MT.O Prybar
-
At the last UK meet up i was talking to sparky415 about prybars and he put forward a number of interesting and original ideas and suggestions on the subject.
After finally getting round to printing my prybar i contacted Sparky again about his ideas and the possibility of putting together a printed prototype.
With his design input i set about putting together a simple yet useful prybar based around improving the original widgy bar.This is what we came up:

Including the MT.O logo with the O has a useable 1/4" hex driver was Sparky's great idea, but as he pointed out could be a source of contention.
I contacted Grant and Travis to make sure it was ok and not only did they like it but gave some design input aswell, so here it is, the Official MT.O Prybar.
This single-piece tool can be used as a prybar and nail lifting tool, but also has a range of metric hex drivers (2.5, 3.2, 4, 5, 5.5 and 7mm), a bottle opener and a 1/4" hex bit driver.
An o-ring can be installed in the tail to help secure a hex bit (8mm ID, 2.5mm section).
The prybar can be secured to a keychain or lanyard with a No.2 McGizmo clip or similar 25mm gate clip through the 1/4" hex hole or with a small split ring through the MT.O dot.Due to future manufacturing considerations i have designed this tool with two different thicknesses: 3mm and 5mm. The first picture shows the thinner tool and the second picture shows the thicker version.

Both these models are up on shapeways, just search for 'MT.O Prybar' or click here (3mm) or here (5mm)
As this is a community project, no commission has been added to the price but they're still expensive so i plan to have a number ofthese tools cut from high grade stainless blade steel in the near future.In the mean time i've ordered a prototype from shapeways and when it arrives and is proven to meet requirements i'll start a pass-around thread for it.
Please feel free to leave any suggestions and/or feedback, both positive and negative.
-
I'm impressed. I particularly like the 5mm version - I like thicker OPMTs more than the thinner tools - but both versions seem to be well thought through with a good number of functions and what seems to be carefully considered ergonomics. I think this one that I will get round to ordering.
-
One of each for me!

I think I may be the first order in!

-
BTW, I LOVE how the wrench is designed. Very clever.

-
:)
-
BEAUTIFUL
JR -
Great work guys..

-
Very nice. Question - presumably shape ways dont heat temper etc. Is this a problem or is it just man enough regardless due to the thickness?
Sent from my HTC One X using Tapatalk 2
-
Awesome!
Big question:How much?
Aw,never mind,I'll have one!!
-
I like the design! The waterjet service I use is $1 a part for cutting which is cheap, but I dont know if it is 'precise' enough to cut that out or not. I've got some Ti being cut soon by him so we'll see how close it matches the file.
-

Sadly very little of this great looking Pry-Bar is anything to do with me
Great job Mate

-
That's really nice.

Just an idea: would it be possible to make the two small cutouts around the 1/4 hex hole, square and wide enough to work on 14-15 gauge spokes? Since they're there, I don't see why not adding some bike-friendly functionality to this otherwise
tool. :) -
@kitbeard said:
I'm impressed. I particularly like the 5mm version - I like thicker OPMTs more than the thinner tools - but both versions seem to be well thought through with a good number of functions and what seems to be carefully considered ergonomics. I think this one that I will get round to ordering.Thanks kitbeard, i suspect there will be a few small changes made to this tool after actually trying it out but i did my best to make it as useable as possible during the design stage.
@Mr. Whippy said:
One of each for me!
I think I may be the first order in!
@Mr. Whippy said:
BTW, I LOVE how the wrench is designed. Very clever.
Thanks Mr. Whippy, your right, the first and so far only taker. Please give them a thorough testing when they arrive, i'm intrigued as to how functional you will find them.
I'm glad you recognised the advantage of the 15 degree slant on the 1/4" hex, hopefully it will come in handy.@MadPlumbarian said:
BEAUTIFUL
JRThanks alot, i'm a bit unsure as to why there haven't been more community multi-tool projects but i suppose we've had more than our fair share of input into many of the big manufacture's tools anyway.
@landwomble said:
Very nice. Question - presumably shape ways dont heat temper etc. Is this a problem or is it just man enough regardless due to the thickness?The stainless steel parts are heated to quite a high temperature to sinter them while also being infused with bronze. I have heard that the stainless steel grade is similar to 420 so it should be temperable. I've tried drilling it and it's certainly harder than mild steel but exactly how hard i couldn't stay.
It's true that at 5mm it should be impossible to break it without a bench vise and a big hammer however tempered it is.@kirk13 said:
Awesome!
Big question:How much?
Aw,never mind,I'll have one!!3mm- just over £21
5mm- just under £30
Well at least they're cheaper than an atwood.@Syph007 said:
I like the design! The waterjet service I use is $1 a part for cutting which is cheap, but I dont know if it is 'precise' enough to cut that out or not. I've got some Ti being cut soon by him so we'll see how close it matches the file.Cheers, and thanks for the info, water-jet accuracy can range from .5 to .1mm depending on the machine and getting straight sides requires the cutting nozzle to change it's angle as it cuts which some don't do.
Please let me know what you descover as $1 sounds pretty good to me.@sparky415 said:

Sadly very little of this great looking Pry-Bar is anything to do with me
Great job Mate
Both the bottle opener's dimensions and angle of attack as well as using the MT.O text as a functional part of the design were your ideas, everything else was just filling in the gaps.
Soon you'll be able to do a back to back test between mine and your bottle openers to see which is best.@Nikos said:
That's really nice.
Just an idea: would it be possible to make the two small cutouts around the 1/4 hex hole, square and wide enough to work on 14-15 gauge spokes? Since they're there, I don't see why not adding some bike-friendly functionality to this otherwise
tool. :)Thats an interesting suggestion, i'll draw it up see if it's doable. If not then perhaps a bike dedicated tool might need thinking about.
-
You need any electrical work doing Mate? >:D
Guess I better start saving my pennies :ahhh

-
If you do one with the spoke wrench I will be getting one.

-
My Tofty MTO prybars arrived today.

I haven't tried the wrenches yet, but the prytip and bottle opener work extremely well. The wrenches are fairly small, so I'll have to find some smaller bolts to test them on. The one thing to note is the finish. It is fairly industrial. There are no sharp edges or abrasive surfaces but the finish is uneven, I think is the best way to put it. Function is fine however. Here are some pictures.

The bottle opener is excellent. Really good leverage.
Here is a shot with the Pockettool X (now Leatherman) Piranha, Atwood Roid Rench Prybaby and the two MTO prybars:

Thickness of the tools PTX Piranha, Atwood Roid Rench, 5mm MTO then 3mm MTO

Here is a shot trying to show the finish of the tools:

I think these are very functional one pieces. I love the MTO logo (with 1/4 bit driver). The finish is fairly industrial especially when compared to an Atwood, PTX Piranha or PocketWrench II. However, given the size and functionality of the tool, it's pretty minor (except for those looking for tool art pieces rather than handy one piece tools).
Great job Tofty!

-
Those look great!
Does the finish seem like it might invite corrosion problems? What kind of steel was used?
Def
-
Nice pictures Mr W

Great job Tofty

Those look sooooo cool

-
Not totally sure (I think Shapeways discusses it) but I believe it's a stainless steel with some sort of epoxy(?) binder. I don't think corrosion is going to be a major problem.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login