Electrical Help
-
I'd like to add a winch sometime, but my understanding with that is that you only use the winch with the motor running, which I would have anyway without the warning.
Def
Sent from my MB860 using Tapatalk 2
-
Well, the new alternator is in and happy, but it looks like I need a new starter too. If this keeps up I'll have a whole new truck soon!
Def
Sent from my MB860 using Tapatalk 2
-
As long as you always park on a hill you won't need that new starter ;D
Sent from my Galaxy Nexus using Tapatalk 2
-
Yes, although sadly I didn't park on a hill this time, I parked in the yard.

Ah well, I think I'll leave the starter for the mechanic next week rather than do it myself since he'll have it on the hoist for the welding anyway. So much for trying to get ahead!
Def
-
Bah, push start it, that's like a free gym membership. :D
The starter is literally a two bolt job, very easy to access and you can probably change it under 10 minutes.
-
Really? My Haynes manual says I may have to remove my exhaust or other parts to get at it.
Def
Sent from my MB860 using Tapatalk 2
-
Hmm, anything I've ever changed a starter on has always had enough clearance that nothing else had to be removed, but I've never looked at a TJ before to see how tight things are.
Ha, my old Bronco II I had to push start where ever I went. Use to get some funny looks when I would start pushing it than jump in and pop the clutch ;D
Sent from my Galaxy Nexus using Tapatalk 2
-
What? Remove exhaust? I took mine off to resolder wire between solenoid and motor and it was as simple as unplug and unscrew.
Did I ever send you the Chrysler factory service manual? Way better than Haynes. If not PM me your email and I'll send the PDF.
-
I think you did. I have them around here somewhere. Doesn't really matter though as a new starter is going to have to wait until payday anyway.
Def
Sent from my MB860 using Tapatalk 2
-
My wife was nice enough to buy me a new starter, which I just installed. I can see why the manual suggested removing the exhaust as it really got in the way! I had to take out a two inch long bolt about a half a millimeter at a time because that's all the space I had to work with- if the exhaust wasn't in the way I'd have about 70 degrees in which to swing the ratchet! Of course, the bolts were pretty well stuck and trying to get them out a half millimeter at a time was quite a chore.
What really pisses me off is that the damn thing still won't start. I plugged it in to my trickle charger, and it won't even respond to the key turning without being plugged in (understandable since it's been dead for a week or so now), and when it is plugged in I get the dash lights and a really fast ticking noise, which is exactly what the old starter was doing, and I was pretty certain that meant it was dead.
I'm exhausted from having worked all night last night, then mowing the lawn and arguing with that stupid starter now, so I'm done for the day, but if anyone has any suggestions, there's always tomorrow.
Worst part is, we are having a gorgous long weekend, with weather over 20C and my Jeep isn't running which meanbs no cruising with the top down and no way to get my kayak to the water. :ahhh

Def
-
@Grant Lamontagne said:
and when it is plugged in I get the dash lights and a really fast ticking noise, which is exactly what the old starter was doing, and I was pretty certain that meant it was dead.That sounds like battery couldn't supply enough power, not starter problem. Connect battery to the other car with jumper cable and see if it works.
-
The 12v power system was the extent of my usefulness

Hopefully someone else can help with the high speed ticking diagnosis
-
Thanks for the tip Jie- I hooked the VW up to it and it started. Not easily and not right away, but it started.
Now I'm still getting the Check Gauges light and the battery doodad is still all the way to the 19 side, which is what it was doing the other day just before dying. It's been running for about 20 minutes now and hasn't kicked the bucket yet. Should I just leave it running and the gauge will sort itself out or is this indicative of another problem?
Def
Sent from my MB860 using Tapatalk 2

-
I ran it for about 45 minutes then shut it down. Absolutely nothing happened- no ticking, no attempts to start, nothing. Maybe I just need to leave it running all the time. ::)
Def
-
I know a bit about 12V systems, but nothing about auto-mechanics ... but I can tell you an alternator pumping out 19V is not a good thing :-\
-
Other than the not being able to start it thing and the gauge thing, it seemed fine.
Def
-
High speed ticking from a starter would mean that there is insufficient current from the battery to fully engage the starter.
The instrument cluster appears to be acting as though its processor is not getting enough voltage.
The likely causes are:
-
Either the alternator is not putting out enough current
-
Or the battery has a shorted cell, which is demanding all of the alternator's current
There is also a possibility of a loose connection that is preventing the alternator's output from reaching the rest of the electrical system.
One other possibility is that the powertrain control module is not controlling the alternator's output correctly.
-
-
@Grant Lamontagne said:
Other than the not being able to start it thing and the gauge thing, it seemed fine.Def

Well that's OK then, at least it's nothing to worry about :P

Have you got a multimeter to put across the battery terminals while It's running to see what it is putting out? If it starts off the jump leads from the other car I'd say the next thing is the Jeep battey. I can see that it may have struggled to start off the jump leads if your battery was trying to pull the power in, but 45 minutes should have put some decent charge back in. Try putting a meter across the terminals while it's not running ... ? The old set up might have shafted your battery mate, but don't go forking out for a new one till you know if that's the case or not
@turnsouth said:
High speed ticking from a starter would mean that there is insufficient current from the battery to fully engage the starter.The instrument cluster appears to be acting as though its processor is not getting enough voltage.
The likely causes are:
- Either the alternator is not putting out enough current
- Or the battery has a shorted cell, which is demanding all of the alternator's current
There is also a possibility of a loose connection that is preventing the alternator's output from reaching the rest of the electrical system.
One other possibility is that the powertrain control module is not controlling the alternator's output correctly.
Paul, could this be as simple as an earth fault? Would it be prudent to clean up all the earth connections to ensure there's a full circuit wherever there should be?
-
I'm thinking the faulty alternator or complete discharge may have fried the battery so it's not taking any more charge at all. When everything is off measure the voltage at battery terminals, it should be around 12v. Then start it up (if you still can by boosting with the VW) and measure again, now it should be about 14v. Any lower the alternator isn't charging, and if it's 19v there then the alternator is really smurfed, might want to avoid running the vehicle till you can change the alternator, I don't know what voltage the CPU can take before frying.
The battery is also probably dead, so take it to any place that sells them and do a load test, it's a hand held thingy and takes 30 seconds to do.
-
@jzmtl said:
I'm thinking the faulty alternator or complete discharge may have fried the battery so it's not taking any more charge at all. When everything is off measure the voltage at battery terminals, it should be around 12v. Then start it up (if you still can by boosting with the VW) and measure again, now it should be about 14v. Any lower the alternator isn't charging, and if it's 19v there then the alternator is really smurfed, might want to avoid running the vehicle till you can change the alternator, I don't know what voltage the CPU can take before frying.The battery is also probably dead, so take it to any place that sells them and do a load test, it's a hand held thingy and takes 30 seconds to do.
Good call

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login