Vic 111mm Backside Phillips is PANTS!! (that's bad...)
-
Science!
It's the only way. I didn't have another 111 mm to use as an experiment so I picked out this 2 layer 91 mm SAK.
Here are the testing gear: NE size socket, SAK, Torque wrench:

I placed the SAK in the Vise so that the edge of the tool is free, that way the vise isn't acting as outer liners:

Long story short, I don't have an inch-pounds torque wrench. The tool failed at less than 10 Nm! :o

The failure appears to be EXACTLY the same mode as my 111 mm SAK. The Brass was cut through when the liners gave way.

Conclusion:
The backside Victorinox Phillips is in NO WAY to be confused with a T handle driver. Best used for pre-loosened screws. :(
-
See, I don't see it as a T-driver. I just see it as a driver hanging off the back of a backspring.
I doubt any of it is as strong as the "real deal" but that's the price you pay for compactness and the range of tools it offers.
Question is, is 10 NM the same as that of the 111mm SAK?
-
Less than 10 Nm.
10 Nm is about what an oil drain plug is torqued. Really not much. This Phillips can't really be trusted to remove anything of a mechanical nature. Trim pieces, electronics screws and maybe some wood screws. That's about it.
Again, not a real Farm EDC tool. :-\
-
Well to be honest how strong did you expected it to be? Brass is as soft as it gets, not even mild steel can be peened the way brass pin is, let along compare with heat treated tool steel used in real drivers.
MT just aren't made for high stress uses, I remember a guy used his wave bit driver in 90° position to get more torque and shattered the bit holder.
-
Following your lecture on Engineering (and home cooking) two of my favourite subjects, as it turns out, but that's another matter.
It could be that after the mod the distances between tool shank and liner were ever so slightly increased allowing some rotation of the Driver, contributing to (if not the sole cause of) the failure of the pin.
I'm not saying it wouldn't have broken anyway, as the nutter with the torque wrench indicates, just that it might have helped.
-
Thanks for these interesting insights!!! I just love my Trailmaster, and I love having a phillips driver on it. Now I know that I have to be careful with it. I used it once with quite loose screws on a geocache, and I wanted the phillips driver for exactly such applications. But you newer know when you need one and have nothing but your SAK with you... now I know that I don't want to use it for reall heavy use :ahhh
-
@Turnstone said:
..... now I know that I don't want to use it for reall heavy use :ahhhOr you could say you know to clamp the vice grips in the center of the knife and use them as a lever for those heavy use jobs. ;)
I hope every one realizes that Torque and Phillips never did get along regardless of the driver.
-
How much more torque would it be able to stand if the pivot area of the phillips (where the hole goes through) were made square, instead of round?
-
Dunno... ???
I don't know really what it would take in torque. I don't have an in-lbs torque wrench. :-\
-
I've always lived by the rule only to use SAK tools (except for the knife blades) when a dedicated tool is not available. I've always felt the back side driver pin is too small in diameter.
-
I'm wondering now if the hook can really carry 250lb with a jolt? that's a lot of force on such a thin pin

-
I don't have an in-lbs torque wrench
For those of us in....well, everywhere else in the world, what's the benefit of in-lbs over N.m?
-
@Sea Monster said:
I don't have an in-lbs torque wrench
For those of us in....well, everywhere else in the world, what's the benefit of in-lbs over N.m?
ft lbs about 25% more than Nm. An in lbs torque wrench is for tiny torque measurements (because an inch is 1/12th of a foot).
1 N m = approximately 0.75 ft lbs
1 Nm = approximately 9 in lbs.
My torque wrenches are for mechanics (cars, tractors and motorcycles) I have no need for in lb torque wrenches
-
@Mr. Whippy said:
@Sea Monster said:
I don't have an in-lbs torque wrench
For those of us in....well, everywhere else in the world, what's the benefit of in-lbs over N.m?
ft lbs about 25% more than Nm. An in lbs torque wrench is for tiny torque measurements (because an inch is 1/12th of a foot).
1 N m = approximately 0.75 ft lbs
1 Nm = approximately 9 in lbs.
My torque wrenches are for mechanics (cars, tractors and motorcycles) I have no need for in lb torque wrenches
You previously had no use for in lb torque wrenches. Now you need to get one. And smash up more stuff :D
-
I am hoping oversized stainless steel might help a bit. Especially if they go through the thickness of both scales as well.... ;) (high grade aluminum alloy, haven't made them yet) At this stage of modding, fashioning new stainless steel liners would be easy enough to do as well.....

-
We need to hear more about this one...
(I think a stainless steel liner on the Phillips side would help.)
-
with some very dodgy, theroetical calculations, the hook on a backspring should take 250 lbs, (non shock load) before the pin fails.
Anyone got a sacriSAK and 250lbs to hang off it?
-
I just remembered something. I was using the awl on 91mm SAK to drill through eyes of a coconut, as it starts to penetrate the shell, I can feel the awl start to bind, and parts are flexing, I didn't apply a lot of torque to it, but I guess that's about all the stress aluminum/brass can take. Then again coconut shell is way harder than any wood I know.
-
Hats off to Mr. W for carrying out that test.

Now just a hundred or so more tests like that, on knives of various ages, and we should have some quite decent statistics. :DI've got to say in defence of Victorinox that 10Nm is quite a lot for a small screwdriver. It's more than I can comfortably exert on a medium-sized screwdriver handle without using both hands. It's also enough to properly tighten an M8 bolt, and enough to completely destroy an M5 bolt.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login