Skip to content
  • Categories
  • Recent
  • Popular
  • World
Skins
  • Light
  • Dark

Collapse

NodeBB

Wenger Scissors and Saw into Vic 84mm frame. Pic HEAVY.

Scheduled Pinned Locked Moved The Mod Squad
43 Posts 1 Posters 21.9k Views
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • PTRSAKP
    PTRSAKP
    PTRSAK
    wrote on last edited by
    #11

    more pic's of the fitting together

    There is a little bit of clearance on the sides of the spacer in the scissors layer, but it's 0.4mm spread over the two sides... It really is negligible. I guess I could hunt out an old thick tang main blade, or make a custom spacer from aluminium, but this works and it's easy to do. I'm planning to EDC this knife for a while as a bit of a road test ,so we'll see how it holds up.

    The spring tension holds the parts in place without them rattling around, no different to the oversize hole in the locking Wenger screwdriver. The difference in size in very small and in fact it probably helps things line up.

    Thanks for the props everyone. I'm really just doing this stuff for fun and having nice people say nice things about it makes it all the more enjoyable.

    1 Reply Last reply
    0
    • crackoutC
      crackoutC
      crackout
      wrote on last edited by
      #12

      Are the springs flush with the liners once the tool is exposed?

      1 Reply Last reply
      0
      • PTRSAKP
        PTRSAKP
        PTRSAK
        wrote on last edited by
        #13

        As assembled the two recruit springs sit about 1mm proud in both open and closed position for both scissors and saw.
        This could be tidied up with a little light grinding on the pad of the working end of the spring. I guess I'm a bit of a 90% kind of guy. I tend to get distracted by the next :gimme:shiny thing before I get the last of the fine tuning and polishing finished.

        1 Reply Last reply
        0
        • papercutP
          papercutP
          papercut
          wrote on last edited by
          #14

          Now that I have acquired pretty much all the donors I need for my 3 potential mods- farmer plus scissors, mini farmer plus scissors, and one more secret mod, I think I'll heap even more praise on ya! Great job man! After years of folks complaining about the scissors and limited saws on 84mm, the (perhaps all too obvious) solution has been found. Maybe the folks at Vic have been secretly chuckling about our ineptitude-in a Swiss accent "it fits right in, can't you see?!?"

          If anyone has a waterjet, I'd prob go in on a couple sets of precut 84mm CF scales if a group order was put in.

          Cheers

          1 Reply Last reply
          0
          • MadPlumbarianM
            MadPlumbarianM
            MadPlumbarian
            wrote on last edited by
            #15

            Very nice job :tu: JR

            1 Reply Last reply
            0
            • papercutP
              papercutP
              papercut
              wrote on last edited by
              #16

              @Syph007 said:
              Bravo! Great to know the scissors can be moved there. :salute:

              I do like the Wenger scissors, it's just the bobbing up and down part as you cut that kept me from loving them.

              But.. now there is a possible solution if you took two backsprings of half thickness, one for the scissors spring action and one to keep them open. Ive wanted to do that mod for awhile, but now you've shown I can do that mod AND keep it on a Vic. So... Someday I gotta try that. The list of cool things to try is getting to long though. 😄

              Keep up the great modding work, and I look forward to you next trick!

              How would you get two half thickness backsprings? Grind down two springs or are there half tickness springs available?

              1 Reply Last reply
              0
              • Syph007S
                Syph007S
                Syph007
                Global Moderators
                wrote on last edited by
                #17

                @papercut said:

                @Syph007 said:

                Bravo! Great to know the scissors can be moved there. :salute:

                I do like the Wenger scissors, it's just the bobbing up and down part as you cut that kept me from loving them.

                But.. now there is a possible solution if you took two backsprings of half thickness, one for the scissors spring action and one to keep them open. Ive wanted to do that mod for awhile, but now you've shown I can do that mod AND keep it on a Vic. So... Someday I gotta try that. The list of cool things to try is getting to long though. 😄

                Keep up the great modding work, and I look forward to you next trick!

                How would you get two half thickness backsprings? Grind down two springs or are there half tickness springs available?

                Yep grinding down thicker ones.

                1 Reply Last reply
                0
                • papercutP
                  papercutP
                  papercut
                  wrote on last edited by
                  #18

                  Aren't the Wenger pivots a touch wider than 84mm vics (2.5mm rather than 2.2mm)? Is that even enough to make a difference if the pinning is done correctly? Or would the spring give enough pressure to even things out?

                  1 Reply Last reply
                  0
                  • PTRSAKP
                    PTRSAKP
                    PTRSAK
                    wrote on last edited by
                    #19

                    How about this for a logo for these hybrid SAKs

                    1 Reply Last reply
                    0
                    • papercutP
                      papercutP
                      papercut
                      wrote on last edited by
                      #20

                      It looks like the CF is quite smooth. Does the sak feel slippery in your hands?

                      Cheers

                      1 Reply Last reply
                      0
                      • PTRSAKP
                        PTRSAKP
                        PTRSAK
                        wrote on last edited by
                        #21

                        I've just done a hands on side-by-side comparison with a pair of new condition Vic' cellidor scales and the CF is a little more grippy than unworn standard scales.

                        Kind of like the difference between running your finger along Perspex (acrylic) and Lexan (polycarbonate). they are both smooth, but your finger glides along one and drags a little on the other.

