Scissor test
-
-
Any day the Wave comes out fine is okay by me...
I mentioned this in another thread, but I was present at a situation where a nurse had to apply a tough, pre-medicated bandage to a person's wounds. This bandage reminded me of fiberglass muffler patch with a gooey layer on top. For some strange reason, her medical scissors would not cut the bandage cleanly and only succeeded in messing up the medication layer. This was one of those situations where you produce the multitool and people who've never seen the light think you've just stepped out from one of those Monoliths in "2001: A Space Odyssey".
Anyway, she and her associate were very skeptical, but were then stunned when the Wave's scissors cut through the goo and bandage like a lightsaber. When the stress was over, she said she was going out to get a Wave. I on the other hand couldn't wait to get it home and clean it.
-
Thanks for the info!
I use the scissors on my tools quite a bit actually. Mostly for cutting paper and thread but other things crop up too. In general I've found the scissors on an MT tend to be better for tougher materials, while the scissors on my SAK's are better for precision work.
-
For paper, I love my Crosscut. It'll also do thread fine, but the tiny scissors on a Vic Classic seem more 'maneuverable'... easier to get into small places.
For being as tiny as they are, the Vic Classics still cut through the seam of khakis (4 layers thick). It was slow, but it happened. I was frankly amazed how much work they could get done.
The scissors on both the Wave and MP400 were GREAT at small tasks, high precision, and chewed through most anything. I think for 'heavy duty' tasks, any of the MTs whose main tool is scissor heads will work better for really heavy cutting.
I have to say I'm rather sorry I don't have a wider selection of swiss army knives to test. The test here was intended strictly for plier/scissor based multitools, not SAKs, but I thought the Vic Classic was a good benchmark tool for comparison... and I had one handy.
Biru: the Wave scissors are top of the heap next to the Gerber MP400. They are, honestly, amazing to me. I hadn't expected that kind of performance, even after messing around with them a bit. However, while they're great across-the-board performers, for day to day likely tasks, the Crosscut and Squirt will outperform them.
dks: The scissors on the Micra are identical to those on the Squirt I tested. So you can just reference the Squirt's results (which were quite good). Sadly, I had no Surge or Juice for the line-up, but the linked video covered those. So, it should give you an idea where they fall compared to my tests.
-
-
Great tests ! Quite a span of materials and tools, and quantifying with results by numbers makes sense.
-
@Lynn LeFey said:
dks: The scissors on the Micra are identical to those on the Squirt I tested.Similar, but not identical (see picture with the noticeably rounder tips of the Squirt). I prefer the Micra ones, though they probably perform the same.
I also included a picture of the Squirt S4 and PS4 (smaller) scissors for reference
-
How about we agree on 'functionally identical'
I unfortunately didn't have a PS4 for comparison. I would have liked to test their smaller scissors, particularly in comparison to the excellent Vic Classic pair.
-
-
One more tool tested, Scissors on 91mm Victorinox (Explorer).
This knife came to me in very used condition. It's a pre-1991 model, and has a screw holding the scissor blades together. I took them apart, did a very minor sharpening to them, and reassembled. They are in very good condition. So, while not new, I suspect they'll react about like a new pair.
My biggest complaint with these scissors was that for more difficult material, where more lateral force was needed, the spring would pop out from under the handle. Annoying, but not a deal-breaker. Otherwise, for scissors that are over 20 years old, I am highly impressed.
Vic 91mm Scissors: Failed lid, Barely adequate for 550. Pass PETE and non-corrugated cardboard with distinction. Pass paper, cardboard, t-shirt, khaki. Score: 7
-
Never tried it myself , but some Dude on BF claimed to have cut 12ga. solid copper wire with the scissors on a classic . Without any damage !
He had apparently bought up a bunch , that had been seized by the TSA , so he didn't mind doing a "to destruction " test .
My personal preference runs to the Vic. scissors , I have found Wave/Charge scissors to be quite sloppy . My cutting with them runs to small /delicate tasks . For more meat and potatoes stuff , I have a pair of Kline Electrician's scissors on the back of my belt .
Chris
-
**Nice! Some great tests! ** I think at some point I'll have to do a scissors test. Just got in a new pair of shiny stainless steel Vic scissors rated at 60HRc. They are 8" scissors, but the cutting edges are only 2.5". They do cut "very" well though. packaging says hot forged in Spain.
-
@ICanFixThat said:
**Nice! Some great tests! ** I think at some point I'll have to do a scissors test. Just got in a new pair of shiny stainless steel Vic scissors rated at 60HRc. They are 8" scissors, but the cutting edges are only 2.5". They do cut "very" well though. packaging says hot forged in Spain.Francis, we need to know more ...

Where from, obsolete or current, piccies, blah blah blah
-
For all the bad opinions written about the Charge/Wave scissors when they first came out, they seem to perform admirably well, both in the video and in your own testing Lynn.

-
I've heard a few folks talking about slop in their Wave scissors, which is weird. Mine are perfect. Absolutely no play in them.
I think it was Biru in another thread talking about them cutting a thick medicated pad for a nurse. Yeah, for me, they just cut through everything great. Same with the scissors on the Gerber MP400. They both have the slight failing that the Crosscut/Micra/Squirt S4 didn't, which is lack of leverage for hard cutting tasks. You can't have it both ways, though, and for their size the Wave's scissors are shockingly good, IMO.
I should add zip-ties to my future tests. That seems to be one of the real-world things scissors get used for on occasion.
-
Zip-ties are darn hard to cut. I use a toothpick -or scissors - to unlatch the teeth inside the clasper part.
-
I convinced my husband to try carrying a Micra for a while, instead of his Vic Classic, and the first real time he was impressed with it was when he had to cut a bunch of zip ties.
-
-
@50ft-trad said:
**Nice! Some great tests! ** I think at some point I'll have to do a scissors test. Just got in a new pair of shiny stainless steel Vic scissors rated at 60HRc. They are 8" scissors, but the cutting edges are only 2.5". They do cut "very" well though. packaging says hot forged in Spain.
Francis, we need to know more ...

Where from, obsolete or current, piccies, blah blah blah
I think it is current, or was recently current, gone from victorinox.com as far as I can tell with their region stuff and the information there seemed a little out of date. It could be that it is very new as well, i have not had time to check the catalog.
Model number is 7.6378, I'll get a picture up on the weekend. I see a couple on ebay mine came from Europe at 40 euros or so (not cheap).
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

