MT.O Prybar
-
I like the design! The waterjet service I use is $1 a part for cutting which is cheap, but I dont know if it is 'precise' enough to cut that out or not. I've got some Ti being cut soon by him so we'll see how close it matches the file.
-

Sadly very little of this great looking Pry-Bar is anything to do with me
Great job Mate

-
That's really nice.

Just an idea: would it be possible to make the two small cutouts around the 1/4 hex hole, square and wide enough to work on 14-15 gauge spokes? Since they're there, I don't see why not adding some bike-friendly functionality to this otherwise
tool. :) -
@kitbeard said:
I'm impressed. I particularly like the 5mm version - I like thicker OPMTs more than the thinner tools - but both versions seem to be well thought through with a good number of functions and what seems to be carefully considered ergonomics. I think this one that I will get round to ordering.Thanks kitbeard, i suspect there will be a few small changes made to this tool after actually trying it out but i did my best to make it as useable as possible during the design stage.
@Mr. Whippy said:
One of each for me!
I think I may be the first order in!
@Mr. Whippy said:
BTW, I LOVE how the wrench is designed. Very clever.
Thanks Mr. Whippy, your right, the first and so far only taker. Please give them a thorough testing when they arrive, i'm intrigued as to how functional you will find them.
I'm glad you recognised the advantage of the 15 degree slant on the 1/4" hex, hopefully it will come in handy.@MadPlumbarian said:
BEAUTIFUL
JRThanks alot, i'm a bit unsure as to why there haven't been more community multi-tool projects but i suppose we've had more than our fair share of input into many of the big manufacture's tools anyway.
@landwomble said:
Very nice. Question - presumably shape ways dont heat temper etc. Is this a problem or is it just man enough regardless due to the thickness?The stainless steel parts are heated to quite a high temperature to sinter them while also being infused with bronze. I have heard that the stainless steel grade is similar to 420 so it should be temperable. I've tried drilling it and it's certainly harder than mild steel but exactly how hard i couldn't stay.
It's true that at 5mm it should be impossible to break it without a bench vise and a big hammer however tempered it is.@kirk13 said:
Awesome!
Big question:How much?
Aw,never mind,I'll have one!!3mm- just over £21
5mm- just under £30
Well at least they're cheaper than an atwood.@Syph007 said:
I like the design! The waterjet service I use is $1 a part for cutting which is cheap, but I dont know if it is 'precise' enough to cut that out or not. I've got some Ti being cut soon by him so we'll see how close it matches the file.Cheers, and thanks for the info, water-jet accuracy can range from .5 to .1mm depending on the machine and getting straight sides requires the cutting nozzle to change it's angle as it cuts which some don't do.
Please let me know what you descover as $1 sounds pretty good to me.@sparky415 said:

Sadly very little of this great looking Pry-Bar is anything to do with me
Great job Mate
Both the bottle opener's dimensions and angle of attack as well as using the MT.O text as a functional part of the design were your ideas, everything else was just filling in the gaps.
Soon you'll be able to do a back to back test between mine and your bottle openers to see which is best.@Nikos said:
That's really nice.
Just an idea: would it be possible to make the two small cutouts around the 1/4 hex hole, square and wide enough to work on 14-15 gauge spokes? Since they're there, I don't see why not adding some bike-friendly functionality to this otherwise
tool. :)Thats an interesting suggestion, i'll draw it up see if it's doable. If not then perhaps a bike dedicated tool might need thinking about.
-
You need any electrical work doing Mate? >:D
Guess I better start saving my pennies :ahhh

-
If you do one with the spoke wrench I will be getting one.

-
My Tofty MTO prybars arrived today.

I haven't tried the wrenches yet, but the prytip and bottle opener work extremely well. The wrenches are fairly small, so I'll have to find some smaller bolts to test them on. The one thing to note is the finish. It is fairly industrial. There are no sharp edges or abrasive surfaces but the finish is uneven, I think is the best way to put it. Function is fine however. Here are some pictures.

The bottle opener is excellent. Really good leverage.
Here is a shot with the Pockettool X (now Leatherman) Piranha, Atwood Roid Rench Prybaby and the two MTO prybars:

Thickness of the tools PTX Piranha, Atwood Roid Rench, 5mm MTO then 3mm MTO

Here is a shot trying to show the finish of the tools:

I think these are very functional one pieces. I love the MTO logo (with 1/4 bit driver). The finish is fairly industrial especially when compared to an Atwood, PTX Piranha or PocketWrench II. However, given the size and functionality of the tool, it's pretty minor (except for those looking for tool art pieces rather than handy one piece tools).
Great job Tofty!

