December 2025 Tool Box Challenge
-
Our friend Looper wanted me to show a photo of a Chapman screwdriver, I think? Maybe it was a Coleman sleeping bag. Probably not the last one. I will post a photo of an old Chapman. The later models had a plastic caddy. Best wishes. Gary

[attach id=0 msg=2553079]
-
@IMR4198 said:
Most one-piece tools are a fail. Ones that are only screwdrivers, or a pry tool are fine.I am thinking of carrying this little chap:

I figure that is valid, as the teardrop cutout is just there to assist in pulling nails, which is one of the main uses for a small pry tool, not a different function.
-
@IMR4198 said:
Our friend Looper wanted me to show a photo of a Chapman screwdriver, I think? Maybe it was a Coleman sleeping bag. Probably not the last one. I will post a photo of an old Chapman. The later models had a plastic caddy. Best wishes. Gary

[attach id=0 msg=2553079]What a beautiful mini ratchet set!

Where have you been hiding it?
-
@IMR4198 said:
Our friend Looper wanted me to show a photo of a Chapman screwdriver, I think? Maybe it was a Coleman sleeping bag. Probably not the last one. I will post a photo of an old Chapman. The later models had a plastic caddy. Best wishes. Gary

[attach id=0 msg=2553079]Perfect!
The bits having the friction ball in the bit are older, and was not sure you were describing what I was picturing behind my eye lids.👍👍👍
-
I had another mini ratchet like the one in the Chapman kit. They came on the Lyman 450 lubricator/sizer. There was a stem at the top which threaded down to put pressure on a plunger. The ratchet made one hand operation easy.
I used the Chapman fairly regularly along with some standard screwdrivers and such. Also a Mototool. I still have all of them, but don't use them much at all now. The extension fits either the handle or the ratchet. There is a set screw on the side of the handle to lock the extension. The bits have a knurled end to them. Sometimes when reassembling something, it was convenient to turn them with your fingers without any handle. Almost impossible to cross-thread something that way.
Best wishes. Gary

-
How far do you have to carry these tools for them to count? I have some upcoming workshop stuff in December which could be a good match, but lots of those tools would hardly be considered EDC. More like carriable, and then not too far..
-
It is not necessarily about carrying the tools, it is about going COLD TURKEY AND NOT CARRYING A MultiTool or Swiss Army Knife or a Multi-Functional Flat Tool
What we may select as if these items are not in our tool set.
A pliers, screw driver, pocket knife. As basics. Or, just a pocket knife.
-
Let me ask friend Vidar a question. What do you carry with you during your everyday life? I'm not interested in your workshop tools. Best wishes. Gary

-
Normally not much or a pocket SAK. A SAK or plier based multitool if doing relevant work. Some work clothes are preloaded. :)
Well, I guess that what was the answer. My tool box is pretty full, but those are definitely workshop tools for the most part.
-
It might be helpful to read a few pages of the posts from the last time this challenge was held. That would be a good way to get a feel for what it is all about. Best wishes. Gary
/post/2284896 -
Yes, those seem to be EDC sized tools. I just got confused about where to draw the line with the Tool Box heading, but the old thread made that a lot clearer.
-
@IMR4198 said:
Our friend Looper wanted me to show a photo of a Chapman screwdriver, I think? Maybe it was a Coleman sleeping bag.
@fullbreakfast said:
I am thinking of carrying this little chap:Please do!
Is there an NSN on the other side? -
I got out a pry bar yesterday. The only one I ever had, except for really big ones for prying apart parts of a building or something. A friend here sent me one for Christmas along with some other things. I said thank you for the various items and for the chisel. I was informed that it wasn't a chisel, it was a mini pry bar. Oops.
I VERY rarely pry anything. I sometimes use a screwdriver for something like that. Evidently I am in the minority judging from the number of bent knife blades and tools I see on used SAKs. I might carry my cute littlechipry bar during the challenge. It doesn't take up much room in a pocket. Best wishes. G

