Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Show off your Sak mod's!

Scheduled Pinned Locked Moved The Mod Squad
6.3k Posts 1 Posters 1.2m Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Show off your Sak mod's!
Show off your Sak mod's!
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • KTesh Offline
    KTesh
    Posts: 114
    KTesh Offline
    KTesh
    wrote on last edited by
    #2445 Quote Reply

      Please forgive this cross post... I didn't discover this subforum until after I posted in the Swiss forum.

      Rather than wait for my "Plus" scales to arrive, I decided to mod my older (damaged) Ranger's scale to see if I could add the pen slot myself. I figure that if I messed it up, I could go ahead and get a replacement scale from Victorinox when I send it in.

      A previous attempt to remove the scale (due to a large gap between the scale and the body plate) damaged the scale, so I've used poster putty (old and nasty as it was) to help hold the scale to the knife. I fixed the gap by boiling water, then putting the scale in for a few minutes, then bending it the opposite direction of the old bend, and "set" it by rinsing in cold water.

      After removing the scale for the mod, I used hobby files, and a Xacto knife to cut the grove needed for the pen. It took a lot of test fits (is the "Plus" scale thicker than the original scale?) to get the scale to fit "flush" with the body. The scale is now very thin where the slot is.

      Pleased with the results, I swapped the scale of my newer Ranger model knife. Even though the results aren't as clean as a factory made one, I think that it is suitable for weapons load testing (read "good enough for government work")(sorry, I was a 462 in the USAF (RAF Upper Heyford UK, '88-'90)).

      Weapons!
      K'Tesh

      1 Reply Last reply
      • stealth007s Offline
        stealth007s
        Posts: 6,181
        stealth007s Offline
        stealth007s
        wrote on last edited by
        #2446 Quote Reply

          @KTesh said:
          Please forgive this cross post... I didn't discover this subforum until after I posted in the Swiss forum.

          Rather than wait for my "Plus" scales to arrive, I decided to mod my older (damaged) Ranger's scale to see if I could add the pen slot myself. I figure that if I messed it up, I could go ahead and get a replacement scale from Victorinox when I send it in.

          A previous attempt to remove the scale (due to a large gap between the scale and the body plate) damaged the scale, so I've used poster putty (old and nasty as it was) to help hold the scale to the knife. I fixed the gap by boiling water, then putting the scale in for a few minutes, then bending it the opposite direction of the old bend, and "set" it by rinsing in cold water.

          After removing the scale for the mod, I used hobby files, and a Xacto knife to cut the grove needed for the pen. It took a lot of test fits (is the "Plus" scale thicker than the original scale?) to get the scale to fit "flush" with the body. The scale is now very thin where the slot is.

          Pleased with the results, I swapped the scale of my newer Ranger model knife. Even though the results aren't as clean as a factory made one, I think that it is suitable for weapons load testing (read "good enough for government work")(sorry, I was a 462 in the USAF (RAF Upper Heyford UK, '88-'90)).

          Weapons!
          K'Tesh

          Looks like that worked well for you K'Tesh. Very nice!¡!

          1 Reply Last reply
          • PTRSAK Offline
            PTRSAK
            Posts: 4,776
            PTRSAK Offline
            PTRSAK
            wrote on last edited by
            #2447 Quote Reply

              @PTRSAK said:
              still a work in progress... The Aloxplorer

              Progressed to completion

              Standard explorer for comparison



              1 Reply Last reply
              • tattoosteve99 Offline
                tattoosteve99
                Posts: 6,326
                tattoosteve99 Offline
                tattoosteve99
                wrote on last edited by
                #2448 Quote Reply

                  @PTRSAK said:

                  @PTRSAK said:

                  still a work in progress... The Aloxplorer

                  Progressed to completion

                  Standard explorer for comparison



                  That's lovely :tu: Now all you need to do is anodize it :).

                  1 Reply Last reply
                  • nuphoria Offline
                    nuphoria
                    Admin Team
                    Posts: 15,038
                    nuphoria Offline
                    nuphoria
                    Admin Team
                    wrote on last edited by
                    #2449 Quote Reply

                      Rather nice... did you decide if the scales could be made thinner or not?

