And so it begins.... (My adventures into Alox!)
-
Yep good tips for sure. I did 1 and 2 in your list and learned. If the pivots dont get inside the scales you end up with a sad floppy SAK with no snap at all. I still use hart burs for removing pins and havent had any issue wrecking scales since I moved to using those.
I never had an off center hold in a spring though, but thats why I dont recommend people use a milling bit to drill with. I like a pointed self centering bit and not clamping the work so its free to self center as I drill. ;)
-
Are the Phillips drivers on the Lite models (e.g. Spartan Lite) the same as the ones on Explorers? I found a Spartan Lite on eBay with incredibly ugly scales. I hope this will stay low on the bidding count. :D
Are Phillips drivers working well with stock caplifter/can opener springs? Do they need grinding? How about the mid-position lock?
-
The lite models should all have the modern philips (i think) which is the on you want. The older style (that is paired with old mag glass on explorers) is not what you want, it wont fit without moving the pivot and lots of heavy modding.
The philips is too wide for an opener layer spring, so you can do what I did and use a blade layer spring, or thin down the philips to work with the opener layer spring but then I don't think that layer would fit against a scale, youd have to put in near the middle, which probably would work better anyhow. The best way to explain how to shape the pivot part to fit, is.. whatever spring you end up using, shape it to match whatever part normally goes with that spring. So if you replace the can opener for a philips, match the shape of the can opener pivot area. Scribe and grind and sand and polish. Thats it! :D
-
I have a spartan lite and it is the small inline :)
-
Blade spring from a non-Solo knife, I guess.
Mh... blade springs are the least expendables. :-X
Let's see. :) -
@crackout said:
Blade spring from a non-Solo knife, I guess.
Mh... blade springs are the least expendables. :-X
Let's see. :)Exactly.. and then you think man I have to waste a pioneer just for the spring... think a few more moves ahead in this chess game and you'll arrive where I did... it makes sense to make up springs. :D
-
So you grind down your custom scissors springs or do you have an extra design?
You could still get these one layer Pioneers (the Pioneer Pruner is actually still being produced) and use the blade as a replacement (pivot assembly assumed).
-
@crackout said:
So you grind down your custom scissors springs or do you have an extra design?You could still get these one layer Pioneers (the Pioneer Pruner is actually still being produced) and use the blade as a replacement (pivot assembly assumed).
Yup I made my custom spring to have extra metal so I can grind down to use how I need it.
Pruner would work great. I thought it was discontinued too though along with solo/rancher/harvester.
I loved this SAK but it was a for hire job so it's long gone... I need to make another for myself.



-
So both retain their mod position snap in this example? And also with a blade spring?
Both the Solo and the Pruner are still listed on the site. Not sure if that's a 'yes' for still part of the line-up though. I can still order them both at Amazon no problem.
-
Finally got this sucker done... urban pioneer jr! Pioneer Cadet with scissors...

Red hard anodize with brass liners. The keyring had to go to make room for the awl and I made a custom piece in brass to take it's place.



Here is what the awl modification looks like.



-
Uah...that looks like a lot of work.
-

I wish I had some money to spend :( This thing looks just dreamy.

-
That is EXACTLY what I want. Love the awl.
:ahhh

-
I have to keep a close eye on you. Is the knife in your profile a mod? If so could we see a bigger picture. Also any progress on the backtool 84mm? After seeing the Mini Pioneer I can't wait to see what you do with that. A Mini Camper with the corkscrew or Hiker with the screwdriver.
-
@nj2656 said:
I have to keep a close eye on you. Is the knife in your profile a mod? If so could we see a bigger picture. Also any progress on the backtool 84mm? After seeing the Mini Pioneer I can't wait to see what you do with that. A Mini Camper with the corkscrew or Hiker with the screwdriver.lol, thats the one I did a few pages back with the electricians blade and combo tool.
Im working on the backtool mod next.

-
Im working on the backtool mod next.

Can't wait for that.
Anyone tried fitting a nailfile on a 93mm? Are there even bigger files than the ones from Cadets?
Lots have tried that. It sits too low in the knife for the nail nick to be used. I had a idea for tools like that to fit but it's very time consuming and costly.
-
Im working on the backtool mod next.

Can't wait for that.
Anyone tried fitting a nailfile on a 93mm? Are there even bigger files than the ones from Cadets?
Lots have tried that. It sits too low in the knife for the nail nick to be used. I had a idea for tools like that to fit but it's very time consuming and costly.
Ya the only way I can think to make use of the 84mm parts on 93 would be to make a custom spring with fatter ends to hold the tools up higher.
-
I was thinking of making a very small carrier that would be the same size as a 91mm tool. I don't have anything to draw up one though so the thought is still in my head :(
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login