-
I know GARY has done a great job preparing us for this challenge.
As I have shared, having specialized tool kits has been my style since I started working in the electronics field service industry, 1973.
Today I visited the back of my pickup and retrieved a kit stored in my Stanley rolling tool locker.
[attach id=0 msg=2553215]
This kit was assembled about 1979, was lighter that a briefcase style grip, was used for repairing train printers, vertical tape stands, disc packs, and installations mainframe systems that filled a 40’ x 60’ computer room.
The only tool missing is my FLUKE multimeter, it is on loan to my son.I was actually searching for one of my small screwdrivers, but not there.
This was last used a few years ago at the PT gig at the Y, requiring and changing a display panel on the control panel for the lighting system that talked to the power control station in the electrical room.

-
I'm pretty sure I saw a small screwdriver in there somewhere? I sifted around in my own screwdriver box and found a pretty good small one myself. Didn't know I had it.
My local Walmart installed those scanners that you pass between when you go in or out. That was a number of years ago after the new location was opened up near my house. I figured out I would do a little test on those things. I put a full-sized vise grip in a coat pocket. Pretty hefty piece of steel. Certainly enough to simulate a weapon of some sort. Walked right in. Nothing. Looked at some things in the store and attempted to walk back out. What happened? Nothing. Naturally I was prepared to defend walking around with a large pair of locking pliers with some sort of excuse.
Whatever those scanners were supposed to check for, that wasn't it. Do people bring their dogs in the Walmart stores where you folks live? They sure do where I am. I saw two dogs during my last hasty visit. I asked my sister, and she said that she had never seen a dog in the store where she lives. These two were on leashes. Sometimes they put them in the shopping carts. I saw one older woman with a small dog in the kiddie seat of a shopping cart wrapped in a blanket. Leaving a trail of dog urine behind her on the floor. Lovely.
Best wishes. Gary

-
@LoopCutter said:
I know GARY has done a great job preparing us for this challenge.As I have shared, having specialized tool kits has been my style since I started working in the electronics field service industry, 1973.
Today I visited the back of my pickup and retrieved a kit stored in my Stanley rolling tool locker.
[attach id=0 msg=2553215]
This kit was assembled about 1979, was lighter that a briefcase style grip, was used for repairing train printers, vertical tape stands, disc packs, and installations mainframe systems that filled a 40’ x 60’ computer room.
The only tool missing is my FLUKE multimeter, it is on loan to my son.I was actually searching for one of my small screwdrivers, but not there.
This was last used a few years ago at the PT gig at the Y, requiring and changing a display panel on the control panel for the lighting system that talked to the power control station in the electrical room.
This is great. The experience that must have gone into building it up is obvious, and makes it so much cooler than any pre-packaged tool kit ever would be. Respect!
-
@Gary - Yes, the orange/black handle is a screw driver, just not the one I was searching. I wanted one of mine that has both flat blade and Phillips.
Also, the sensors you observed at your Walmart and other stores were not configured for metal detection, though they can be and are used at schools, hospitals, government buildings and even airports.
At retail stores they are configured to sense a RFID tag that is placed into packages, or price tags, even clam shells packages. Often items valued above $8 retail.
RFID = Radio Frequency Identification. These broadcast a signal, if close to a sensor an alarm will go off.
When you scan your purchase, that RFID tag is disabled or turned off. If the internal battery is exhausted, the tag is of no value, however I am not aware of the battery life cycle. It was suspected a year or more!@fullbreakfast - it did take some time to refine and tune the kit. It also was always evolving depending on new equipment, types of fasterner heads,
Most of the drivers are based off the excelite interchangeable driver bits and size of handles I was comfortable using.
-
I'm in.
- AzteCypher
- IMR4198
- ReamerPunch
- Farmer X
- cody6268
-
And welcome, friend cody. This might be the latest list. I don't know. Best wishes. G
- AzteCypher
- IMR4198
- ReamerPunch
- Farmer X
- fullbreakfast
- nate j
- LoopCutter
- Humayd
- Gra_farmer
- cody6268
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login