                        1 Reply Last reply
                        0
                        • W
                          W
                          WiSAKfan
                          wrote on last edited by
                          #22

                          did you ever try the wenger file in place of the vic file?

                          thanks.

                          1 Reply Last reply
                          0
                          • PTRSAKP
                            PTRSAKP
                            PTRSAK
                            wrote on last edited by
                            #23

                            @WiSAKfan said:
                            did you ever try the wenger file in place of the vic file?

                            thanks.

                            Only got one Wenger with a file and that's a toolchest and I don't want to pull it apart. But it should fit just the same as the saw.

                            1 Reply Last reply
                            0
                            • W
                              W
                              WiSAKfan
                              wrote on last edited by
                              #24

                              thank you.

                              and thank you for this thread. I will be attempting this when work slows down a little.

                              have the donor knives, just need to sand down some pin stock

                              I'll be attempting to make an awl/file combo like i saw a modder do

                              probably try it on the wenger file first just in case something goes wrong.

                              1 Reply Last reply
                              0
                              • PTRSAKP
                                PTRSAKP
                                PTRSAK
                                wrote on last edited by
                                #25

                                ah, I thought you meant the big metalsaw/file...if you are meaning the nail-file in place of the small blade, yes I have fitted then to Vic' knives. they need a very slight amount of material removed from the back end of the tang where the blade sits in the closed position to make the blade sit a little higher so the nail nick is accessible.
                                Go very slowly with a fine stone and check often, it only takes a fraction of a mm at the back of the tang to lift the tip of the blade several mm.

                                1 Reply Last reply
                                0
                                • papercutP
                                  papercutP
                                  papercut
                                  wrote on last edited by
                                  #26

                                  Still super inspiring mod. How is it doing as an EDC?

                                  1 Reply Last reply
                                  0
                                  • Outback in IdahoO
                                    Outback in IdahoO
                                    Outback in Idaho
                                    wrote on last edited by
                                    #27

                                    Looks rather spiffy. When you taking orders? 😄

                                    1 Reply Last reply
                                    0
                                    • PTRSAKP
                                      PTRSAKP
                                      PTRSAK
                                      wrote on last edited by
                                      #28

                                      The carbon seems to be standing up to use very well. The only "problem" with this knife is that the saw I used is very blunt and almost useless. It didn't worry me at the time as it was a prototype "proof of concept" build but now I might have to try and sharpen it up with my jewelers files.

                                      I just recently bought a sheet of the 1mm carbon and I might pull this apart and do carbon liners for it too.

                                      1 Reply Last reply
                                      0
                                      • J
                                        J
                                        Jake
                                        wrote on last edited by Jake
                                        #29

                                        Thanks for this guide. Since I couldn't bring myself to break apart a 84mm Golfer to get the scissors layer, I decided to try this Wenger method instead.

                                        I think the effort was pretty successful. I give you the Faux-Voyageur:

                                        I made custom 2.25mm pivots by grinding down some brass rod to 2.25mm and then drilling and tapping for a 0-80 screw. I used 3/16" flat head 0-80 stainless screws. My pivots were a little too long-- originally I made them 7.25mm long but when I do this again, I'll make them 7mm or a little less.

                                        Instead of grinding other tools down to make the rest for the scissors, I milled a custom one from aluminum. I also modeled the scale and liner in STL format. They're derived from scanning on a flatbed scanner, so they're not perfect-- but they're decent. I deburred and filed a little to get the fit that I wanted, but it didn't take much.

                                        I posted these STLs to github in case they will come in handy to someone else: https://github.com/jake-b/84mm-Victorinox

                                        The only issue is that the pad of the original victorinox back spring is a little too big by 0.5mm-0.7mm or so. Hence, the back spring sticks out just a tad when closed. I don't really know how to solve this yet-- I guess the face of the back spring needs to be ground down but I don't know how that will affect "snap" and I don't think doing it by hand with a bench grinder is a good idea. Also I added an extra 0.1mm brass washer in between the scissors and the scale, and I don't think its necessary, so next time its apart, I'm going to take it out as it makes the end a little to thick. Both problems are not terrible, so I'm going to start carrying the knife anyway.

                                        Anyhow, thanks to everyone on this forum for giving me the ambition to try this modding thing for myself-- and to all the individual authors for posting great pictures and how-to's.

                                        I still like the Victorinox scissors better, so I might try the 91mm-in-an-84mm mod next. I'll still need some 84mm scissors broken out to use as a template I think. While the "micro-serrated" Wenger scissors are cool, I like that both halves of the Victorinox scissors don't move when being operated.

                                        1 Reply Last reply
                                        0
                                        • PTRSAKP
                                          PTRSAKP
                                          PTRSAK
                                          wrote on last edited by
                                          #30

                                          Nice work. and welcome to the forum

                                          The CAD models could be useful too.

                                          As far as the spring goes, you can file the back (outside) of the spring at the end there without it effecting the snap very much at all.
                                          I would stay away from filing the inside as it will effect snap and possibly the open/closed position of the scissors.

                                          1 Reply Last reply
                                          0

                                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                          With your input, this post could be even better 💗

                                          Register Login

                                          • Login

                                          • Don't have an account? Register

                                          • First post
                                            Last post
                                          0
                                          • Categories
                                          • Recent
                                          • Popular
                                          • World