Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Vic 111mm Backside Phillips is PANTS!! (that's bad...)

Scheduled Pinned Locked Moved Swiss Army Knights Forum
59 Posts 1 Posters 12.8k Views
  1. Home
  2. Tool Talk
  3. Swiss Army Knights Forum
  4. Vic 111mm Backside Phillips is PANTS!! (that's bad...)
Vic 111mm Backside Phillips is PANTS!! (that's bad...)
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Mr. Whippy Offline
    Mr. Whippy
    Posts: 12,208
    Mr. Whippy Offline
    Mr. Whippy
    wrote on last edited by
    Quote Reply

      The design of the backside Phillips on the 111mm Vic tools is craptacular. I was testing it out as a T-handle tool and the thing completely failed. The Phillips head cut through the brass rod and bent the aluminum liner to smurf.

      Looking at it, it's a combination of soft brass and lack of material in the liner. If the there was a thick steel liner, it may have helped considerably. It's a totally inadequate design for this tool. >:(

      This pic shows the cut through brass pin.

      My plan is to replace the pin with hardened stainless steel, but honestly, the thin outside liner makes me think it'll fail again.

      Victorinox: This needs to be addressed. :(

      1 Reply Last reply
      • DaveK Offline
        DaveK
        Posts: 13,379
        DaveK Offline
        DaveK
        wrote on last edited by
        #1 Quote Reply

          Ouch!

          That's quite surprising Mr W - whilst I've not used that tool on a 111mm SAK, I always felt it was a bit more substantial than that!

          Warranty time?

          1 Reply Last reply
          • ICanFixThat Offline
            ICanFixThat
            Posts: 4,534
            ICanFixThat Offline
            ICanFixThat
            wrote on last edited by
            #2 Quote Reply

              Time to send it to Vic for Warranty.

              Never seen such a total faulire. How does the hole in the driver look, I'm thinking it would need to be pretty sharp to cut the rivet. It's true the rivets are not that strong against a sheer force, but maybe the bending of the liner allowed for a greater force to be applied. hmmm.

              Send it to vic and let us know what they say.

              1 Reply Last reply
              • Mr. Whippy Offline
                Mr. Whippy
                Posts: 12,208
                Mr. Whippy Offline
                Mr. Whippy
                wrote on last edited by
                #3 Quote Reply

                  Well,

                  I have a hardened steel pin that's just over 3mm. I'm going to sand it down to 2.5 mm and see if it functions better. The liner could still strip out, but we'll see.

                  If I send it in, I'll just get the same weak pins back, so I figure I'll try this first.

                  To be honest, if this doesn't work, I'll be abandoning the 111mm Vic as a serious EDC.

                  1 Reply Last reply
                  • thebullfrog Offline
                    thebullfrog
                    Posts: 2,277
                    thebullfrog Offline
                    thebullfrog
                    wrote on last edited by
                    #4 Quote Reply

                      Another score in favor of backspring corkscrews :D

                      1 Reply Last reply
                      • DaveK Offline
                        DaveK
                        Posts: 13,379
                        DaveK Offline
                        DaveK
                        wrote on last edited by
                        #5 Quote Reply

                          @thebullfrog said:
                          Another score in favor of backspring corkscrews :D

                          Lol!

                          @ Mr W - good point. Good luck with the beefing up. (I'm still surprised though)!

                          1 Reply Last reply
                          • jzmtl Offline
                            jzmtl
                            Posts: 8,551
                            jzmtl Offline
                            jzmtl
                            wrote on last edited by
                            #6 Quote Reply

                              Just because you can use it as a t-handle doesn't mean you should. :P I've broke hardened steel parts with the amount of torque a handle can provide, the brass/aluminum construction just isn't made to be that strong.

                              1 Reply Last reply
                              • stressmaster5000 Offline
                                stressmaster5000
                                Posts: 3,414
                                stressmaster5000 Offline
                                stressmaster5000
                                wrote on last edited by
                                #7 Quote Reply

                                  Ouch! :oops:

                                  1 Reply Last reply
                                  • Andreas Offline
                                    Andreas
                                    Posts: 1,178
                                    Andreas Offline
                                    Andreas
                                    wrote on last edited by
                                    #8 Quote Reply

                                      Wow that was a new one. I'm surprised you could apply that much torque, had to fit the screw perfectly - the corkscrew replacement phillips driver is notorious for being too large to be useful for most things

                                      1 Reply Last reply
                                      • Mike, Lord of the Spammers! Offline
                                        Mike, Lord of the Spammers!
                                        Posts: 42,975
                                        Mike, Lord of the Spammers! Offline
                                        Mike, Lord of the Spammers!
                                        wrote on last edited by
                                        #9 Quote Reply

                                          Now that is surprising :o

                                          Mind you, you did generate a hell of a lot of torque :-\

                                          1 Reply Last reply
                                          • BIG-TARGET Offline
                                            BIG-TARGET
                                            In Memoriam
                                            Posts: 4,312
                                            BIG-TARGET Offline
                                            BIG-TARGET
                                            In Memoriam
                                            wrote on last edited by
                                            #10 Quote Reply

                                              That is truly a first!! :-\

                                              1 Reply Last reply
                                              • Gareth Offline
                                                Gareth
                                                Admin Team
                                                Posts: 37,725
                                                Gareth Offline
                                                Gareth
                                                Admin Team
                                                wrote on last edited by
                                                #11 Quote Reply

                                                  Yup, that's a first for me too. I think you've got strong hands Nate. :-\

                                                  1 Reply Last reply
                                                  • Neil Offline
                                                    Neil
                                                    Posts: 15,287
                                                    Neil Offline
                                                    Neil
                                                    wrote on last edited by
                                                    #12 Quote Reply

                                                      Ouch! I'm another who's never seen that before and I've seen a lot of damaged SAKs. I'd send it back to Vic. anyway and have a nice new one to modify if that's your plan.

