13 locking positions
60 teeth mechanism for a recover y to 6°.
Reversing lever: easy even gloved hand. Allows visualisation of the direction of rotation.Use with square sockets 1/4 “through ECR.1 ada pter.
Comes with a through ma gnetic extension 100 mm for use “T-handle” (EF.R180). Weight: pawl 70 g, 40 g extension.*
Por whose who are interested, here are descriptions and part numbers of the content :
-
1 x 1/4" ultra-compact flexible ratchet: R.180A.
-
5 x 1/4" metric 6-point sockets: R. 6 - 8 - 10 - 12 - 13 mm.
-
1 x extension: L 100 mm (EF.R180).
-
15 x bits - 1/4" drive bit - 6.35 mm - L 25 mm:
- EP.1T for Philips® head screws: PH1 (EP.101T)- PH2 (EP.102T).
- ES.1T for slotted head screws: 3 (ES.133) - 6.5 (ES.136,5) mm.
- EH.1 for metric 6-point hollow head screws: 2 - 2.5 - 3 - 4 - 5 - 6 mm (real part number is build like this : EH.102,4 for the 2.5 mm bit and EH.106 for the 6 mm bit).
- EXR.1 for vis Resistorx® screws: TT10 - TT15 - TT20 - TT25 - TT30 (EXR.110 to EXR.130).
-
1 x socket holder bit: ECR.1.
-
1 x BV.RPE2 yellow box, the bit holder is actually made of a semi-rubberized injected plastic that won't come out: It comes through the main frame and works both as box shell and bit holder
main difference between the "Special Cyclist Edition" and the R1PICOPB:
- in PICOPB that is not in PICO-NOR:
- ED.1T for Pozidriv® head screws: PZ2.
- ES.1T for slotted head screws: 4.5 - 8 mm.
- PICO-NOR that is not in PICOPB:
- ES.1T for slotted head screws: 3 mm.
- EH.1 for metric 6-point hollow head screws: 2 - 2.5 mm.
NB: The box has a very nice shade of yellow.
NB2: The box alone makes it a good alternative to the RUJOI if you can afford it.
NB3: I wouldn't be surprised to find other Stanley-Black&Decker's brand that would be exactly the same as the FACOM R1PICO, but I couldn't find any yet..jpg)
.jpg)
.jpg)
.jpg)
- The compact head allows access to difficult areas when us ing bits 6-point 1/4".
-
Apparently, FACOM ratchet and extension alone, without box or bit/sockets can be found for 40€, about the price of the whole RUJOI set.
I'll try to find a RUJOI ratchet and extension, to make an indepth head to head comparison. -
@m47mu74nt said:
I'll try to find a RUJOI ratchet and extension, to make an indepth head to head comparison.A very similar ratchet can be found under the KS Tools brand, either stand-alone or in several sets reminiscent of the Facom.
-
@ComboTool said:
A very similar ratchet can be found under the KS Tools brand, either stand-alone or in several sets reminiscent of the Facom.You are absolutely right : it is even cheaper than the RUJOI (25€ on amazon)
Bits visually seem of much lower quality thoughPS: I ordered one so I can make the comparison.
-
As expected with a bit of research,
Another Stanley black&decker brand does sell the same tools as you can find FACOM branded : USAG (Italian brand apparently): 606 1/4 SK, can be found for 50€ on Amazon. (If you don't need sockets, it looks like a much better deal). -
@m47mu74nt said:
You are absolutely right : it is even cheaper than the RUJOI (25€ on amazon)
Bits visually seem of much lower quality thoughPS: I ordered one so I can make the comparison.
Ok, got it today : the KSTOOLS kit is of MUCH MUCH lower quality.
-
The ratchet looks similar, even a few mm longer than the FACOM
-
The extension/T-handle is almost identical
-
The box feels cheap, the bit holder part is of added material and not as grippy (and it's black, not read as on the box pic)
-
The ratchet mechanism isn't as clicky, the hinge isn't as smooth and presents some visual defects
Is is cheaper, and... it is cheaper, should be okay for most work though

.jpg)
.jpg)
.jpg)

-
-
The handle is a little longer on the KSTOOLS, but the heads are visually almost identical, so are the T-handles.
There's a nice feature on the FACOM that is missing on the KSTOOLS : the socket adapter is much shorter.Overall, after that comparison, I feel the FACOM is still too expensive, but it looks like it is still far better than the 25€ KSTOOLS product

.jpg)
.jpg)
.jpg)
.jpg)
-
More great Ratchet sets and pics, RP and m47

-
Thank you!

My reviews are not as in-depth as RP ones, but don't tempt me too much or I'll get some USAG to compare with the two others
-
Awesome review!
But my question is, what do you guys recommend to fit this:
[attach id=0 msg=2361608]
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
















































