A "how-to" for basic SAK mods. Pic heavy.
-
Maybe one could add a small table with the pin stock diameters for the different models/pins.
-
93mm: 3.0mm, 2.5mm (center)
Also, 111mm. I'm not quite sure of those.
-
What diameter is the tiny pin?
On a 91mm SAK? It is 2.2mm.
So the fourth pin, or one without the bushing, is 2.2mm? I thought I remembered it being smaller. **Maybe it just looks that way from not having a bushing. **
I think that's exactly what it is, 'cos it's definitely 2.2mm. :D
-
Just adding some info. On 111mm models with the locking blade from the scale, a scissor spring from any scissors can be cut down and fits and works perfectly. Sorry I dont have any pics but all you do is cut a little off at a time until it fits. Remember to test it before you put the scales back on.
-
@tattoosteve99 said:
Just adding some info. On 111mm models with the locking blade from the scale, a scissor spring from any scissors can be cut down and fits and works perfectly. Sorry I dont have any pics but all you do is cut a little off at a time until it fits. Remember to test it before you put the scales back on.I'm not getting what exactly you're saying.
A spring from any scissors? You mean 91mm etc? And for what? The main blade? -
I guess he is referring to the slide lock and that you can use a shortened scissor spring (not backspring) to replace a lost slide lock spring.
-
Ah, that makes sense.
-
Just adding some info. On 111mm models with the locking blade from the scale, a scissor spring from any scissors can be cut down and fits and works perfectly. Sorry I dont have any pics but all you do is cut a little off at a time until it fits. Remember to test it before you put the scales back on.
I'm not getting what exactly you're saying.
A spring from any scissors? You mean 91mm etc? And for what? The main blade?A 91mm scissor spring for the slide lock models.
Sent from my iPhone using Tapatalk
-
and if you don't have a spare scissor spring in your parts box, I have two 111mm slide locks that are relying on a rubber o-ring to push the lock forward rather than a spring.
-
You guys make this look easy...

It wasn't...Posting my agonizing adventure later today. I need a vise so bad, had to peen while holding the brass for a good while. Eventually I wised up... several hours later.
I'll explain and show photos after I get some rest.
-
If you want a way to hold the brass pin stock in a vice without damaging it, here's a nice trick I learned from a blade maker.
Take 2 pieces of flat brass bar or thick sheet, and put them on either side of a business card or thin carboard. Clamp that in a vice, and then get a drill bit for the size of pin stock you want to hold and drill down the center of cardboard.
The drill will naturally follow the cardboard center. Then wen you remove the cardboard and use the brass halves to clamp the pin stock it will hold nice and tight and wont damage the brass like a flat vice will. Drill holes for all the sizes of pin stock you want to hold.

-
Thanks Syph... but I don't own a vise.
You should take a look at my topic. -
I've read that newer 91mm blade liners have a relief stamped in them for the thinner blade tang, while older ones have a flat liner. When did the change over occur? I need to get a flat one for a mod I'm doing.
Will
-
@willfcc said:
I've read that newer 91mm blade liners have a relief stamped in them for the thinner blade tang, while older ones have a flat liner. When did the change over occur? I need to get a flat one for a mod I'm doing.Will
Im not sure when the swap was but yes the liners arent compatible due to the stamped out portion. I dont have any brand new ones, but Im sure I have some older liners off used SAKs if you're stuck and cant find any. They are just sitting around and not something I'll ever use so they have no value to me.
I never tried, but I have wondered before if one could just hammer down the 'bump' in a modern liner to make a flat piece. I think it would work as long as it didn't deform it too much.
-
I was thinking about hammering it flat, but I thought the liner would deform, resulting in poor gap around the scale. It's just laying in the parts bin, guess I'll give it a try. If the mod works, but the fit is poor, I'll PM you?
-
@willfcc said:
I was thinking about hammering it flat, but I thought the liner would deform, resulting in poor gap around the scale. It's just laying in the parts bin, guess I'll give it a try. If the mod works, but the fit is poor, I'll PM you?Yup in the mean time I'll go look and see if I have any in the parts box.
-
You could always file it down flat.
-
Got some mod fodder in with older, thick blades. I'll scrounge a layer from there.
Will
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login