Vic 111mm Backside Phillips is PANTS!! (that's bad...)
-
But are we to treat that driver the same as a T-driver? Are we really to expect the same performance out of a 111mm SAK as the "real deal"? (I'm just stirring it now :D)
-

I've never come across any SAK however abused that has a snapped pin. So this is really weird. I've seen deformed liners before but on corkscrew SAKs. These normally have bent corkscrews as well. I've seen older SAKs where every liner has split in two! but even then the pins were all OK. Its proper bizarre :ahhh
-
@Mr. Whippy said:
But are we to treat that driver the same as a T-driver? Are we really to expect the same performance out of a 111mm SAK as the "real deal"? (I'm just stirring it now :D)
That's wot it looks like... ???
Are you proposing a poser Victorinox tool! :o
Not at all (and you know it
:D) but are we really to expect that level of performance out of a SAK? Surely we need some level of sacrifice for the sheer amount of function we have in such a small package, perhaps ultimate strength is that sacrifice? -
Cor blimey :o
I've never come close to messing up a Vic like that - I think Mr W must have very big butch hands!
Whether the tools should be expected to deal with such high torque is a goods question - should we asking someone from Victorinox this?
-
@Benner said:
What would constitute a failure though? How much torque should it cope with?My point is that the first effect of over-stressing the philips is to stretch the brass pin holding the knife together. Using the bottle-opener as a lever would have a similar effect. And once the pin-head fails, the liner and pin-shaft will inevitably cede.
Now this is a modified knife: the part which is critical to the integrity of the knife against transverse forces -- the pin heads -- is exactly the part which has been re-worked. Mr. Whippy's breakage may be due to the fact that it's difficult to re-make the brass pin-heads to the same strength as the original.
With brass being as soft as it is, I'm surprised not to see more of this kind of thing.
-
It appears to be a shear of the brass though, not the head?
-
As long as the pin is tight, the screwdriver is twisting against the liners and not the pin itself. As soon as the pin lets go of the bushes holding the knife together, the liners move apart (as in the photo) and the screwdriver is twisting against the pin. At this point the knife is doomed: the screwdriver is now twisting directly against the thin, soft brass pin, which is likely to fail immediately.
The pin head must have failed first, before the body of the pin was sheared through. If the pin head had not failed, I guess the knife would have held together.
I can't claim the modified knife was weaker in this respect than an ordinary model, but it's a possibility.
-
Science!
It's the only way. I didn't have another 111 mm to use as an experiment so I picked out this 2 layer 91 mm SAK.
Here are the testing gear: NE size socket, SAK, Torque wrench:

I placed the SAK in the Vise so that the edge of the tool is free, that way the vise isn't acting as outer liners:

Long story short, I don't have an inch-pounds torque wrench. The tool failed at less than 10 Nm! :o

The failure appears to be EXACTLY the same mode as my 111 mm SAK. The Brass was cut through when the liners gave way.

Conclusion:
The backside Victorinox Phillips is in NO WAY to be confused with a T handle driver. Best used for pre-loosened screws. :(
-
See, I don't see it as a T-driver. I just see it as a driver hanging off the back of a backspring.
I doubt any of it is as strong as the "real deal" but that's the price you pay for compactness and the range of tools it offers.
Question is, is 10 NM the same as that of the 111mm SAK?
-
Less than 10 Nm.
10 Nm is about what an oil drain plug is torqued. Really not much. This Phillips can't really be trusted to remove anything of a mechanical nature. Trim pieces, electronics screws and maybe some wood screws. That's about it.
Again, not a real Farm EDC tool. :-\
-
Well to be honest how strong did you expected it to be? Brass is as soft as it gets, not even mild steel can be peened the way brass pin is, let along compare with heat treated tool steel used in real drivers.
MT just aren't made for high stress uses, I remember a guy used his wave bit driver in 90° position to get more torque and shattered the bit holder.
-
Following your lecture on Engineering (and home cooking) two of my favourite subjects, as it turns out, but that's another matter.
It could be that after the mod the distances between tool shank and liner were ever so slightly increased allowing some rotation of the Driver, contributing to (if not the sole cause of) the failure of the pin.
I'm not saying it wouldn't have broken anyway, as the nutter with the torque wrench indicates, just that it might have helped.
-
Thanks for these interesting insights!!! I just love my Trailmaster, and I love having a phillips driver on it. Now I know that I have to be careful with it. I used it once with quite loose screws on a geocache, and I wanted the phillips driver for exactly such applications. But you newer know when you need one and have nothing but your SAK with you... now I know that I don't want to use it for reall heavy use :ahhh
-
@Turnstone said:
..... now I know that I don't want to use it for reall heavy use :ahhhOr you could say you know to clamp the vice grips in the center of the knife and use them as a lever for those heavy use jobs. ;)
I hope every one realizes that Torque and Phillips never did get along regardless of the driver.
-
How much more torque would it be able to stand if the pivot area of the phillips (where the hole goes through) were made square, instead of round?
-
Dunno... ???
I don't know really what it would take in torque. I don't have an in-lbs torque wrench. :-\
-
I've always lived by the rule only to use SAK tools (except for the knife blades) when a dedicated tool is not available. I've always felt the back side driver pin is too small in diameter.
-
I'm wondering now if the hook can really carry 250lb with a jolt? that's a lot of force on such a thin pin

-
I don't have an in-lbs torque wrench
For those of us in....well, everywhere else in the world, what's the benefit of in-lbs over N.m?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login