Re: First mod - mini Farmer with scissors
-
-
Thank you for your kind words ladies and gentlemen.
Iām very glad that you found my thread useful.This is a how we set a rivet and make the head round.
Remember: BACKUP IS EVERYTHING.
And some very useful reading:
http://www.thefullwiki.org/Rivets
http://www.bladeforums.com/forums/showthread.php/701748-Sharp-edges-on-peened-rivets
http://www.homemodelenginemachinist.com/index.php?topic=4335.15
http://www.mtfca.com/discus/messages/80257/82578.html?1235094026
http://www.snydersantiqueauto.com/modelaparts/rivetsrivettools
The Advanced Knife Makers Manual
I may make a black alox farmer with scissors for a friend next month and Iāll try to focus on details about riveting.
This is the most difficult part when customizing an alox SAK.
All the other steps are quite easy and all we have to do is to be methodical.To be honest Iām not very satisfied with the rivets on the orange mini farmer of this thread. Experience is something we cannot buy. I hope my next project will be better.
All the best
Aris -
Very useful links and information!
Many thanx - I would need just it!Doc.Skipper
-
-
A very simple turorial with animation. Press the yellow button.
-
I hope you don't mind Aris, but the rest of the mods and I felt there was some excellent info on page 2 and 3 of your thread so we decided to make it a 'sticky'.

-
-
When I started the modification of the alox Bantam I faced all kind of problems and I made any possible mistake.
I thought I was well prepared because I studied much about modding and rivets.Theory is invaluable but when we go to the workshop things look different.
We can play war games all day long in the computer but when in the field of at the shooting range our weakness and lack of experience betray us.Modding alox SAKs is all the rage. Alox does not forgive mistakes and our work is exposed. The are no cellidor scales to cover the poor workmanship.
Iāve studied a lot about rivets and rivet setting before getting started. Riveting is the most difficult part when modding an alox SAK and can lead to fatal errors.
Everything else is reversible but mistakes when riveting may destroy our work.So letās get started. Weāll use the destroyed Bantam for demonstration.
When things go bad
We missed the Center of the rivet
It was not our lucky day, meaning we were careless and hasty.
We tried to remove the rivet of the scale-donor with the drill and punch method but we had a slip and the drill drilled the alox scales near the rivet.
If that happens to the Bantam we just throw it away and get a new one.
But what if we drilled wrong our beloved, expensive and discontinued blue farmer?No matter how loud we cry and curse, the hole will be there forever and we can not call this ācharacterā.
Without a press we cannot make the head of the new rivet wide enough to cover the hole. The head of the rivet will eventually crack and break if we try to make it extra wide.
So our project failed before it even started.But there is still something we can do.
One of our donors is probably a cellidor SAK. And after we disassembled it we had those spare rings:
Maybe we can use them to correct our mistake.
Letās do this.This is the drawing of the ring:


We widen the hole and insert the ring. This will support the rivet.






We set the rivet on the other side:

If we use our ball peen hammer with a little patience we can make the ring/rivet system to look like a massive rivet. One body one soul:


I think itās better to have a rivet with a big head that to have a hole near the rivet.
The diameter of that head is 5mm. A normal one would be 3mm. Anyway a 5mm head is not that huge after all. And finally we convince our selves that weāve made a rivet and knife with ācharacterā, one of a kind etc.
Conclusion
We better use a guide or even better a vertical base for the drill. There are bases with a vice which hold the knife securely.


The knife explodes
We forgot to tie the knife with tape and it exploded.

There is no need to remove the already set rivets and start from the beginning.
With a thin screwdriver or something similar we can push the backspring and the blade goes back to the right position.
If we are making a SAK with 3 or 4 layers this is tricky but we will get there eventually.
The exposed part of the pin which will form a round head is too long.
If we keep on hitting with the hammer this will lead to a rivet with cracked head because of metal-fatigue. And after too many strkes the possibility to hit the scales is raising dramatically. Also the finished knife will most likely have a noticable horizontal blade play.
We better shorten the pin with a file. If we have already started and have a nice round head say 0.7 or 1mm away from the scales then itās better to file the head or a part of it and then continue with the hammer.
The finished knife is too tight and the blades do not close with the backspring action.
We oil the joints and see if it improves.
If not we open an opener and stretch it horizontally. This will stretch the rivet a bit and this is enough in most cases.Not all parts (scales, backsprings, blades) are on the same axis.
This is caused because of a wrong hole (not fully centered) or a bent pin.
That will maybe lead to a blade which does not fully opens and this is an accident waiting to happen.We can baton with the knife with care and not much force. We do not hit the spine near the tip or in the middle but near the pivot. A few light hits and we try the blade and so on.

This will bend the brass pivot/pin slightly and the blade will fully open.
If the problem is a big one or if we baton too hard, then weāll finally have a noticable vertical blade play.If we are working with black alox scales and scratch them, there is a nice product for black anodizind.


I have used it to anodize black flashlights and aluminium gun parts and works great. However it doenāt give a hard anodizing but only a very thin and quite sensitive anodized layer.
Our limits
If you are a novice like me and youāve made an acceptable and functional rivet and you notice that you do not see a serious improvement any more then stop!
We may think that with a few more hits with the hammer weāll make that rivet perfect.
Well, the possibilities are that weāll crack the head or hurt the scales. Besides excessive hitting may lead to a bent pivot and the blades will lose the initial axis.The difference between an acceptable rivet and a perfect one is not just a few hits but few months or years of experience.
Letās face it, we are not Scibeer and we better be happy with what weāve achieved.As an engineer and remote control model airplane modeler Iāve seen too many damaged projects for the sake of perfection.
-
Hand rivet tools
Rivet squeezer

This is the most advanced and precise tool.
It is used in aircraft industry.
The tool together with the dies may cost $150-200 or more.
If we are modding SAKs on a regular basis then this is maybe a good investment.If you are like me and just want to make your dream SAK, then make another 2 or 3 for your buddies and then quit, that tool is probably not an option.
U-clamp squeezer

This is usually a custom made press/squeezer made from a U-clamp.
The end of the screws must have a proper concave hole to form the head of the rivet.
This hole is easily made with a round drill.Rivet punches

Like the ones Iāve made with a lathe.
If we adapt them to some kind of custom made press or guide for hammering then this tool is excellent.
Just hitting with the hammer is dangerous and it will eventualy hurt the scales.All rivet tools require that the excess rod which will form the head of the rivet has the right size.
If itās too short the die will not form a complete head and will eventually hit the scales of the knife.
If itās too long weāll have a metal āflowā outside of the die or the pin will bend.Ball peen hammer


The well known basic tool for making a round head rivet.
Widely discussed in the forum.Screw posts


Iāve searched the world to find the proper size for my mini-Farmer project but couldnāt find 2.2 mm screw posts.
The thinnest I found was 5mm brass screw posts and solid brass extensions
This was my second and possibly the last contribution to the mod squad as this is all the knowledge I have about modding a SAK so far.
I cannot see how we can make our custom alox SAK better.
The rest is experience and experimenting.Once again I hope you found it useful.
all the best
Aris, Greece -
-
Fantastic primer!
Thank you for putting this together!

-
-
harryf3
Another perfect post! You sholuld issue it as paper or hardback


-
-
Very useful info. Especially for us "newbies" into the SAK mods.
-
-
-
-
Excellent

Not just a run of the mill 'Farmer with Scissors' but a Mini Farmer with Scissors

I can only imagine the disaster if I tried that :ahhh
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better š
Register Login