A "how-to" for basic SAK mods. Pic heavy.
-
Thank you... high praise indeed, coming from both of you!! It's been a fun learning experience.
Still a lot to learn, and somewhat addictive too. :DI polished the contact surfaces of that hammer, it seems to make it "stick" (if that makes any sense at all) less to the brass rod when edge peening. I was also kinda suprised I could not find quality 4 oz. and 8 oz. ball peen hammers locally. Had to order the hammers online.
-
That does make sense, I like to keep my balls shiny as well .... that sounds so wrong :-[
I've got a few hammers now, that I've picked up from car boot sales but when I first started assembling SAKs I had to order a couple. Turns out that locally I can only get huge hammers ::)
-
@Gareth said:
You're very welcome Gimmeabreak, I look forward to seeing the finished piece.
s
This one goes everywhere with me. I'd like it one layer thinner for EDC but I refuse to give up any of the tools to make that happen. Sadly, the magnifying glass get the least use but it ups the cool factor enough to keep it in place.

Thanks again for the tutorial. My next project is a Midnight Rambler with whistle scale while somehow keeping the toothpick/tweezers on board. I'm off to do more research.
-
Very nice mate.

-
Hi lads
,
need a pen in your 84 mm Waiter?
You can see following pics; I tried to make some photo-tutorial ;) -
Well done,sir!
-
This is the result.
The scales call for the polishing ;) -
@Doctor.Skipper said:
Hi lads
,
need a pen in your 84 mm Waiter?
You can see following pics; I tried to make some photo-tutorial ;)So you don't put any glue at the end were the tooth pick & pen go in
, I would be tempted to put a small amount on the SAK's pin at that end
but I guess you would run the risk of clogging up the tooth pick & pen's slots doing that
.
The plastic scales should still click into place , I have wondered about the challenge of gluing wooden scales without clogging up the scale tool's slots
.
I have wondered if smearing petroleum jelly into the slots would stop the glue clogging them up

-
@MultiMat said:
So you don't put any glue at the end were the tooth pick & pen go in
, I would be tempted to put a small amount on the SAK's pin at that end
but I guess you would run the risk of clogging up the tooth pick & pen's slots doing that
.
The plastic scales should still click into place , I have wondered about the challenge of gluing wooden scales without clogging up the scale tool's slots
.
I have wondered if swearing petroleum jelly into the slots would stop the glue clogging them up

You are really right - the scales keep very well without adhesive as well.
But - there is something ... I can´t express it - something like untightness, that occurs and that irritates myself. (Epoxide can solute ethanol/clear alcohol as well. Light dust is the rest of milling and can be removed easily.) -
hi first post, been lurking for a while.
thanks for this tutorial, i've been following it trying to take the saw from a camper and put it in a super tinker.
dis-assembly, like in most cases, was pretty darn easy.
i'm having a slight problem when attempting put the camper back together minus saw. (doing that one first as test run)
the spring pieces seem to want to pop off the center pivot pin even after i get a layer situated.
is there a trick or something i am missing to keep it from popping off?
thanks
-
First let me say, welcome to the forum.

I have to admit I'm not quite able to visualise exactly what is going wrong for you, if you are getting both ends of the spring located under their tools I can't understand how it wouldn't stay exactly where it should be in the centre.
I suspect I am misunderstanding the question though.Perhaps someone who's brain isn't quite so tired might be of more help right this minute. :-[
-
Wait, wait! I think I might have just got what you were saying. If we are talking about the blade layer am I right in thinking that the spring is jumping off the corkscrew? Someone (and I forget who now) once suggested that using big bulldog clips to hold the layers together while building can help keep everything in place.
-
honored to have you answering my noob questions.
i got it figured out what i was doing wrong. I wasn't putting the back accessories and pin in for some reason misthinking i would do it later.
once that stuff goes in, everything is held together
thanks again for the response and for the post.
I got my camper back together minus the wood saw (so it's a homemade spartan now i believe)
whew for a noob, and i should say i was working with brass stock that was hardware store bought 3/32 and nail the proper size for the 2.2mm center pin.
I'm going to try it for a few days to make sure it's solid and then start to work on the other one.
I was thinking of taking bottle and can open layer off super tinker and add wood saw.
I wanted the phillips instead of corkscrew.
think i saw that mod in the huge mod thread, which i looked at every pic :sak:
-
for the corkscrew i found it was easiest when it was extended to get the spring in place.
also this project gave me a proper respect for my LM wave, very helpful tool to have around when doing this sort of stuff....
-
very glad to hear you got it sorted WiSAKfan.
Now we really do insist on you adding pictures of your mods when they are complete.
:D -
well i took it apart again,
was thinking of going a nice slim package of big blade, small blade, saw and awl on back under blades but it doesn't seem to be the right fit
perhaps the corkscrew is sized to go under the blades?
-
Normally the corkscrew is the back tool for the blade layer and the awl for the caplifter layer.
-
yeah i know that's the way it normally is....
I removed the caplifter layer but wanted to use the awl in place of the corkscrew.
with the awl in that spot the big blade doesn't want to snap open
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login