Scale swap
-
Do I have to prepare the scales somehow? The Celidor gets only whit a lot force over the washers..
Would a bit heat work? -
I put the cellidor scales in hot water for a minute or so before I press them into place with C-clamps. If you use a vise or C-clamps you must pad the scales with thick cardboard or something to prevent marking. Don't use boiling water. That is too hot. Just about as hot as coffee out of the pot maybe. Try to put the pressure over the pin locations. You can crack them if you press over the wrong spots. Best wishes. G
;) -
I agree. π
-
Done, was actually quite hard work : maybe they where still too cold as they where laying in our post box outside..
I did made sure the pins where clean, put them on, took some paper towel and first did press them together by hand, i think the cellidor where much more stiff than the abs scales..
I did watch a video where someone did press them finally together by standing on the SAK (secure packaged in papertowell), this did the trick for me..



-
Looks good! I ended up using a vice with a rag protecting the scales so as not to damage them. Then I slowly squeezed them together till I could either hear them press in, or I'd remove it from the vice to check.
-
The blue cellidor of my day lie driver Cybertool looks a bit like there are lots of finger marks on it.. maybe I have to polish it a bit.. or itβs the light..
I will take a better picture of it when I got better light
-
If you decided to stand on the SAK to press on the scales, there is a big chance that you might bend a liner. That is definitely something you don't want. A vise, or clamps are a lot safer. Best wishes. G
:) -
Well I think it had survived it, I took a better picture of my daily (bit) driver

-
Looks good to me. Our friend MacGyver uses auto headlight polish to take care of tiny surface scratches. I used to have some Flitz, but used it all up. Since you carry your SAKs, it is inevitable that they will pick up tiny scratches. A few minutes now and then with some polish will keep them looking factory new. It seems that cellidor just picks up scratches and fingerprints and dirt so easily. Best wishes. Gary

-
My huntsman will get the same scales, but it should be much more easy to put them on as the knife is much thinner..
also it will get color fitting tweezers and thoothpick and these korkscrew tools where I still have to decide which one I will use..Might also be there where too cold back then , I had some issue..
-
You do know that if you take the scales off several times, that eventually they will be loose? First time generally works okay. After that they start getting a rattle when you touch them. Eventually you will have to glue them if you want them tight. I generally leave them where they are, unless they are broken. Just scratches means I polish.
It seems like you tired of your Swiza pretty quickly. Imagine what the white scales would look like after carrying them a while. I think I would still buy one if I found a used one somewhere. Best wishes. Gary

-
I did order a new pair of the same color, I donβt want to use them from the Cybertool.. and the used blue ones are only there until I get the new scales next week..
Whit the Swizza, yes maybe I would have to get use to its flaws, but itβs also a good collection item..
-
I have one or two white scaled SAKs and just pulling them in and out of jeans causes them to turn a bit blue. I ended up just cleaning and polishing them and making them shelf queens for now. Though the white really does stand stand out.
-
Ok now I have a picture of my fresh swapped Huntsman and the Cybertool

-
Looking good!!

-
It was about that divicult to get them on the huntsman like it was on the Cybertool ^^
I dont know if these Scales where Original Victorinox, i did not looked on the backside ..Where non transparent Plus Scales even something you get at Victorinox?
They look nice, the only thing i notice is that the Tweezers are a bit less stiff secured in its hole, its not that they fell out easy, : they dont fell out from gravitation, but they have a bit less friction like they had Originally..
-
Make sure the scale on the tweezer side is fully seated. If the scale isn't fully against the liner, the tweezer will be loose. Hold it up to the light sideways and see if there is any light coming through. I don't know how you are trying to seat the scales. I pad them with a piece of cardboard and use a C-clamp. That way I can put all the pressure on the spot just above the rivet. Best wishes. G
:) -
I did looked now: seems like there is still a gap, I press them on by putting the SAK in an Sock to secure it from scratches and then give some pressure by standing on the scale ^^
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better π
Register Login