                      1 Reply Last reply
                      • papercut Offline
                        papercut
                        Posts: 1,252
                        papercut Offline
                        papercut
                        wrote on last edited by
                        #2450 Quote Reply

                          It looks like he thinned them down a bit.

                          1 Reply Last reply
                          • PTRSAK Offline
                            PTRSAK
                            Posts: 4,776
                            PTRSAK Offline
                            PTRSAK
                            wrote on last edited by
                            #2451 Quote Reply

                              Yes, I did thin both scales down, took them down to 3mm which looks much better. That is the thickness of most of the slices I cut from the 3/4 plate. This was made from the first couple I cut at 4mm before I decided it was too thick. But it worked out well for prototyping as it gave me some extra material in case I made a complete dog's breakfast of the grooves.

                              I also rounded the ends and continues the grooves around the curve, I really like the way that looks, and with the highly polished surface it kinda looks like a SAK that Agent K would carry. J would have to have something "New & Hot".. maybe one in CF.

                              Guess if this one finds its way onto eBay it will be described as a Men in Black styled Swiss Army Knife. :)

                              1 Reply Last reply
                              • nuphoria Offline
                                nuphoria
                                Admin Team
                                Posts: 15,038
                                nuphoria Offline
                                nuphoria
                                Admin Team
                                wrote on last edited by
                                #2452 Quote Reply

                                  Yes, I can see that! The rounded ends look fabulous :D

                                  1 Reply Last reply
                                  • lowtech Offline
                                    lowtech
                                    Posts: 4,799
                                    lowtech Offline
                                    lowtech
                                    wrote on last edited by lowtech
                                    #2453 Quote Reply

                                      I like the ribbed aluminium scales!
                                      Reminds me of Rimowa Suitcases or an Airstream Trailer somehow.

                                      1 Reply Last reply
                                      • Steinar Offline
                                        Steinar
                                        Posts: 3,435
                                        Steinar Offline
                                        Steinar
                                        wrote on last edited by
                                        #2454 Quote Reply

                                          @lowtech said:
                                          I like the ribbed aluminium scales!
                                          Reminds me of Rimowa Suitcases or an Airstream Trailer somehow.

                                          That was my thought as well. Awesome knife.

                                          1 Reply Last reply
                                          • PTRSAK Offline
                                            PTRSAK
                                            Posts: 4,776
                                            PTRSAK Offline
                                            PTRSAK
                                            wrote on last edited by
                                            #2455 Quote Reply

                                              Actually the Airstream thing did occur to me too, but I couldn't remember the name of them.

                                              1 Reply Last reply
                                              • stealth007s Offline
                                                stealth007s
                                                Posts: 6,181
                                                stealth007s Offline
                                                stealth007s
                                                wrote on last edited by
                                                #2456 Quote Reply

                                                  @PTRSAK said:
                                                  Actually the Airstream thing did occur to me too, but I couldn't remember the name of them.

                                                  That was my first thought when I saw it too :tu:

                                                  1 Reply Last reply
                                                  • lowtech Offline
                                                    lowtech
                                                    Posts: 4,799
                                                    lowtech Offline
                                                    lowtech
                                                    wrote on last edited by
                                                    #2457 Quote Reply

                                                      ...i had to google the name, too. :)

                                                      1 Reply Last reply
                                                      • bodie Offline
                                                        bodie
                                                        Posts: 27
                                                        bodie Offline
                                                        bodie
                                                        wrote on last edited by
                                                        #2458 Quote Reply

                                                          @WiSAKfan said:
                                                          couple questions for you bodie

                                                          1) can you provide more info (and pics if possible) of the screws you found? i'd love to try tracking some down tomorrow

                                                          1. where did you get 2.2mm pin stock? i thought that was the holy grail of sizes and we were stuck sanding 2.5 (or 3/32) down?

                                                          thank you!

                                                          oh and what spyderco model is that?

                                                          That local store didn't have anymore of the ones I got the first time around :( On my last mod I ended up ordering some 2-56 and 3-48 bolts from newegg and it worked out ok. The side with the nuts actually just press on like normal (with a great deal of force). You can see in the picture below where the inside of the scale took the shape of the bolt. On the other side I had to use krazy glue on the bolt heads to keep the scale on. The snap in the tools is still excellent. Oh, and to give the pin enough room to slide into the scale I had to file down one of the nuts using a dremel.