-
Those look great!
Does the finish seem like it might invite corrosion problems? What kind of steel was used?
Def
-
Nice pictures Mr W

Great job Tofty

Those look sooooo cool

-
Not totally sure (I think Shapeways discusses it) but I believe it's a stainless steel with some sort of epoxy(?) binder. I don't think corrosion is going to be a major problem.
-
@Mr. Whippy said:
Not totally sure (I think Shapeways discusses it) but I believe it's a stainless steel with some sort of epoxy(?) binder. I don't think corrosion is going to be a major problem.Well at least you'll not suffer the issues you suffered with the slickness of the Spirit out on the farm :D I'm not a one piece tool guy myself, but they do look cool 8)

-
From http://www.shapeways.com/materials/steel
*Shapeways 3D printed stainless steel is very strong and rigid with similar properties to 420 stainless steel, except it is infused with a bronze content of up to 30%. This gives some Stainless Steel objects a slightly bronze hue.
We deposit small drops of glue onto layers of stainless steel powder. Then a new layer of powder is spread and the process repeats until we have a fully printed tray. Then we take the printed objects out carefully. In this stage of the process, the objects are very fragile–similar to wet sand. After, we sprue the objects together and infuse them with bronze. Items closer to the bronze infusion start point will absorb more bronze. These items might look more golden than other items. We are working on standardizing the colors, but in the meanwhile, there will be some color differences in the models you may receive (see picture above). Then, we cut off the objects from the tree and polish them with a tumbler. Depending on how fragile the printed objects are we use different polishing media. This is why some objects may have a slightly shinier surface than others. After polishing,we spray on a sealant and ship to your doorstep.
This material is watertight, is dishwasher safe, not recyclable, and not foodsafe. It is heatproof to 831C/1528F degrees. Higher temperatures may significantly change material properties.*
So, it's basically steel grains welded together with bronze. I assume it would be very corrosion resistant, especially since they say it's dishwasher safe.
-
Thanks Mr. Whippy, nice write-up, glad to hear your first impressions were generally positive.
The upcoming production run should have a much better finish anyway.Mine arrived a couple of days ago:






The bottle opener has to be my favourite part as it's so much better than my other prybar.
All the hex cut-outs seem to be the right size although i can't test the smallest ones as i don't have anything suitable.@sparky415 said:
You need any electrical work doing Mate? >:D
Guess I better start saving my pennies :ahhh

Just keep an eye out for the soon to be created pass-around thread.
@stealth007s said:
If you do one with the spoke wrench I will be getting one.I had a look at adding a spoke wrench but there wasn't enough room for it anyhere sensible so i'll have a go at a bike tool soon.
@Grant Lamontagne said:
Those look great!
Does the finish seem like it might invite corrosion problems? What kind of steel was used?
Defit kinda looks like it would especially inside the lettering? JR
@50ft-trad said:
@Mr. Whippy said:
Not totally sure (I think Shapeways discusses it) but I believe it's a stainless steel with some sort of epoxy(?) binder. I don't think corrosion is going to be a major problem.
Well at least you'll not suffer the issues you suffered with the slickness of the Spirit out on the farm :D I'm not a one piece tool guy myself, but they do look cool 8)

Thanks Everyone and thanks Steinar for posting that info.
I've been carrying my first prybar on my keychain for a month or so now and haven't seen any signs of corrosion on the tool, although the hex bits gone rusty already. -
If you do one with the spoke wrench I will be getting one.
I had a look at adding a spoke wrench but there wasn't enough room for it anyhere sensible so i'll have a go at a bike tool soon.
What's wrong with making the cut-outs around the O in MT.O the right size/shape for spokes? It's not like they won't be able to hold the o-ring if they're square, right?
-
@Tofty said:
Thanks Mr. Whippy, nice write-up, glad to hear your first impressions were generally positive.
The upcoming production run should have a much better finish anyway.Mine arrived a couple of days ago:


Thanks Everyone and thanks Steinar for posting that info.
I've been carrying my first prybar on my keychain for a month or so now and haven't seen any signs of corrosion on the tool, although the hex bits gone rusty already.I really like the finish! kinda gives it that, not brand new, first deverginizing it, used, but kept in very good condition! and yeah you can see the rust forming on the bit, only problem with that is it will transfer to the tool with no hesitation! can the bit store horizontal in the wrench area? JR
-
If you do one with the spoke wrench I will be getting one.
I had a look at adding a spoke wrench but there wasn't enough room for it anyhere sensible so i'll have a go at a bike tool soon.
What's wrong with making the cut-outs around the O in MT.O the right size/shape for spokes? It's not like they won't be able to hold the o-ring if they're square, right?
There just doesn't seem to be enough room for them while maintaining the necessary material thickness around the 1/4" hex.

@MadPlumbarian said:
I really like the finish! kinda gives it that, not brand new, first deverginizing it, used, but kept in very good condition! and yeah you can see the rust forming on the bit, only problem with that is it will transfer to the tool with no hesitation! can the bit store horizontal in the wrench area? JRI have a bad habit of not wanting to use shiny new tools so this is the perfect solution; make them look ragged to begin with.
There are a number of hex bits on the market that wouldn't suffer this fate; from TiN coated to being completely made from stainless steel, in fact thats what will be accompanying my prybar during the pass-around.

A lovely Wera stainless PH2 bit.
Unfortunately a hex bit can't be stored in the wrench cutout on the MT.O prybar, thats what the little bit kit you get with forum membership is for. I wish there was room but as shown above sometimes there just isn't.
-
Dear Santa......

-
@sparky415 said:
Dear Santa......Yes, dear??
-
Are you really sure it's rust and not just the bronze starting to acquire color? We are talking about 420 type steel and bronze, I have a hard time believing it should rust easily.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login