                                                      1 Reply Last reply
                                                      • Mr. Whippy Offline
                                                        Mr. Whippy
                                                        Posts: 12,208
                                                        Mr. Whippy Offline
                                                        Mr. Whippy
                                                        wrote on last edited by
                                                        #13 Quote Reply

                                                          This is my OH Locksmith. Don't think I'll get a warranty repair on this one... :-\

                                                          1 Reply Last reply
                                                          • Sea Monster Offline
                                                            Sea Monster
                                                            Posts: 4,261
                                                            Sea Monster Offline
                                                            Sea Monster
                                                            wrote on last edited by
                                                            #14 Quote Reply

                                                              I rarely use SAK phillips, so I've nothing to say on that part of it.

                                                              If it weren't for the custom jobby, I'd give Vic at least one chance at warranty before avoiding the whole 111mm line.

                                                              What I did notice as I was checking my 111mms for comparison.

                                                              The outer liner on my Three layer 111mms (OHT & Helmsman) is slightly thicker than the one on my two Layer 111mm.

                                                              I also noticed that the Inner liner on my OHT and (Dutch?) Army knife is steel, while the centre liner on my Helmsman is alloy. (I imagine that has something to do with the OHT and Army knife being Liner locking, while the Helmsman is Packlock)

                                                              Just some possible variables that might contribute to that sort of failure.

                                                              1 Reply Last reply
                                                              • Styerman Offline
                                                                Styerman
                                                                Posts: 3,572
                                                                Styerman Offline
                                                                Styerman
                                                                wrote on last edited by
                                                                #15 Quote Reply

                                                                  All backspring Phillips are only good for one thing , fistloads . as drivers they fail !

                                                                  Chris

                                                                  1 Reply Last reply
                                                                  • Mr. Whippy Offline
                                                                    Mr. Whippy
                                                                    Posts: 12,208
                                                                    Mr. Whippy Offline
                                                                    Mr. Whippy
                                                                    wrote on last edited by
                                                                    #16 Quote Reply

                                                                      Well,

                                                                      Looking at this rigorously,

                                                                      If the Phillips head is normal to the plane of the screw/bolt, and force is applied normal to the handle surface we can figure out the torque. I figure maybe 60 lbs (260 newtons) of force applied, 1/2 to each end of the handle gives a torque of:

                                                                      2(0.045m X 130N)= 11.7 Nm torque

                                                                      From a website giving assembly specs for steel bolts,

                                                                      a #4 grade 5 steel bolt (diameter of 2.8 mm, that's 10% bigger than the diameter of the 2.5 mm brass pin), dry assembly torque is 2 Nm

                                                                      This was 6 times the assembly torque!

                                                                      Oh, and this little bit from a site regarding bolts and materials

                                                                      Brass
                                                                      Brass is an alloy of primarily copper and zinc. Brass is highly corrosion resistant and electrically conductive. However, its use as a fastener is somewhat limited due to its relative softness. It is used primarily for its appearance.

                                                                      I think it is safe to say that the backside Phillips is under-engineered. Even if the outer liner was as stiff as a regular backspring, I suspect the brass would begin to stretch, fatigue and eventually fail, given the arrangement in the tool.

                                                                      I'll replace the pin, but I don't hold much hope for this as a goto farm tool... :-\

                                                                      1 Reply Last reply
                                                                      • WhichDawg Offline
                                                                        WhichDawg
                                                                        Posts: 7,559
                                                                        WhichDawg Offline
                                                                        WhichDawg
                                                                        wrote on last edited by
                                                                        #17 Quote Reply

                                                                          wow Mr. Whippy! very interesting and thanks for that. (and sorry it broke on you)

                                                                          I do not like the back philips but so many of my country-people (usa) like it.

                                                                          Mainly because we are not a big wine drinking country and idea of a philips
                                                                          instead of a corkscrew appeals to so many here (just my opinion) ::)

                                                                          In my case, for me when I first started getting into SAKs I wanted philips and
                                                                          not the corkscrew, even the backspring one.

                                                                          (scene from 2010) "I didn't know...I didn't know!"
                                                                          How inconvenient it was and impractical, and you have just increased that notion!

                                                                          but I have learned, from the smart people here and at SOSAK! ty sir :salute:

                                                                          1 Reply Last reply
                                                                          • Mr. Whippy Offline
                                                                            Mr. Whippy
                                                                            Posts: 12,208
                                                                            Mr. Whippy Offline
                                                                            Mr. Whippy
                                                                            wrote on last edited by
                                                                            #18 Quote Reply

                                                                              Update: Repaired.

                                                                              A few pictures:

                                                                              The sheared brass pin:

                                                                              Both pieces of sheared off brass pin. New hardened steel pin in place:

                                                                              The repaired liner. The steel pin donor next to it. Scales back on:

                                                                              Beauty shot of the tool with Donors and Deceased. :)

                                                                              1 Reply Last reply
                                                                              • glorn Offline
                                                                                glorn
                                                                                Posts: 1,223
                                                                                glorn Offline
                                                                                glorn
                                                                                wrote on last edited by
                                                                                #19 Quote Reply

                                                                                  I'll stick to a corkscrew. If the screw is that hard to get out, I'd rather just skip the whole thing and drink wine until someone arrives with a proper driver.

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  • 3
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. Swiss Army Knights Forum
                                                                                  4. Vic 111mm Backside Phillips is PANTS!! (that's bad...)
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0