                                                          1 Reply Last reply
                                                          • enki_ck Offline
                                                            enki_ck
                                                            Global Moderators
                                                            Posts: 20,936
                                                            enki_ck Offline
                                                            enki_ck
                                                            Global Moderators
                                                            wrote on last edited by
                                                            #2459 Quote Reply

                                                              Those are cool :drool: I've never seen anyone do it like this before. Very imaginative :tu:

                                                              1 Reply Last reply
                                                              • WiSAKfan Offline
                                                                WiSAKfan
                                                                Posts: 460
                                                                WiSAKfan Offline
                                                                WiSAKfan
                                                                wrote on last edited by
                                                                #2460 Quote Reply

                                                                  @bodie said:

                                                                  @WiSAKfan said:

                                                                  couple questions for you bodie

                                                                  1) can you provide more info (and pics if possible) of the screws you found? i'd love to try tracking some down tomorrow

                                                                  1. where did you get 2.2mm pin stock? i thought that was the holy grail of sizes and we were stuck sanding 2.5 (or 3/32) down?

                                                                  thank you!

                                                                  oh and what spyderco model is that?

                                                                  That local store didn't have anymore of the ones I got the first time around :( On my last mod I ended up ordering some 2-56 and 3-48 bolts from newegg and it worked out ok. The side with the nuts actually just press on like normal (with a great deal of force). You can see in the picture below where the inside of the scale took the shape of the bolt. On the other side I had to use krazy glue on the bolt heads to keep the scale on. The snap in the tools is still excellent. Oh, and to give the pin enough room to slide into the scale I had to file down one of the nuts using a dremel.

                                                                  did you end up cutting the bolts lengthwise to fit??

                                                                  thank you for the pics and the follow up, i appreciate it. I'm thinking of heading to a hobby store in town and seeing what they have

                                                                  excellent work.

                                                                  anything new up your sleeves?

                                                                  1 Reply Last reply
                                                                  • nuphoria Offline
                                                                    nuphoria
                                                                    Admin Team
                                                                    Posts: 15,038
                                                                    nuphoria Offline
                                                                    nuphoria
                                                                    Admin Team
                                                                    wrote on last edited by
                                                                    #2461 Quote Reply

                                                                      Very clever :tu:

                                                                      Don't see why they can't be modded by any means which works :)

                                                                      1 Reply Last reply
                                                                      • WiSAKfan Offline
                                                                        WiSAKfan
                                                                        Posts: 460
                                                                        WiSAKfan Offline
                                                                        WiSAKfan
                                                                        wrote on last edited by
                                                                        #2462 Quote Reply

                                                                          how my city has changed, drove to two separate hobby stores and both were gone,

                                                                          the local ace hardware had 2-56 and 3-48 but not even close to long enough. got the lead on a place that is open mon-fri

                                                                          ace did have a nice selection of saks that i didn't see until today, they had a pretty diverse selection including explorer, compact, a few 111mm slide locking, and accessories...I picked up a new 91mm pen.

                                                                          1 Reply Last reply
                                                                          • crackout Offline
                                                                            crackout
                                                                            Posts: 864
                                                                            crackout Offline
                                                                            crackout
                                                                            wrote on last edited by
                                                                            #2463 Quote Reply

                                                                              So these are screws with threading over the entire length?
                                                                              Did you notice any change in the folding behaviour of the tools?

                                                                              1 Reply Last reply
                                                                              • WiSAKfan Offline
                                                                                WiSAKfan
                                                                                Posts: 460
                                                                                WiSAKfan Offline
                                                                                WiSAKfan
                                                                                wrote on last edited by
                                                                                #2464 Quote Reply

                                                                                  @crackout said:
                                                                                  So these are screws with threading over the entire length?
                                                                                  Did you notice any change in the folding behaviour of the tools?

                                                                                  that would be the one issue i'm guessing, where the chicago screws that synth007 uses where would be more appropriate

                                                                                  bodie do you have a caliper and could measure the bolts you used?

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  • 121
                                                                                  • 122
                                                                                  • 123
                                                                                  • 124
                                                                                  • 125
                                                                                  • 317
                                                                                  • 318
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. The Mod Squad
                                                                                  4. Show off your Sak mod's!
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0